Hama MyVoice2000 User manual

00
137419
Bluetooth-Headset
F
D
PL
GB
Operating Instructions
Bedienungsanleitung
Mode d‘emploi
Instrucciones de uso
Instrukcja obsługi
“MyVoice2000”
E

4
B
A
C D
1
3
45
26

2
Controls and Displays
1. Multi-Function Key
2. Charging Socket
3. Status LED
4. Lautstärkeregler (+)
5. Volume Control (-)
6. Microphone
Thank you for choosing a Hama product.
Take your time and read the following instructions and information
completely. Please keep these instructions in a safe place for
future reference. If you sell the device, please pass these operating
instructions on to the new owner.
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw your
attention to specic hazardås and risks.
Note
This symbol is used to indicate additional information or
important notes.
GOperating instruction

3
2. Package Contents
•1x MyVoice2000 Bluetooth headset
•1x USB charging Cable (B)
•1x Ear Hook (C)
•3x Ear pads (D)
•These operating instructions
3. Safety Notes
•The product is intended for private, non-commercial use only.
•Protect the product from dirt, moisture and overheating, and only
use it in a dry environment.
•Do not allow yourself to be distracted by the product, for example
when driving a vehicle or operating sports equipment. Always pay
attention to the surrounding trac and your environment.
•Do not drop the product and do not expose it to any major
shocks.
•Do not operate the product outside the power limits given in the
specications.
•Do not open the device or continue to operate it if it becomes
damaged.
•Since the battery is integrated and cannot be removed, you will
need to dispose of the product as a whole. Do this in compliance
with the legal requirements.
•Dispose of packaging material immediately according to locally
applicable regulation.
•Do not modify the product in any way. Doing so voids the
warranty.

4
Warning – Rechargeable battery
•Only use suitable charging devices or USB connections for
charging.
•As a rule, do not charge devices or USB connections that are
defective and do not try to repair them yourself.
•Do not overcharge the product or allow the battery to
completely discharge.
•Avoid storing, charging or using batteries in extreme
temperatures.
•We suggest to fully charge the item for at least one time in
two months
4. Getting Started
•The headset is equipped with a rechargeable battery. The battery
must be fully charged before using the device for the rst time.
•Ensure that the headset is switched off before charging it.
•Begin charging by connecting the included USB charging cable
to the charging socket (2) as well as to the USB connection
of a PC/laptop.
•Alternatively, you can charge the headset using a suitable USB
charger. Please refer to the operating instructions for the USB
charger used.
•The status LED (3) lights up constantly in red during the charging
process.
•Charging the battery fully may take up to 2 hours.

5
Warning
Do not use the headset while it is charging.
•If the battery is fully charged, the status LED (3) will go out.
•Disconnect all cable and mains connections after use.
Note
If you have not used the item for a few month, it may take 15-30
minutes for the status LED (3) to red when charging.
5. Operation
Switching the headset on/off
•Turn On:
With the device off, press and hold the multifunction button (1)
for 4 seconds until you hear a voice say “Power on”. The status
LED (3) lights up in blue for about 1 second.
•Turn Off:
With the device on, press and hold the multifunction button (1)
for 4 seconds until you hear a voice say “Power off”. The status
LED (3) will light up in red briey before the device turns off.
The rst time the device is turned on, pairing is automatically started
– see 5.1 Bluetooth pairing.

6
5.1. Bluetooth pairing
Note – Pairing
•Make sure that your Bluetooth-capable terminal device is on
and Bluetooth is activated.
•For more information, please refer to the operating
instructions of your terminal device.
•The headset and the terminal device should not be any further
than 1 metre away from each other. The smaller the distance,
the better.
•Ensure the headset is off.
•Press and hold the multifunction button (1) for approx. 8
seconds until the status LED (3) begins to alternate red and blue.
The headset is searching for a Bluetooth connection.
•Open the Bluetooth settings on your terminal device and wait until
MyVoice2000 appears in the list of Bluetooth devices found.
•Bluetooth devices found.
•Select MyVoice2000 and wait until the headset is listed as
connected in the Bluetooth settings on your terminal device.
Note – Bluetooth password
If your terminal device requests a password to establish the
connection, enter 0000.

7
Note
If pairing was successful, the status LED (3) quickly ashes blue
three times. A voice says, “Your headset is connected”.
•You can now use the headset.
5.2. Automatic Bluetooth connection
(after successful pairing)
Note
•Make sure that your Bluetooth-capable terminal device is on
and Bluetooth is activated.
•For more information, please refer to the operating
instructions of your terminal device.
•Make sure that the headset is switched on.
•After the headset and terminal device have been paired, a
connection is established automatically.
•You can now use the headset.
Note
•If pairing was successful, the status LED (3) quickly ashes
blue three times. A voice says, “Your headset is connected”.
•It may be necessary to change the settings on your terminal
device to enable it to automatically connect to the paired
headset.

8
Hinweis - Connection impaired
After the headset and terminal device have been paired,
a connection is established automatically. If the Bluetooth
connection is not established automatically, check the following:
•Check the Bluetooth settings of your terminal device to see
whether MyVoice2000 is connected. If not, repeat the steps
listed under 5.1 Bluetooth pairing.
•Check whether obstacles are impairing the range. If so, move
the devices closer together.
•The performance can also be affected by a weak battery.
5.3. Multi-pairing
•The headset can be paired with two terminal devices at once so
that, for example, you can use a private and a business mobile
phone simultaneously.
•To begin with, activate Bluetooth only on the rst terminal device
that you wish to pair.
•Pair the rst terminal device with the headset as described in 5.1
Bluetooth Pairing.
•Switch off the headset as described in 5 Operation (Switching
off).
•Activate Bluetooth on the second terminal device.
•Press and hold the multifunction button (1) for approx. 8
seconds until the status LED (3) begins to alternate red and blue.
The headset is searching for a Bluetooth connection.
•Continue as decribed in 5.1 Bluetooth Pairing.
•Once the second terminal device is connected, open the Bluetooth
settings on the rst terminal device and select MyVoice2000.
•Now both terminal devices are connected to the headset.

9
5.4. Hands-free function
Note
•Note that support for certain key functions may vary
depending on your terminal device.
•For more information, please refer to the operating
instructions of your terminal device.
Making a call
•Dial the number directly on your terminal device to make a call.
Voice-activated dialing
•Please check if your mobile phone supports voice dialing function.
•Press the multi-function key (1) briey, then you can hear a
short beep.
•The mobile phone’s voice control will be activated.
•Start a call as described in your mobile phone’s operating
instructions.
•Say the name of person you wish to call.
•If the voice tags are paired to the related phone number stored in
your mobile phone, the number will be dialed.
Accepting calls
•Press the multifunction button (1) once to answer an incoming
call.
Ending a call
•During a call, press the multifunction button (1) once to end
the call.