HAMPTON BAY Isolabella User manual

Isolabella
54" Ceiling Fan
With Remote Control
Owner’s Manual
Hampton Bay®
Classic Collection
Isolabella
Ventilador de Techo de 54"
con Control Remoto
Manual del Propietario

Date Purchased
Store Purchased
Model No.
Serial No.
Vendor No.
UPC
Hampton Bay Lifetime Limited Warranty
The retailer warrants the fan motor to be free from defects in workmanship and material
present at time of shipment from the factory for a lifetime after the date of purchase by the
original purchaser. The retailer also warrants that all other fan parts, excluding any glass or
plexiglass blades, to be free from defects in workmanship and material at the time of
shipment from the factory for a period of one year after the date of purchase by the original
purchaser. We agree to correct such defects without charge or at our option replace with a
comparable or superior model if the product is returned to the retailer. To obtain warranty
service, you must present a copy of the receipt as proof of purchase. All costs of removing
and reinstalling the product are your responsibility. Damage to any part such as by accident
or misuse or improper installation or by affixing any accessories, is not covered by this
warranty. Because of varying climatic conditions in the United States this warranty does
not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or
peeling. Brass finishes of this type give their longest useful life when protected from
varying weather conditions. A certain amount of wobble is normal and should not be
considered a defect. Servicing performed by unauthorized persons shall render the warranty
invalid. There is no other express warranty. The retailer hereby disclaims any and all
warranties, including but not limited to. Those of merchantability and fitness for a
particular purpose to the extent permitted by law. The duration of any implied warranty
which cannot be disclaimed is limited to the time period as specified in the express
warranty. Some states do not allow limitation on how long an implied warranty lasts, so the
above limitation may not apply to you. The retailer shall not be liable for incidental,
consequential, or special damages arising out of or in connection with product use or
performance except as may otherwise be accorded by law. Some states do not allow the
exclusion of incidental or consequential damages, so the above exclusion or limitation may
not apply to you. This warranty gives specific legal rights, and you may also have other
rights which vary from state to state. This warranty supersedes all prior warranties.
Lifetime Limited Warranty
108-974
11289
792145351818

Safety Rules..............................................................................................................
Unpacking Your Fan ....................................................................................................
Installing Your Fan ......................................................................................................
Installing the .....................................................................................
Your .........................................................................................
Care of Your Fan .......................................................................................................
Troubleshooting .......................................................................................................
Specifications ..........................................................................................................
Decorative Cover
Operating Transmitter
1.
2.
3.
9.
10.
11.
12.
13.
Table of Contents

1. Safety Rules
1.To reduce the risk of electric shock, insure electricity has been
turned off at the circuit breaker or fuse box before beginning.
2. All wiring must be in accordance with the National Electrical
Code and local electrical codes. Electrical installation should be
performed by a qualified licensed electrician.
3. WARNING: To reduce the risk of electrical shock and fire, do not
use this fan with any solid-state fan speed control device.
4. WARNING: To reduce the risk of personal injury, use only the two
steel screws (and lock washers) provided with the outlet box for
mounting to the outlet box. Most outlet boxes commonly used for
the support of lighting fixtures are not acceptable for fan support
and may need to be replaced, consult a qualified electrician if in
doubt.
8. Avoid placing objects in the path of the blades.
9. To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be
suitable for most cleaning.
11. After making electrical connections, spliced conductors should
be turned upward and pushed carefully up into the outlet box.
The wires should be spread apart with the grounded conductor
and the equipment-grounding conductor on one side of the outlet
box.
12. Electrical diagrams are for reference only. Light kits that are not
packed with the fan must be UL Listed and marked suitable for
use with the model fan you are installing. Switches must be UL
General Use Switches. Refer to the Instructions packaged with
the light kits and switches for proper assembly.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR
FAN SUPPORT.
5. The outlet box and support structure must be securely mounted
and capable of reliably supporting a minimum of 50 pounds. Use
only UL Listed outlet boxes marked FOR FAN SUPPORT.
6. The fan must be mounted with a minimum of 7 feet clearance
from the trailing edge of the blades to the floor.
7. Do not operate the reverse switch while the fan blades are in
motion. The fan must be turned off and the blades stopped before
reversing the blades direction.
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING ASSEMBLY
OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN THE PATH OF
THE BLADES.
NOTE
READ AND SAVE ALL INSTRUCTIONS!

