HAMPTON BAY Carriage House-2 138 108 User manual

52” Carriage House
Ceiling Fan by Hampton Bay
Steeper Blade Pitch for
Greater Air Movement
3-Speed Reverse Function for
Year-Round Comfort and Savings
Accu-Arm™ for Accurate and
Easy Installation
Flush Mount Installation
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our
Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.
Please reference your SKU (412 761 brushed nickel/chrome, 739 887 aged iron, 138 108 polished brass/satin brass)
or UPC (082392 46010 5R brushed nickel/chrome, 082392 46011 2R aged iron, 082392 46008 2R polished brass/satin brass).
Thank you for purchasing this Hampton Bay ceiling
fan. This product has been manufactured with the
highest standards of safety and quality. The nish
of this fan is weather resistant, but over time will
naturally weather and fade.
Safety Rules .................................. 1
Unpacking Your Fan.................... 2
Installing Your Fan ...................... 3
Operating Your Fan ..................... 8
Care of Your Fan.......................... 9
Troubleshooting............................ 9
Specications ................................ 10
Warranty Information................. 11
Table of Contents
UL model no.: 52-CL

Safety Rules .................................. 1
Unpacking Your Fan.................... 2
Installing Your Fan ...................... 3
Operating Your Fan ..................... 8
Care of Your Fan.......................... 9
Troubleshooting............................ 9
Specications ................................ 10
Warranty Information................. 11
1. To reduce the risk of electric shock, insure electricity
has been turned off at the circuit breaker or fuse box
before beginning.
2. All wiring must be in accordance with the National
Electrical Code ANSI/NFPA 70-1999 and local electrical
codes. Electrical installation should be performed by a
qualied licensed electrician.
3. WARNING: To reduce the risk of re or electric shock, do
not use this fan with any solid-state speed control device.
4. The outlet box and support structure must be securely
mounted and capable of reliably supporting a minimum of
35 pounds. Use only UL Listed outlet boxes marked “FOR
FAN SUPPORT.”
5. The fan must be mounted with a minimum of 7 feet
clearance from the trailing edge of the blades to the oor.
6. Do not operate reversing switch while fan blades are in mo-
tion. Fan must be turned off and blades stopped before re-
versing blade direction.
7. Avoid placing objects in path of the blades.
8. To avoid personal injury or damage to the fan and
other items, be cautious when working around or
cleaning the fan.
9. Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be
suitable for most cleaning.
10. After making electrical connections, spliced conductors
should be turned upward and pushed carefully up into
outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding
conductor on one side of the outlet box and ungrounded con-
ductor on the other side of the outlet box.
11. Electrical diagrams are for reference only. Light kits that are
not packed with the fan must be UL Listed and marked suit-
able for use with the model fan you are installing. Switches
must be UL General Use Switches. Refer to the instructions
packaged with the light kits and switches for proper assembly.
12. All set screws must be checked and retightened where neces-
sary before installation.
Safety Rules 1.
READ AND SAVE THESE INSTRUCTIONS
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED “ACCEPTABLE FOR
FAN SUPPORT” WITH THE SCREWS PROVIDED WITH THE OUTLET
BOX.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE BRACKETS (ALSO REFERRED TO AS “FLANGES”) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN
THE PATH OF THE BLADES.

a. Blade Attachment Hardware
(15 Screws)
b. Electrical Hardware
(3 plastic wire connectors, 1 pull chain for
the fan, 1 pull chain for the light kit)
c. Locknut (3)
d. Extra Blade Bracket Hardware
(1 screw and lockwasher)
7. Set of Blades (5)
8. Lamp Shade (4)
1. Mounting Bracket
2. Motor Housing
3. Fan Motor
4. Light Kit Assembly
5. Bulbs (4)
6. Set of Blade Holders (5)
2. Unpacking Your Fan
IMPORTANT: THIS PRODUCT AND/OR COMPONENTS ARE COVERED
BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,947,436;
5,988,580; 5,971,573; 6,010,306; 6,039,541; 6,046,416 AND OTHER
PATENTS PENDING.
Unpack your fan and check the contents. You should have the following items: Loose Parts Bag Containing:
234
1
5678

