Harbor Freight Tools CentralPneumatic 60801 Assembly instructions

!"#"$%&'(%)*+#"$*%,$-%.$$/-00)))1.,(+&(2(*"3.$14&5
65,"7%&'(%$*4.8"4,7%#'//&($%,$-%/(&9'4$#'//&($:.,(+&(2(*"3.$14&5
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 21b
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2021 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly an d se rv ic e may n ot b e in cl uded.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 60801 60802
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
G,+7*%&2%O&8$*8$#
Safety ......................................................... 2
Specifications ............................................. 6
Setup .......................................................... 7
Operation .................................................... 8
Maintenance .............................................. 10
Parts List and Diagram .............................. 11
Warranty .................................................... 12
QFKMLMR%EHNSITE%FMU%U6;LMLGLIME
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
LNJIKGFMG%EF;6GH%LMEGKPOGLIME
LMEGKPOGLIME%J6KGFLMLMR%GI%F%KLEV%I;%;LK6=%
6T6OGKLO%EWIOV=%IK%LMXPKH%GI%J6KEIME
QFKMLMR – When using tools, basic precautions should always be followed, including the following:
R*8*(,7
G&%(*9'4*%$.*%("#Y#%&2%*7*4$("4%#.&4Y=%2"(*=%,89%"8Z'([%$&%/*(#&8#=%
(*,9%,77%$.*%"8#$('4$"&8#%+*2&(*%'#"83%$.*%$&&71
Q&(Y%F(*,
1. V**/%$.*%)&(Y%,(*,%47*,8%,89%)*77%7"3.$*91%%
Cluttered benches and dark areas increase the
risks of electric shock, fire, and injury to persons.
2. U&%8&$%&/*(,$*%$.*%$&&7%"8%*\/7&#"]*%
,$5&#/.*(*#=%#'4.%,#%"8%$.*%/(*#*84*%
&2%27,55,+7*%7"<'"9#=%3,#*#=%&(%9'#$1
The tool is able to create sparks resulting
in the ignition of the dust or fumes.
3. Keep bystanders, children, and visitors away
while operating the tool. Distractions are
able to result in the loss of control of the tool.

Page 3;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 60801 60802
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
J*(#&8,7%E,2*$[
1. Stay alert. Watch what you are doing and
use common sense when operating the tool.
Do not use the tool while tired or under the
influence of drugs, alcohol, or medication.%%
A moment of inattention while operating the
tool increases the risk of injury to persons.
2. U(*##%/(&/*(7[1%%U&%8&$%)*,(%7&&#*%
47&$."83%&(%Z*)*7([1%%O&8$,"8%7&83%.,"(1%%
V**/%.,"(=%47&$."83=%,89%37&]*#%,),[%2(&5%
5&]"83%/,($#1%%Loose clothes, jewelry, or long
hair increases the risk of injury to persons as
a result of being caught in moving parts.
3. F]&"9%'8"8$*8$"&8,7%#$,($"831%%S*%#'(*%$.*%#)"$4.%
"#%&22%+*2&(*%4&88*4$"83%$&%$.*%,"(%#'//7[1%%
Do not carry the tool with your finger on the switch or
connect the tool to the air supply with the switch on.
4. U&%8&$%&]*((*,4.1%%%
V**/%/(&/*(%2&&$"83%,89%+,7,84*%,$%,77%$"5*#1%%
Proper footing and balance enables better
control of the tool in unexpected situations.
5. P#*%#,2*$[%*<'"/5*8$1
A dust mask, non-skid safety shoes
and a hard hat must be used for the
applicable conditions.
6. F7),[#%)*,(%*[*%/(&$*4$"&81
Wear ANSI-approved safety goggles.
7. F7),[#%)*,(%.*,("83%%
% /(&$*4$"&8%).*8%'#"83%$.*%$&&71
Prolonged exposure to high
intensity noise is able
to cause hearing loss.
8. Q*,(%.*,][?9'$[%)&(Y%37&]*#%9'("83%'#*1
G&&7%P#*%,89%O,(*
1. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against the body is
unstable and is able to lead to loss of control.
2. U&%8&$%2&(4*%$.*%$&&71 Use the correct tool for the
application. The correct tool will do the job better
and safer at the rate for which the tool is designed.
3. U&%8&$%'#*%$.*%$&&7%"2%$.*%#)"$4.%9&*#%
8&$%$'(8%$.*%$&&7%&8%&(%&221 Any tool that
cannot be controlled with the switch is
dangerous and must be repaired.
4. U"#4&88*4$%$.*%$&&7%2(&5%$.*%,"(%#&'(4*%+*2&(*%
5,Y"83%,8[%,9Z'#$5*8$#=%4.,83"83%,44*##&("*#=%
&(%#$&("83%$.*%$&&71 Such preventive safety
measures reduce the risk of starting the tool
unintentionally. Turn off and detach the air supply,
safely discharge any residual air pressure, and
release the throttle and/or turn the switch to its
off position before leaving the work area.
5. Store the tool when it is idle out of reach
of children and other untrained persons.
A tool is dangerous in the hands of untrained users.
6. N,"8$,"8%$.*%$&&7%)"$.%4,(*1%%%
A properly maintained tool is easier to control.
7. O.*4Y%2&(%5"#,7"385*8$%&(%+"89"83%&2%5&]"83%
/,($#=%+(*,Y,3*%&2%/,($#=%,89%,8[%&$.*(%4&89"$"&8%
$.,$%,22*4$#%$.*%$&&7^#%&/*(,$"&81%%If damaged,
have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
There is a risk of bursting if the tool is damaged.
8. P#*%&87[%,44*##&("*#%$.,$%,(*%"9*8$"2"*9%+[%$.*%
5,8'2,4$'(*(%2&(%$.*%#/*4"2"4%$&&7%5&9*71 Use of
an accessory not intended for use with the specific
tool model, increases the risk of injury to persons.
E*(]"4*
1. Tool service must be performed only
by qualified repair personnel.
2. Q.*8%#*(]"4"83%,%$&&7=%'#*%&87[%"9*8$"4,7%
(*/7,4*5*8$%/,($#1%%P#*%&87[%,'$.&("_*9%/,($#1
3. P#*%&87[%$.*%7'+("4,8$#%#'//7"*9%)"$.%$.*%$&&7%&(%
#/*4"2"*9%+[%$.*%5,8'2,4$'(*(1%%%
Do not use any lubricants with this tool.