Unpack your fan and check the contents. You should have the following items;
.
1. Fan blades (5)
2. Canopy assembly
3.
Decorative scroll ring
5. Decorative scroll arms
6.
7. Fan motor assembly
8. Glass housing
9. Glass housing plate
10. Blade arms (5)
Ball/downrod assembly (1)
& extra downrod (1)
4.
(4)
Coupling cover
11. Blade arm holder
12. Metal holder
13. Decorative cover
14. Decorative nut
15. Receiver with 6 wire nuts
16. Transmitter+holder+2 mounting screws
+ 2 plastic plugs
17. 15 Watt candelabra bulbs (4)
18. 12V MN21/A23 battery
19. Balancing kit
3
1
210
11
12
13
14
4
5
6
7
8
9
15
16
17
19
18
Unpacking Your Fan 2.
WARNING
DO NOT INSTALL OR USE FAN
IF ANY PART IS DAMAGED OR MISSING.
CALL TOLL FREE 1-877-898-1881
20
20. Loose parts bag containing:
a. Blade attachment hardware
(16 )
b. Mounting hardware
( 3 plastic wire connectors)
c. B
d
screws, 16 Fiber washers
hardware
(6 screws)
(11 screws)
lade arm holder
. Blade arm hardware
a
cd
b

Tools Required
Phillips screwdriver, straight slot
screwdriver, adjustable wrench, step
ladder, and wire cutters.
Mounting Options
If there isn't an existing UL listed
mounting box, then read the following
instructions. Disconnect the power by
removing fuses or turning off circuit
breakers.
Secure the outlet box directly to the
building structure. Use appropriate
fasteners and building materials. The
outlet box and its support must be able
to fully support the moving weight of the
fan (at least 50 lbs). Do not use plastic
outlet boxes.
Figures 1,2 and 3 are examples of
different ways to mount the outlet box.
Note: You may need a longer downrod to
maintain proper blade clearance when
installing on a steep, sloped ceiling.
To hang your fan where there is an existing
fixture but no ceiling joist, you may need
an installation hanger bar.(Fig.4)
(available at any Home Depot store).
Outlet box
Outlet box
Outletbox
Figure 1
Figure 2
Figure 4
3. Installing Your Fan
Provide strong support
Recessed
outlet box
Mounting bracket
opening must be
toward the top
Figure 3
Angled ceiling
maximum
18 angle

4.
Hanging the Fan
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
Step 1. Remove the decorative canopy
bottom cover from the canopy by turning the
cover counter clockwise.(Fig. 5)
Step 2. Remove the hanger bracket from the
canopy by loosening the two screws on the
bottom of the hanging bracket
from the screw head and turning the canopy
counter clockwise.(Fig. 5)
Step 3. Pass the 120-volt supply wires
through the center hole in the ceiling hanger
bracket.(Fig. 6)
Step 4. Secure the hanger bracket to the
ceiling outlet box with the screws and
washers provided with your outlet box. (Fig. 6)
Step 5. Remove the hanger pin, lock pin and
set screws from the top of the motor
assembly.
Step 6. Route wires exiting from the top of
the fan motor through the collar cover,
d canopy cover, canopy
and then through the ball / downrod. (Fig. 7)
Step 7. Align the holes at the bottom of the
downrod with the holes in the collar on top of
the motor housing (Fig. 7). Carefully insert
the hanger pin through the holes in the collar
and downrod. Be careful not to jam the pin
against the wiring inside the downrod. Insert
the locking pin through the hole near the end
of the hanger pin until it snaps into its locked
position, as noted in the circle inset of Fig. 7.
a half turn
ecorative scroll ring,
WARNING
FAILURE TOPROPERLY INSTALL LOCKING PIN AS
NOTED IN STEP 7 COULD RESULT IN FAN
LOOSENING AND POSSIBLY FALLING.
Step 8. Tighten two set screws at top of the
fan motor collar firmly. (Fig. 7)
Step 9. Install the 4 x 15W bulbs (provided)
into the sockets of the bulb holder assembly.
(Fig. 8)
Step10. Install the decorative scroll arms to
the decorative scroll ring and motor with the
screws provided. Be sure to tighten all screws.
(Fig. 8)
Step 11. Place the downrod ball into the
hanger bracket socket. Rotate the downrod
ball until the groove of the downrod ball
lines up with the hook of the hanger bracket.
(This will help balance the fan.)
Figure 5
Hanger
bracket
Ceiling
canopy
Canopy
cover
Motor collar
Collar cover
Pin in
locked
position
Ball/downrod
assembly
Ceiling
canopy
Tighten screws
firmly
Locking pin
Canopy
cover
Decorative
scroll ring
Hanger pin
Figure 7
Mounting
screws
(supplied with
electrical box)
Hook
UL Listed
electrial
box
Figure 6 120V Wires
Washers
Hanger
bracket

