BLUEFIN Fitness Weights Bench User manual

For use with BLUEFIN FITNESS Weights Bench

Dear customer,
We are pleased that you have chosen a device from the BLUEFIN
FITNESS product range. BLUEFIN FITNESS sports equipment offers
you the highest quality and latest technology.
In order to take full advantage of the device‘s performance, and to
have many years of pleasure in your device, please read this manual
carefully before commissioning and starting the training and use
the device according to the instructions. The operational safety and
function of the device can only be guaranteed if the general safety and
accident prevention regulations of the legislator as well as the safety
instructions in this user manual are observed. We assume no liability
for damages caused by improper use or incorrect operation.
Please make sure that all persons using the device
have read and understood the user manual.
Please make sure that all persons using the device have read and
understood the user manual.

1. SAFETY PRECAUTIONS
2. HARDWARE PACK
3. COMPONENTS
4. ASSEMBLY INSTRUCTION
5. CONFIGURATIONS
6. EXPLODED VIEW
7. CARE AND MAINTENANCE
8. TECHNICAL SPECIFICATIONS
9. PART LIST
10. TRAINING INSTRUCTIONS
TABLE OF CONTENTS

1. SAFETY PRECAUTIONS
This exercise machine is built for optimum safety. However,
certain precautions apply whenever you operate a piece of exercise
equipment. Be sure to read the entire manual before you assemble
or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symp-toms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near
water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes
or other clothing that could become caught in the machine. Running or aerobic
shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT
use attachments not recommended by the manufacturer.
8. The free area must be at least 0.6m greater than the training area. This is a space
where you can safely dismount, without obstruction, in case of an emergency.
Where two pieces of equipment are positioned adjacent to each other the free
area may be shared.

BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FIT-NESS
EQUIPMENT. WE ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE
USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
WARNING

2. HARDWARE PACK
# 25 M10 x 155mm Allen Bolt (1 pc.)
# 26 M10 x 150mm Allen Bolt (1 pc.)
# 27 M10 x 72mm Allen Bolt (3 pcs.)
# 28 M10 x 18mm Allen Bolt (4 pcs.)
# 31 (16 pcs.)
Ø 10 Washer
# 32 (8 pcs.)
Ø 10 Washer
# 33 M10 Nut
(5 pcs.)
# 35 M8 x 20mm Allen Bolt (1 pcs.)
# 29 M10 x 40mm Allen Bolt (8 pcs.)

3. COMPONENTS

4. ASSEMBLY INSTRUCTION
It is strongly recommend that two or more persons
assemble this Weights Bench.
Tool required to assemble the machine: 2 x
adjustable wrenches + 1 x Philips screwdriver
Note: Some of the accessories are pre-fitted in
the master component, they may not be supplied
separately.
Step 1
A. Attach the Front Support (2#) onto the stabiliser (7#), Align the
holes and secure them with 2 pc M10*18 Allen Bolt (28#) and 2 pcs
Ø10 Washer (31#).
Allen Wrench

Step 2
A. Attach the rear frame (6#) to the stabilizer (7#), Align the holes and
secure them with 2 pc M10*18 Allen Bolt (28#) and 2 pcs Ø10 Washer
(31#).
B. Insert the rear frame (6#) into the main frame (1#), Secure them
with 1 pc M10*72 Allen bolt (27#), 2 pcs Ø10 Washer (31#),1 pc M10
Aircraft nut (33#) and 1 pc Ø53.M18.1,5 Lock knob (21#).
Allen Wrench

Step 3
A. Attach the main frame (1#) to the Front Support (2#), Secure them
with 1pc lock pin (19#), 1 pc M10*72 Allen bolt (27#), 2 pcs Ø10 Washer
(31#), 1 pc M10 Aircraft nut (33#) and 1 pc M8*20 Lock knob (20#).
Allen Wrench