Page 4 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 60801 60802
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
F"(%E&'(4*
1. M*]*(%4&88*4$%$&%,8%,"(%#&'(4*%%
% $.,$%"#%4,/,+7*%&2%*\4**9"83%%
% `aa%/#"1 Over pressurizing the
tool may cause bursting, abnormal
operation, breakage of the tool or
serious injury to persons. Use only clean, dry,
regulated compressed air at the rated pressure
or within the rated pressure range as marked on
the tool. Always verify prior to using the tool that
the air source has been adjusted to the rated air
pressure or within the rated air-pressure range.
2. Never use oxygen, carbon dioxide, combustible
gases or any bottled gas as an air source
for the tool. Such gases are capable of
explosion and serious injury to persons.
%EF!6%GW6E6%LMEGKPOGLIME1
EHNSITE%FMU%EJ6OL;LO%EF;6GH%LMEGKPOGLIME
E[5+&7%U*2"8"$"&8#
E[5+&7 J(&/*($[%&(%#$,$*5*8$
JEL Pounds per square inch of pressure
O;N Cubic Feet per Minute flow
EO;N Cubic Feet per Minute flow
at standard conditions
MJG National pipe thread, tapered
MJE National pipe thread, straight
E[5+&7 J(&/*($[%&(%#$,$*5*8$
WARNING marking
concerning Risk of Eye Injury.
Wear ANSI-approved eye protection.
WARNING marking concerning Risk of
Hearing Loss. Wear hearing protection.
WARNING marking concerning
Risk of Respiratory Injury. Wear
NIOSH-approved dust mask/respirator.
WARNING marking concerning
Risk of Explosion.
E/*4"2"4%E,2*$[%L8#$('4$"&8#
1. The warnings and precautions discussed in this
manual cannot cover all possible conditions and
situations that may occur. It must be understood
by the operator that common sense and caution
are factors which cannot be built into this
product, but must be supplied by the operator.
2. UI%MIG%UKIJ%GFMV=%KLEV%I;%6bJTIELIM1
3. Attach all accessories properly to the Soda Blaster
before connecting the air supply. A loose
accessory may detach or break during operation.
4. Obey the manual for the air compressor
used to power this Soda Blaster.
5. Install an in-line shutoff valve to allow
immediate control over the air supply in an
emergency, even if a hose is ruptured.

