Hans Grohe Ecostat 1001 SL 13241 1 Series User manual

Ecostat 1001 SL
13261XX1
Ecostat 1001 SL
13241XX1
Installation Instructions / Warranty

2
13241XX1
Technical Data
Operating pressure: max. 145 psi
Recommended operating pressure: 14.5 - 72 psi
Hot water temperature: 120° F - 140° F*
Rate of ow at 45 psi 5.3 gpm
Protection against back siphonage provided by check valves
in the hot and cold inlets and on the handshower outlet.
*Please know and follow all applicable local plumbing codes when
setting the temperature on the water heater.
Installation considerations
13261XX1
Large dierences in pressure between the hot
and cold water supplies should be balanced
Flush the supplies thoroughly of building debris
before installing this unit.
The oset adapters included with this unit require
½" female ttings, recessed ³⁄₁₆" behind the
surface of the nished wall.
The high temperature limit stop may be reset to
comply with local plumbing codes.
To prevent scald injury, the maximum output tem-
perature of the shower valve must be no higher
•
•
•
•
•
than 120º F. In Massachusetts, the maximum
output temperature can be no higher than 112º
F.
For use in Canada and the USA the mounted
handshower must be equipped with a non return
valve complying with ASME A112.18.3-2002
Keep this booklet and the receipt (or other proof
of date and place of purchase) for this product
in a safe place. The receipt is required should it
be necessary to request warranty parts.
•
•

3
Rough in
Install ½" NPT female ttings, recessed ³⁄₁₆" behind the surface
of the nished wall, for the hot and cold water supplies.
The ttings should be 5⅞" apart on center.
For proper operation of the thermostatic
mixer, the hot supply must be on the left
and the cold supply must be on the right.
Install the nished wall. Make sure that the wall is watertight.
Installation
Wrap the inlet threads on the oset adapters with Teon thread
tape.
Screw the oset adapters into the female ttings.
The outlets of the oset adapters should be 5⅞" apart on center.
Make sure that the adapters are level.
³⁄₁₆"

4
They should extend 1⅜" outside the surface of the nished
wall.
Seal the wall around the oset adapters
with waterproof sealant.
Failure to seal the wall can lead to water
damage.
Position the valve over the oset adapters (1).
Secure the valve to the adapters by rotating the nuts clockwise
(2).
Install the handshower check valve and washer (3).
Install the handshower and hose (not included).
Reset the high temperature limit stop, if desired.
Justify the thermostatic mixer handle.
13261XX1 only: Reset the Ecostop, if desired, to limit the
ow of water to the handshower to 2.6 gpm.
1⅜"
1
2
3

5
Justify the Thermostatic Mixer Handle
Turn the water on.
Turn the thermostatic mixer handle until the output water is
100°F.
Turn the water o.
Remove the screw cover.
Remove the handle and safety set.

6
Reset the High Temperature Limit Stop
The high temperature limit stop may be reset to comply with
local plumbing codes.
Remove the thermostatic mixer handle and safety step.
Remove the high temperature limit stop clip and ring.
Reinstall the safety set so that it is oriented as shown in the
diagram.
Reinstall the handle with the override button at the 12:00
position.

7
Turn the water on.
Turn the thermostatic mixer stem until
the output water is the desired high
temperature (usually 110°F).
Turn the water o.
Replace the high temperature limit stop ring so that the tooth
is against the stop. Replace the clip.
Justify and install the handle.

8
Set the EcoStop (model 13261XX1
only)
Remove the screw cover.
Remove the volume control / diverter handle and the ow
control stop.
Turn the volume control stem until the ow rate is approxi-
mately 2.6 gpm.


Install the ecostop ring so that it is oriented as shown in
the diagram.
Reinstall the handle and screw cover.

10
User Instructions
Using the thermostatic mixer:
Turn the handle to change the temperature of the water, clock-
wise to make the water cooler, counter-clockwise to make the
water warmer.
While making the water warmer, the handle will stop when the
output water is 100°F.
To obtain water warmer than 100°F, press the safety stop over-
ride button and continue turning the hanldle counter-clockwise.
13241XX1: Turn the volume control / diverter handle to
turn the water on and o from the tub spout.
To select the handshower, press and hold the diverter button
while turning the handle.
13261XX1: The volume control handle turns the water on and
o and controls the volume.
The handle will stop when the amount of water coming from the
valve is 2.6 gpm.
If more water is desired, press the green button and continue
turning the handle.
Note to US users: by law, all handshowers sold in the US
are ow restricted to 2.5 gpm.