Step 4
A. Attach the 2 pcs backrest pad support (3#) as the diagram shows,
Secure them with 1 pc M10.155 Allen bolt (25#), 2 pcs Ø10 washer
(31#) and 1 pc M10 Aircrafut nut (33#).
B. Attach the incline support (4#) to the backrest pad support (3#) and
secure them together with 1 pc M10*150 allen bolt (26#), 2 pcs Ø10
washer (31#) and 1 pc M10 Aircrafut nut (33#). You would select the
desired incline when exercising.
Allen Wrench

Step 5
A. Place the seat pad (15#) onto the main frame and secure it with 4
pcs M8*40 Allen bolt (29#) and 4 pcs Ø8 washer (32#).
B. Please the backrest pad (14#) onto the backrest pad support (3#)
and secure it with the same way.
Allen Wrench

Step 6
A. Insert the adjustment frame (8#) into the front support (2#), select
the desired height with the M16 lock knob (22#).
B. Insert the foam roll tube (9#) into the hole of the adjsutment frame
as the diagram and secure it with 1pc M8*25 Allen bolt (35#).
C. Attach the leg holder (5#) to the front support (2#) and secure it with
1 pc M10*72 Allen bolt (27#), 2 pcs Ø10 washer (31#) and 1 pc M10
Aircrafut nut (33#).
Allen Wrench
Allen Wrench

Step 7
A. Attach the 2 pcs big foam roll (13#) and 2 pcs small foam roll (12#)
from both ends and add the 2 pcs hand grips (11#) as the diagram
shows.

5. CONFIGURATIONS
Folding the training device
Place the backrest pad to the lowest level and remove the lock knob
(20#) and Lock pin (15#).
Fold the front support and secure it with the lock pin (19#) and lock
knob (20#).

Horizontal lift up of the device
Pull the rear frame (6#) from the main frame (1#).
Loosen the lock knob and fold the rear
frame (6#) as the diagram shows.

Lower the backrest (negative position)
Tighten the lock knob (21#).
orange colour line
Push rear frame (6#) all the way into the main frame
(1#) until the orange color line reach the edge of the
locking block on main frame (1#).

6. EXPLODED VIEW
7. CARE AND MAINTENANCE
1. Examine the equipment periodically in order to detect any damage or wear which
may have been produced.
2. Lubricate moving parts with light oil periodically to prevent premature wear.
3. Inspect and tighten all parts before using the equipment, replace any defective
parts immediately, and do not use the equipment again until it is in perfect
working order.
4. The equipment can be cleaned using a damp cloth and mild non-abrasive
detergent. Do not use solvents.
5. Do not attempt to repair this equipment yourself. Should you have any difficulty
with assembly, operation or use of your exercise product or if you think that you
may have parts missing, contact the manufacturer.

8. TECHNICAL SPECIFICATIONS
9. PART LIST
• The Netto weight of the model is 15.5 KG
• The assembly size is :1600 x 420 x 950 mm
• User weight: 120 kg
• Max. Weight of the weight bench: 185kg
• This appliance has been tested and it complies with standard EN ISO 20957-1:
2013 Class H
1. Main frame
2. Front Support
3. Backrest pad support
4. Incline support
5. Leg holder
6. Rear frame
7. Stabilizer
8. Adjustment frame
9. Foam roll tube
10. Foot
11. Handle grip
12. Big Foam roll
13. Small Foam roll
14. Backest pad
15. Seat pad
16. 25 Square end cap
17. 25 Round end cap
18. 45 Square end cap
1
1
2
1
1
1
2
1
1
4
2
2
2
1
1
8
4
1
1
1
1
1
1
1
1
1
3
4
8
1
14
8
5
2
2
2
No. Description Pcs. No. Description Pcs.
19. Lock pin
20. M8*20 Lock knob
21. Ø53×M18×1,5 Lock knob
22. M16 Lock knob
23. 50×45 Square sleeve
24. Rubber bumper
25. M10×155 Allen bolt
26. M10×150 Allen bolt
27. M10×72 Allen bolt
28. M10×18 Allen bolt
29. M10×40 Allen bolt
30. Philips screw
31. Ø10 Washer
32. Ø8 Washer
33. M10 Nut
34. Bushing
35. M8×25 Allen bolt
36. Rubber production sleeve