Page 5;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 60801 60802
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
E"7"4&#"#%,89%F7'5"8'5%I\"9*%Q,(8"83#
QFKMLMRc%Abrasive blasting with sand containing
crystalline silica can cause serious or fatal respiratory
disease. Exposure to crystalline silica may cause
silicosis (a serious lung disease), cancer and death.
Exposure to aluminum oxide (a dust generated from
material removing processes) can result in eye, skin
and breathing irritation. Always use a NIOSH (National
Institute for Occupational Safety and Health) approved
respirator and safety goggles. Avoid skin exposure.
Proper ventilation in the work area is required. Read
and understand the 10 recommended measures below
to reduce crystalline silica exposures in the workplace
and prevent silicosis and silicosis related deaths.
MLIEW%(*4&55*89#%$.*%2&77&)"83%5*,#'(*#%$&%
(*9'4*%4([#$,77"8*%#"7"4,%*\/&#'(*#%"8%$.*%)&(Y/7,4*%
,89%/(*]*8$%#"7"4&#"#%,89%#"7"4&#"#?(*7,$*9%9*,$.#-
1. Prohibit silica sand (or other substances
containing more than 1% crystalline silica)
as an abrasive blasting material and
substitute less hazardous materials.
2. Conduct air monitoring to measure
worker exposures.
3. Use containment methods such as blast-cleaning
machines and cabinets to control the hazard
and protect adjacent workers from exposure.
4. Practice good personal hygiene to avoid
unnecessary exposure to silica dust.
5. Wear washable or disposable protective clothes
at the work site. Shower and change into clean
clothes before leaving the work site to prevent
contamination of cars, homes and other work areas.
6. Use respiratory protection when source controls
cannot keep silica exposures below the NIOSH REL.
7. Provide periodic medical examinations for all
workers who may be exposed to crystalline silica.
8. Post signs to warn workers about the hazard and to
inform them about required protective equipment.
9. Provide workers with training that includes
information about health effects, work practices
and protective equipment for crystalline silica.
10. Report all cases of silicosis to State health
departments and to OSHA or the Mine Safety
and Health Administration (MSHA).
!"+(,$"&8%J(*4,'$"&8#
This tool vibrates during use. Repeated or
long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders. To
reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for
an extended period should first be examined
by a doctor and then have regular medical
check-ups to ensure medical problems are not
being caused or worsened from use. Pregnant
women or people who have impaired blood
circulation to the hand, past hand injuries,
nervous system disorders, diabetes, or Raynaud's
Disease should not use this tool. If you feel
any symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
7. To reduce vibration, maintain
tool as explained in this manual.
If abnormal vibration occurs, stop immediately.
%EF!6%GW6E6%LMEGKPOGLIME1

Page 6 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 60801 60802
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
;PMOGLIMFT%U6EOKLJGLIM
E/*4"2"4,$"&8#
LG6N Aa@a> Aa@a`
Maximum Air Pressure 90 PSI
Air Inlet 1/4″ -18 NPT
Average Air Consumption 8.5 CFM @ 90 PSI 7 CFM @ 90 PSI
Abrasive Capacity 40 lb. 15 lb.
Abrasive Type Sodium Bicarbonate media &87[
O&5/&8*8$#%,89%O&8$(&7#
G,8Y
F"(%!,7]*
F"(%
K*3'7,$&(
V8&+
N*9",%
K*3'7,$&(
V8&+
N*9",%
!,7]*
E,2*$[%
!,7]*
J(*##'(*%
R,'3*
M&__7*

