HAMPTON BAY EDELWEISS User manual

SKU/Model : #xxx / #SW19028 AC BN
EDELWEISS 52

Fan without Light kit (Optional)

READ AND SAVE THESE INSTRUCTIONS.

We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period
of lifetime after the date of purchase by the original purchaser. And we warrant the LED light kit to be free from defects in workmanship
and material present at time of shipment from the factory for a period of 3 years after the date of purchase by the original purchaser.
We also warrant that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the
time of shipment from the factory for a period of one year after the date of purchase by the original purchaser. We agree to correct such
defects without charge or at our option replace with a comparable or superior model if the product is returned. To obtain warranty service,
you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product are your responsibility.
Damage to any part such as by accident, misuse, improper installation or by affixing any accessories, is not covered by this warranty.
Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding,
tarnishing or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain
amount of "wobble" is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the
warranty invalid. There is no other express warranty. We hereby disclaim any and all warranties, including but not limited to those of
merchantability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be
disclaimed is limited to the time period as specified in the express warranty. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you. The retailer shall not be liable for incidental, consequential, or special
damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do
not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty
givesd specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior
warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.
Ladder
52 in. xxxx’
xxxx xxx xxx xxxx
xxxx xxx xxx xxxx
xxxx xxx xxx xxxx
xxxx xxx
xxx xxx

Fiber washer
15+1 spare
15+1 spare
MM
NN
Blade arm screw
Mounting plate screw (preassembled)
Light kit plate screw (preassembled)
MM
NN
10+1 spare
OO
PP
RR
QQ
OO
PP
QQ
RR
Plastic plug for non-light use

M
M
L
Glass shade
Light kit assembly
N
Blade holders
5
5
9W LED bulbs 2
Metal cap (preassembled)
Finial (preassembled)
O
Light kit plate (preassembled)
N
O

GG II
SS
SS
FF
II
FF
GG
EE
GG
HH
Loosen the two set screws (II) from the coupling of the
fan motor assembly (H)
B
B
B
SS
SS

TT
TT
Hanging the fan motor assembly
to the mounting bracket

the the
the
EB

in
Installing the canopy and canopy cover
JJ
JJ

Fastening the blades to the
blade arms
Attach the fan blade (A) to the blade arm (I) by using the
three blade screws (AA) and the three fiber washer (BB).
Tighten all blade screws (AA) and fiber washers (BB)
securely.
Repeat same process for the other four blades (A).
AA
I
Tighten the blade arm (I) onto the bottom of fan motor
assembly (H) by using the two blade arm screws (CC).
Repeat same process for the other four blade arms (I).
I
CC

Installing the light kit assembly
Remove the light kit plate (J) from the light kit assembly (K) by removing the three light kit plate screws (LL) from the rim of light
kit assembly (K). Keep these three screws (LL) aside for later use.
Remove one of the screws (KK) from the mounting plate of the fan motor assembly (H) and loosen the other two screws (KK), but
do not remove.
Place the key holes from the light kit plate (J) over the two screws (KK) previously loosened from the mounting plate of the fan
motor assembly (H). Turn the light kit plate (J) until it locks at the narrow section of the key holes. Secure by tightening the two
screws (KK) previously loosened and the one screw (KK) previously removed.
While holding the light kit assembly (K) under your fan, firmly snap the wire connection plugs (UU) together.
Align the three holes in the light kit assembly (K) with the three holes in the light kit plate (J). Tighten the three light kit plate screws
(LL) removed in first step.
LL
K
J
UU
K
KK
J
H
J
LL

10
N
O
L
M
MM
NN
OO
Installing the light bulbs and the glass shade
Install 2*9W LED bulbs (O) into the sockets.
Remove the rubber washer (MM), metal washer (NN), hex nut (OO), metal cap (L) and finial (M) from the light kit
assembly (K).
Place the glass shade (N) over the light kit stem, secure with rubber washer (MM), metal washer (NN), hex nut (OO), metal
cap (L) and finial (M). Do not over tighten.

Push the plastic plug (QQ) into the center hole of the
switch cup.
Holding the switch box under your fan, snap together the
wire connection plugs (UU).
Install the switch cup to the light kit plate with the
previously removed.
Align the three holes in switch box with the three holes in
the light kit plate (J). Tighten the three light kit plate screws
(LL) removed in last step.
QQ
Installing the switch box only
for non-light use
11 12
J
LL
Separate the switch box from
the light kit assembly
Fan without Light kit (Optional)
Disconnect the wire connectors (VV) and remove the
washer (WW), nut (XX), So that the switch box can be
separated from the light kit assembly (K).
K
K
WW
XX
VV
UU

The 3-speed pull chain (YY)
Reverse Function
The light kit pull chain
left
right
Attach the pull chain fob (PP) to the chain on the light kit assembly (K)
YY
PP
ZZ
K
The reverse switch (ZZ) is located on the surface of the light kit
assembly (K).

Balancing kit includes an
additional instruction manual within the packet.
10

MM
NN
OO
PP
RR
QQ
Fiber washer
Blade arm screw
Mounting plate screw (preassembled)
Light kit plate screw (preassembled)
MM
NN
OO
PP
QQ
RR
Plastic plug for non-light use
LGlass shade
Light kit assembly
N
Blade holders
9W LED bulbs
Cap
Finial
O
Switch box plate
M
M
N
O
18

CF552KP-03
HAMPTON BAY