Loose Parts Bag Containing:
Installing Your Fan 3.
Tools Required
Phillips screw driver, straight slot screw
driver, adjustable wrench, step ladder, and
wire cutters.
Mounting Options
If there isn’t an existing outlet box, then read
the following instructions. Disconnect the
power by removing fuses or turning off
circuit breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 35 lbs.)
Do not use plastic outlet boxes.
Figures 1, 2, and 3 are examples of different
ways to mount the outlet box.
Outlet Box
Outlet Box
To hang your fan where there is an existing
xture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 3
(available at your Hampton Bay retailer).
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT
FAN ONLY TO AN OUTLET BOX MARKED
ACCEPTABLE FOR FAN SUPPORT AND
USE THE MOUNTING SCREWS PROVIDED
WITH THE OUTLET BOX. OUTLET BOXES
COMMONLY USED FOR THE SUPPORT OF
LIGHTING FIXTURES MAY NOT BE ACCEPT-
ABLE FOR FAN SUPPORT AND MAY NEED TO
BE REPLACED. CONSULT A QUALIFIED ELEC-
TRICIAN IF IN DOUBT.
Figure 1
Figure 2
Figure 3

4.
Hanging the Fan
REMEMBER to turn off the pow-
er. Follow the steps below to hang your
fan properly.
1. Securely attach the mounting plate to
the outlet box using the two screws sup-
plied with the outlet box (Figure 4). Pull
the black, white and ground wires out of
the outlet box and through the hole in the
mounting plate and lay them to the side.
2. Carefully lift the fan motor assembly and
engage the slot in the motor bracket with
the hook on the mounting plate so that it
is securely suspended (Figure 5). Then
connect the wiring to your fan according
to the section “Making the Electrical Con-
nections”.
3. Once wiring is completed, lift the motor
bracket so that the threaded studs on the
mounting plate protrude through the slots
in the motor bracket (Figure 5). Securely
tighten the three 1/4” locknuts (supplied)
onto the threaded studs, then try to shake
the motor bracket to ensure that the assem-
bly is tight (Figure 6).
Fan Motor
Assembly
Mounting
Plate
Motor
Bracket
Supply
Wire Lead
Threaded
Studs
Figure 4
Figure 5
Figure 6
FOR BETTER FAN PERFORMANCE, MAKE SURE
THE MOUNTING PLATE IS LEVEL. ADDITIONAL
WASHERS (NOT INCLUDED) MAY BE NEEDED
TO INSERT BETWEEN THE OUTLET BOX AND
MOUNTING PLATE (FIGURE 4).

5.
Figure 7
Making the Electrical
Connections
REMEMBER to disconnect the power.
If you feel you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
Follow the steps below to connect the fan
to your household wiring. Use the wire
connecting nuts supplied with your fan.
Secure the connectors with electrical tape.
Make sure there are no loose strands or
connections.
1. Connect the ground conductor of the 120v
supply (this may be a bare wire or a wire
with green colored insulation) to the green
ground leads from the motor bracket and the
mounting plate of the fan (Figure 7).
2. Connect the fan motor white wire to the
supply white (neutral) wire using a wire nut
supplied (Figure 7).
3. Connect the fan motor black and blue wires
to the supply black (hot) wire using a wire
nut supplied (Figure 7).
4. After connecting the wires, spread them
apart so that the green and white wires are
on one side of the outlet box and the black
wire is on the other side.
5. Turn the wire connecting nuts upward and
push the wiring into the outlet box.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE A SOLID STATE SPEED CONTROL
WITH THIS FAN. IT WILL PERMANENTLY DAMAGE THE ELECTRONIC CIRCUITRY.
CHECK TO SEE THAT ALL CONNECTIONS ARE TIGHT, INCLUDING GROUND, AND THAT NO BARE
WIRE IS VISIBLE AT THE WIRE NUTS, EXCEPT FOR THE GROUND WIRE.
ELECTRICAL DIAGRAMS ARE FOR REFERENCE ONLY. OPTIONAL USE OF ANY LIGHT KIT SHALL BE
UL LISTED AND MARKED SUITABLE FOR USE WITH THIS FAN.