Page 7;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 60801 60802
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
LMLGLFT%EIUF%STFEG6K%E6G%PJ0FEE6NSTH
%K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*\$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
M&$*- For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
F##*5+7[
1. Wrap the threads of the Pressure Gauge (7)
with thread sealer tape (not included). Screw the
Pressure Gauge into the opening in the face of the
Air Regulator (9). Tighten using a wrench on the
back of the Gauge block. U&%8&$%&]*($"3.$*81
2. Attach Bracket (3) to the Tank (1) using the two
Socket Head Screws (4) and wrench tighten.
3. Remove the Compression Nut (2)
from the Air Regulator (9).
4. Insert the knob on the top of the
Air Regulator (9) through the Bracket (3).
5. Align the tab on the Bracket with the recess
at gauge side of the Regulator, attach
Compression Nut (2), and finger tighten until snug.
S(,4Y*$%def
E&4Y*$%W*,9%
E4(*)#%dgf
J(*##'(*%
R,'3*%dCf
F"(%
K*3'7,$&(%dDf
O&5/(*##"&8%
M'$%d`f
G,8Y%d>f
;"3'(*%F-%%F"(%K*3'7,$&(%F##*5+7[
F"(%E'//7[
GI%JK6!6MG%E6KLIPE%LMXPKH%;KIN%6bJTIELIM-%
P#*%&87[%47*,8=%9([=%(*3'7,$*9=%4&5/(*##*9%,"(%$&%/&)*(%$."#%E&9,%S7,#$*(1%%%
U&%8&$%'#*%&\[3*8=%4,(+&8%9"&\"9*=%4&5+'#$"+7*%3,#*#=%%
&(%,8[%&$.*(%+&$$7*9%3,#%,#%,%/&)*(%#&'(4*%2&(%$."#%E&9,%S7,#$*(1
1. Incorporate a filter, regulator with pressure
gauge, dryer, in-line shutoff valve, and quick
coupler for best service. %F8%"8?7"8*%#.'$&22%+,77%
],7]*%"#%,8%"5/&($,8$%#,2*$[%9*]"4*%+*4,'#*%
"$%4&8$(&7#%$.*%,"(%#'//7[%*]*8%"2%$.*%,"(%.&#*%
"#%('/$'(*91%%G.*%#.'$&22%],7]*%#.&'79%+*%,%
+,77%],7]*%+*4,'#*%"$%4,8%+*%47&#*9%<'"4Y7[1
M&$*-%An oiler system should not be used with
this Soda Blaster. The oil will mix with the
material being propelled, causing poor results.
2. Attach an air hose to the compressor's air outlet.
Connect the air hose to the air valve
of the Soda Blaster. Other components, such
as a coupler plug and quick coupler, will make
operation more efficient, but are not required.
M&$*-%Air flow, and therefore Soda Blaster
performance, can be hindered by undersized air
supply components. The air hose must be long
enough to reach the work area with enough extra
length to allow free movement while working.
3. Close the Soda Blaster’s valves.
4. Close the in-line shutoff valve between the
compressor and the Soda Blaster.
5. Turn on the air compressor according to
the manufacturer's directions and allow it
to build up pressure until it cycles off.
6. Adjust the air compressor's output regulator so
that the air output is enough to properly power the
Soda Blaster, but the output will not exceed the
Soda Blaster's maximum air pressure at any time.
Adjust the pressure gradually, while checking the
air output gauge to set the right pressure range.
7. Inspect the air connections for leaks.
Repair any leaks found.
8. If the Soda Blaster will not be used at this
time, turn off and detach the air supply, safely
discharge any residual air pressure, and close
the valves to prevent accidental operation.

