Hans Grohe Talis M54 210 2jet 72800 3 Series Manual

ZH 用户手册/组装说明 2
EN Instructions for use / Assembly instructions 3
Lesezeichen
中文 2
English 3
Talis M54 210 2jet
72800XX7
Talis M54 210 1jet
72802XX7
Talis M54 270 1jet
72808XX7

2
中文
安装 (参见第页4)
安全技巧
装配时为避免挤压和切割受伤,必须戴上手套.
冷热水管间过大的压力差必须予以平衡.
安装提示
• 安装前必须检查产品是否受到运输损害.安装后
将不认可运输损害或表面损伤.
• 管道和阀门必须根据通用标准进行安装,冲洗和
检查.
• 请遵守当地国家现行的安装规定.
技术参数
工作压强: 最大1MPa
推荐工作压强:0,1-0,5MPa
测试压强:1,6MPa
(1MPa=10bar=147PSI)
热水温度: 最大60°C
热力消毒:70°C/4分钟
该产品专为饮用水设计!
符号说明
请勿使用含有乙酸的硅胶!
调节 (参见第页10)
热水温度调节.如果使用即热式喷头,则不建议安
装热水阀门.
保养 (参见第页16)
单向阀必须在符合国家或当地的法律的情况下按照
EN806-5定期检查(至少一年一次).
大小 (参见第页11 )
流量示意图 (参见第页11 )
备用零件 (参见第页17)
XX=颜色代码
00=镀铬
67=MattBlack
清洗 (参见第页14)
操作 (参见第页20)
汉斯格雅建议,清晨或在水流长时间停滞后,前半
升水不作饮用水使用.
问题 原因 补救
龙头不灵活 - 阀芯损坏,结垢 - 更换阀芯
龙头滴水 - 阀芯损坏 - 更换阀芯
水从龙头出水嘴流出 - O形环损坏 - 更换O形环
水从螺纹底座中流出 - 连接软管没有完全旋入基体 - 用手拧紧连接软管
- 连接软管的O形环损坏 - 更换O形环
热水温度过低 - 温度限制器设置错误 - 设置温度限制器

3
English
Assembly (see page 4)
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The hot and cold supplies must be of equal pressures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Thermal disinfection: 70°C / 4 min
The product is exclusively designed for drinking water!
Symbol description
Do not use silicone containing acetic acid!
Adjustment (see page 10)
To adjust the hot water limiter. Using a hot water limiter in
combination with a continuous flow water heater is not
recommended.
Maintenance (see page 16)
The check valves must be checked regularly according to
EN 806-5 in accordance with national or regional
regulations (at least once a year).
Dimensions (see page 11 )
Flow diagram (see page 11 )
Spare parts (see page 17)
XX = Colors
00 = Chrome Plated
67 = Matt Black
Cleaning (see page 14)
Operation (see page 20)
Hansgrohe recommends not to use as drinking water the
first half liter of water drawn in the morning or after a
prolonged period of non-use.
Fault Cause Remedy
Mixer stiff - Cartridge defective, calcified - Exchange cartridge
Mixer dripping - Cartridge defective - Exchange cartridge
Water escaping in area of swivel
spout
- O-ring defective - Exchange O-ring
Water escaping at the threaded base - connection hoses not completely
screwed into basic body
- Tighten connection hoses by hand
- O-ring at the connection hose
defective.
- Exchange O-ring
Hot water temperature too low - Hot water limiter incorrectly set - Set hot water limiter

4
max. 45 mm
1a 2
(3 Nm)
max. 70 mm
1b
150°
110°
6a
6d6b
6c
5
34
60°
360°
SW 24 mm
(4 Nm) 1.
SW 9 mm
SW 19 mm
(4 Nm)
2.
Montage

5
150°
45°
105°
75° 75°
45°
105°
24 x 15°
6a
Montage

6
24 x 15°
6b
110°
25° 85°
55° 55°
25°
85°
110°
Montage

7
24 x 15°
6c
60°
45° 15°
30° 30°
60°
Montage

8
6d
360°
1.
2.
3.
7 8
Armaturenfett
Grease
䀵滑油
1.
2.
Montage

9
> 2 min
Armaturenfett
Grease
䀵滑油
1.
2.
3.
1.
2.
9
11 12
13
1.
2.
3.
80
CLICK
10
Montage

0,3 MPa
60 °C 10 °C
10
Justierung
65
3 4
36°C
38°C
43°C
60°C
55°C
50°C
1 2
1.
2.
SW 2,5 mm
4 x
1.
2.
SW 2,5 mm
(3,5 Nm)