6.
Finishing the Fan
Installation
1. Remove the two screws on two diagonal
sides from the top of the mounting plate and
loosen the other two screws (Figure 8).
2. Align the two key slots on the top of the
motor housing with the two screws on the
mounting plate, push the motor housing up
and turn it clockwise to lock in plate, tighten
the two screws.
3. Install the two screws that were removed
in step 1 into the remaining two holes and
tighten rmly four screws.
Attaching the
Fan Blades
NOTE: Your fan blade are reversible. Select
the blade side nish which best accentuates
your decor.
1. Attach blade to blade bracket using the
screws supplied (Figure 9). Please note that
the rubber washers are pre-attached to the
blade bracket. Start a screw into the bracket.
Repeat for the two remaining screws.
2. Tighten each screw securely.
3. Fasten the blade assembly to the motor by
inserting the alignment posts into the slot
on the bottom of the motor and tightening
the motor screws. Please note that the mo-
tor screws are pre-attached into the blade
brackets (Figure 10).
4. Repeat steps 1-3 for the remaining blades.
Blade Balancing
All blades are grouped by weight. Because nat-
ural woods vary in density, the fan may wobble
even though the blades are weight matched.
The following procedure should correct most
fan wobble. Check after each step.
1. Check that all blade screws are secure.
2. Most fan wobble problems are caused when
blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip
of one of the blades. Measure from a point
on the center of each blade to the point on
the ceiling. Measure this distance as shown
Figure 9
Figure 10
Figure 8

7.
Figure 11
Figure 12
TO REDUCE THE RISK OF PERSONAL INJURY,
DO NOT BEND THE BLADE HOLDERS WHILE
INSTALLING, BALANCING THE BLADES, OR
CLEANING THE FAN. DO NOT INSERT FOREIGN
OBJECTS BETWEEN ROTATING BLADES.
(4)
Attaching the Light Kit
REMEMBER to disconnect the power.
1. Remove the three mounting screws on the
black bracket below the motor.
2. Engage the connector of the switch cup/
light kit assembly with the motor connector
(Figure 12). The two connectors are keyed
and must be matted correctly before they
can be engaged. Make sure the connector
latch closes properly.
3. Position the switch cup/light kit assembly
on the black switch cup plate and align the
three holes in the plate. Make sure the notch
in the switch cup plate clears the reversing
switch in the switch cup/light kit assembly.
Re-install the three mounting screws to se-
cure the switch cup/light kit assembly.
4. To install the glass shade, back the three
knurled screws out until the glass shade
neck slips into the glass holder (Figure
12)”. Then nger tighten the screws un-
til three screws touch the neck with ap-
proximate equal projection on the outside.
NOTE: Periodically check the tightness
of the knurled screws. Fan operation may
loosen these screws.
5. With the power off, insert the light bulbs
into the light sockets. Use 60w max bulbs
(provided).
If you need an extra switch cup
(or cover) for the non-light option,
please call 1-800-283-6513
(M-F 9:00am to 4:30pm EST).
in Figure 11. Rotate the fan until the next
blade is positioned for measurement. Repeat
for each blade. Measurement deviations
should be within 1/8”. Run the fan for 10
minutes.
3. Use the enclosed Bladed Balancing Kit if
the blade wobble is still noticeable.

8. Operating Your Fan
Operating Your Fan
Turn on the power and check the operation of
the fan. The pull chain controls the fan speed
as follows: 1 pull - High, 2 pulls - Medium, 3
pulls - Low and 4 pulls - Off.
Speed Settings for warm or cool weather
depend on factors such as room size, ceil-
ing height, number of fans and so on.
The slide switch controls direction: forward
(switch down) or reverse (switch up). Figure 13
Figure 14
Warm weather - (Forward) A downward
air ow creates a cooling effect as shown
in Figure 13. This allows you to set your
air conditioner on a higher setting without
affecting your comfort.
Cool weather - (Reverse) An upward air
ow moves warm air off the ceiling are as
shown in Figure 14. This allows you to set
your heating unit on a lower setting with-
out affecting your comfort.
WAIT FOR FAN TO STOP COMPLETELY BEFORE
SETTING SLIDE SWITCH TO REVERSE THE DI-
RECTION OF BLADE ROTATION.
TO REDUCE THE RISK OF PERSONAL INJURY,
DO NOT BEND THE BLADE HOLDERS WHILE
INSTALLING, BALANCING THE BLADES, OR
CLEANING THE FAN. DO NOT INSERT FOREIGN
OBJECTS BETWEEN ROTATING BLADES.