Page 8 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 60801 60802
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
IJ6KFGLMR%LMEGKPOGLIME
%K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*\$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
L8#/*4$%E&9,%S7,#$*(%+*2&(*%'#*=%7&&Y"83%2&(%9,5,3*9=%7&&#*=%,89%5"##"83%/,($#1%%
L2%,8[%/(&+7*5#%,(*%2&'89=%9&%8&$%'#*%E&9,%S7,#$*(%'8$"7%(*/,"(*91
G&&7%E*$%P/%?%T&,9"83%F+(,#"]*
GI%JK6!6MG%E6KLIPE%LMXPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
O7&#*%,77%!,7]*#=%9*$,4.%$.*%,"(%#'//7[=%#,2*7[%9"#4.,(3*%,8[%(*#"9',7%,"(%/(*##'(*%"8%$.*%E&9,%S7,#$*(=%%
,89%47&#*%,77%!,7]*#%,3,"8%+*2&(*%/*(2&(5"83%,8[%/(&4*9'(*%"8%$."#%#*4$"&81
GI%JK6!6MG%E6KLIPE%LMXPKH-%
U&%8&$%,9Z'#$%&(%$,5/*(%)"$.%,8[%4&8$(&7%&(%4&5/&8*8$%"8%,%),[%8&$%#/*4"2"4,77[%*\/7,"8*9%)"$."8%
$."#%5,8',71%%L5/(&/*(%,9Z'#$5*8$%4,8%(*#'7$%"8%E&9,%S7,#$*(%2,"7'(*%&(%&$.*(%#*("&'#%.,_,(9#1
P#*%#&9"'5%+"4,(+&8,$*%+7,#$%5*9",%&87[1
QFKMLMRc%%GI%JK6!6MG%E6KLIPE%
LMXPKH-%%U&%8&$%'#*%#,89%&(%&$.*(%+7,#$"83%
5,$*(",7#%$.,$%4&8$,"8%4([#$,77"8*%#"7"4,1
M&$*- Use only dry and clean abrasives
to avoid clogging the Soda Blaster.
M&$*- The Nozzle size depends on grit of media used.
Change the nozzle as needed to suit the abrasive.
1. Pull back on the blue Air Hose Connector (8)
collar and pull out Air Hose (15).
2. Hold collar on Tank (1) with a wrench and use
another wrench to loosen Bushing (10).
(Wrenches not included.)
3. Remove entire media discharge assembly slowly,
being careful with the Pickup Tube (11) as it may
contain residual media which can spill when
removed. Allow time for the trapped aggregate
to safely discharge back into the Tank.
4. Using a funnel, pour media into the Tank.
M&$*- If this is a large job, fill the Tank only
3/4 full and reload as needed to finish the job.
M&$*- If the humidity is 90 to 100%, reduce the amount
of media and refill more frequently to reduce clogging.
5. Inspect condition of the O-ring (19) at the bottom
of the Bushing, and replace if damaged.
6. Insert the Pickup Tube into the Tank and
tighten the Bushing. U&%8&$%&]*(%$"3.$*81
7. Pull back on the blue Air Hose Connector
collar and insert the Air Hose deep into the
fitting. Release the collar.
M&$*- If air leaks around the Air Hose, remove it,
cut approximately a quarter of an inch off and reattach it.
8. Turn on the compressor and set the
regulator to the pressure recommended
for this Soda Blaster (90 PSI).
OFPGLIMc%%U&%8&$%*\4**9%Da%JEL1

Page 9;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 60801 60802
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
Q&(Y/"*4*%,89%Q&(Y%F(*,%E*$%P/
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
2. Route the air hose along a safe route to reach
the work area without creating a tripping hazard
or exposing the air hose to possible damage.
The air hose must be long enough to reach
the work area with enough extra length to
allow free movement while working.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be hazardous objects
(such as utility lines or foreign objects) nearby
that will present a hazard while working.
R*8*(,7%I/*(,$"83%L8#$('4$"&8#
1. If possible, place the workpiece inside a
sandblast cabinet. Otherwise, isolate the
workpiece to make sure no damage can
occur to nearby personal property.
2. Open the Air Valve.
3. Grip the Media Hose and Nozzle firmly,
and point them at the start point. Open the
Media Valve completely to release the media.
MIGLO6- To prevent damage, only use
the Media Valve to turn the flow on or off.
Do not use it to adjust the flow rate. Only use the
Media Regulator Knob to adjust the flow rate.
4. Spray the abrasive media onto the work material,
moving the Nozzle from side to side.
MIG6- The flow rate of the media may be irregular
when first started. Provided the media is dry,
the flow rate will normalize in approximately one minute.
5. Use Media Regulator Knob to
adjust the media flow rate.
6. Adjust the Air Regulator to adjust the
air flow and pressure. Do not set the
pressure higher than 90 PSI.
7. If the Soda Blaster requires more force to
accomplish the task, verify that the Soda Blaster
receives sufficient, unobstructed airflow (CFM) and
increase the pressure (PSI) output of the regulator
up to the maximum air pressure rating of this
Soda Blaster.
OFPGLIMc%%GI%JK6!6MG%EIUF%STFEG6K%FMU%
FOO6EEIKH%;FLTPK6=%K6EPTGLMR%LM%LMXPKH-%
U&%8&$%*\4**9%$.*%E&9,%S7,#$*(h#%5,\"5'5%,"(%
/(*##'(*%(,$"831
If the Soda Blaster still does not have sufficient
force at maximum pressure and sufficient airflow,
then a larger Soda Blaster may be required.
8. If excessive air pressure is used, or Media Regulator
becomes clogged, the Safety Valve may open,
releasing air pressure. To correct:
a. Shut OFF Air Valve.
b. Adjust Air Regulator to below 90 PSI.
c. Turn the Air Valve back on.
d. If the problem happens again,
detach the air supply and clean out the
Media Regulator and Media Hose.
9. To prevent accidents, close the Valves on the
Soda Blaster, detach the air supply, safely
discharge any residual air pressure in the
Soda Blaster, and close the Valves again. Empty
the Tank, and clean external surfaces of the
Soda Blaster with clean, dry cloth. Then store the
Soda Blaster indoors out of children’s reach.