Make the Electric Connections
WARNING: To avoid possible electrical
shock, be sure electricity is turned off at the
main fuse box before wiring.
NOTE: This remote control unit is equipped
with 16 code combinations to prevent
possible interference from or to other remote
units. The frequency switches on your
receiver and transmitter have been preset at
the factory. Please recheck to make sure the
switches on transmitter and eceiver
are set to the same position, any
combination of settings will operate the fan
as long as the transmitter and receiver are
set to the same position.(Fig. 9)
Step 1. (Fig. 10) Insert the receiver into
the mounting bracket with the flat side of
the receiver facing the ceiling.
Step 2. (Fig. 11) Motor to Receiver Electrical
Connections: Connect the black wire from
the fan to black wire marked "TO MOTOR L".
Connect the white wire from the fan to
the white wire marked "TO MOTOR N" from
the receiver. Connect the blue wire from the
fan to the blue wire marked "For Light" from
the receiver. Secure the wire connections
with the plastic wire nuts provided.
the the r
5.
Figure 8
Screws
Bulbs
Canopy
cover
Decorative
scroll ring
Decorative
scroll arms
Changing the Downrod (Optional)
NOTE: Your fan comes with a 12" downrod
attached to the hanger ball. In addition, a 4-
1/2" downrod has been provided to be used
in case the ceiling is lower. In this case,
perform the following steps for correct
installation:
1. Remove the hanger ball from downrod by
loosening the setscrew at the top of the
downrod which holds the hanger ball to
the downrod.
2. Slide the hanger ball down the downrod
and remove the support pin.
3. Insert the support pin in the holes at the
top of the 4-1/2" downrod and slide the
hanger ball up the 4-1/2" downrod. Make
sure the support pin is properly seated in
the grooves in the top of the hanger ball.
4. Tighten the setscrews firmly.
NOTE: Do not install the decorative scroll if
you plan to use the 4-1/2" downrod.
NOTE: Your fan comes with a 12" downrod
for 9' ceiling. A 4-1/2" downrod has been
provided to be used in case the ceiling is 8'.

Receiver
Hanger bracket
Figure 9
Figure 10
6.
ONON
Code switch
Figure 11
Step 3. (Fig. 11) Receiver to House Supply
Wires Electrical Connections: Connect the
black (hot) wire from the ceiling to the
black wire marked "AC in L" from the
receiver. Connect the white(neutral) wire
from the ceiling to the white wire marked
"AC in N" from the Receiver. Secure the
wire connections with the plastic wire nuts
provided.
Step 4. (Fig. 11) If your outlet box should
have a ground wire (green or bare copper)
connect it to the fan's ground wires;
otherwise connect the hanging bracket
ground wire to the grounded metal junction
box. Secure the wire connection with a
plastic nut provided. After connecting the
wires spread them apart so that the green
and white wires are on one side of the
outlet box and black and blue wires are on
the other side. Carefully tuck the wire
connections up into the outlet box.
Note: Fan must be installed at a maximum
distance of 20 feet from the transmitting
unit for proper signal transmission
between the transmitting unit and the fan's
receiving unit.
CAUTION: Do not use with wall light
dimmer switch.
SUPPLY CIRCUIT
Ground
Conductor
Outlet Box
Green
Ground
Lead
Ground to
Downrod
BLACK
WHITE
WHITE
WHITE
WHITE
BLACK
BLACK
BLACK
BLUE
BLUE
GREEN
ONON

7.
Installing the Glass
Housing
1. Remove 1 of the 4 screws from the
bottom of the motor housing and loosen
the other 3 screws. (Do not remove)
2. Raise and hold the glass housing close
to the motor, place the key holes on the
glass housing plate over the 3 screws
previously loosened from the motor
housing, turn glass housing plate until
it locks in place at the narrow section of
the key holes. Secure by tightening the
3 screws previously loosened and the
one previously removed. (Fig. 13)
Figure 13
Motor
housing
Glass housing
Glass housing
plate
Screws
Figure 12
Finishing the Installation
Step 1. Tuck connections neatly into ceiling
outlet box.
Step 2. Slide the canopy up to ceiling and
over the 2 screws on the hanger bracket.
Rotate canopy clockwise. Next, while holding
the canopy with one hand, slide the canopy
cover over the screws and rotate clockwise
until tight. Note: adjust the canopy screws as
necessary until the canopy and canopy cover
are snug. (Fig. 12)
WARNING
Make sure the hook on the hanging
bracket properly sits in the groove in the
hanger ball before attaching the canopy
to the bracket by turning the housing
until it drops into place.
Outlet box
Hanger
bracket
Hanger
ball
Canopy
Canopy
cover