Page 10 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 60801 60802
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
PE6K?NFLMG6MFMO6%LMEGKPOGLIME
%J(&4*9'(*#%8&$%#/*4"2"4,77[%*\/7,"8*9%"8%$."#%5,8',7%5'#$%
+*%/*(2&(5*9%&87[%+[%,%<',7"2"*9%$*4.8"4",81
GI%JK6!6MG%E6KLIPE%LMXPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
G'(8%&22%$.*%E&9,%S7,#$*(=%9*$,4.%$.*%,"(%#'//7[=%#,2*7[%9"#4.,(3*%,8[%(*#"9',7%,"(%
/(*##'(*%"8%$.*%E&9,%S7,#$*(=%,89%(*7*,#*%$.*%$.(&$$7*%,890&(%$'(8%$.*%#)"$4.%$&%"$#%&22%
/&#"$"&8%+*2&(*%/*(2&(5"83%,8[%"8#/*4$"&8=%5,"8$*8,84*=%&(%47*,8"83%/(&4*9'(*#1
GI%JK6!6MG%E6KLIPE%LMXPKH%;KIN%EIUF%STFEG6K%;FLTPK6-%
U&%8&$%'#*%9,5,3*9%*<'"/5*8$1%%L2%,+8&(5,7%8&"#*=%]"+(,$"&8=%
&(%7*,Y"83%,"(%&44'(#=%.,]*%$.*%/(&+7*5%4&((*4$*9%+*2&(*%2'($.*(%'#*1
O7*,8"83=%N,"8$*8,84*=%,89%T'+("4,$"&8
M&$*- These procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the air-operated Soda Blaster.
1. S6;IK6%6FOW%PE6= inspect the general
condition of the Soda Blaster. Check for:
• loose hardware or housing,
• misalignment or binding of moving parts,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
2. U,"7[%?%F"(%E'//7[%N,"8$*8,84*-%
Every day, maintain the air supply according
to the component manufacturers' instructions.
Drain the moisture filter regularly.
Performing routine air supply maintenance will
allow the Soda Blaster to operate more safely
and will also reduce wear on the Soda Blaster.
G(&'+7*#.&&$"83
1. Excess moisture will cause the abrasive to slow
or stop flowing through the Abrasive Outlet Pipe.
To test, check the abrasive by pouring a 6″ cone
of abrasive on dry newspaper. After several
minutes, remove the abrasive from the newspaper.
Do not use the abrasive if the newspaper is moist.
2. Poor or irregular flow of the abrasive may also be
due to low air pressure or a worn Nozzle.
To correct, increase the air pressure
(to no more than 90 PSI) and/
or replace the worn Nozzle.

Page 11;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 60801 60802
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
JFKGE%TLEG%FMU%ULFRKFN
JT6FE6%K6FU%GW6%;ITTIQLMR%OFK6;PTTH
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
K*4&(9%J(&9'4$^#%E*(",7%M'5+*(%W*(*-%
M&$*- If product has no serial number, record month and year of purchase instead.
M&$*- Some parts are listed and shown for illustration purposes only, and are not available individually
as replacement parts. Parts may not be interchangeable. Specify UPC number when ordering:
40 lb. (60801): 792363608015
15 lb. (60802): 792363608022
J,($ U*#4("/$"&8 i$[
1 Tank 1
2 Compression Nut 1
3 Bracket 1
4 Socket Head Screw 2
5 Male Coupler 1
6 Air Valve 1
7 Pressure Gauge 1
8 Air Hose Connector 2
9 Air Regulator 1
10 Bushing 1
J,($ U*#4("/$"&8 i$[
11 Pickup Tube 1
12 Media Valve 1
13 Media Regulator Asm. 1
14 Safety Valve 1
15 Air Hose 1
16 Media Hose 1
17 Nozzle Capnut 1
18 Ceramic Nozzle 1
19 O-Ring 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
8
19

TLNLG6U%Da%UFH%QFKKFMGH
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
`ABg>%F3&'(,%K&,9%%j%%O,7,+,#,#=%OF%D>ea`%%j%%>?@@@?@AA?BCDC