Hatco LW-2 User manual

Portable amp Warmer
W Series
Installation and Operating Manual
P/N 07.04.277.00
© 2012 atco Corporation
Register Online!
(see page 2)
www.hatcocorp.com
Do not operate this equipment unless you
have read and understood the contents of
this manual! Failure to follow the
instructions contained in this manual may
result in serious injury or death. This
manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en este
manual puede resultar en un serio lesión
o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted no
puede entender el contenido de este
manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel !
e non-respect des instructions
contenues dans ce manuel peut entraîner
de graves blessures ou la mort. Ce
manuel contient des informations
importantes concernant l'entretien,
l'utilisation et le fonctionnement de ce
produit. Si vous ne comprenez pas le
contenu de ce manuel, veuillez le signaler
à votre supérieur. Conservez ce manuel
dans un endroit sûr pour pouvoir vous y
référer plus tard.
WARNING
ADVERTENCIA
AVERTISSEMENT

CONTENTS
2Form No. LWM-0512
Important Owner Information ..............................................2
Introduction...........................................................................2
Important Safety Information...............................................3
Model Description.................................................................4
Model Designation................................................................4
Specifications........................................................................5
Plug Configuration...............................................................5
Electrical Rating Chart ........................................................5
Dimensions .........................................................................5
Installation.............................................................................6
General ...............................................................................6
Operation...............................................................................7
General ...............................................................................7
Maintenance ..........................................................................8
General ...............................................................................8
Daily Cleaning .....................................................................8
Replacing a eat Bulb ........................................................8
Troubleshooting Guide ........................................................9
Options and Accessories...................................................10
imited Warranty.................................................................11
Authorized Parts Distributors............................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number (specification label
located on the back of the unit), voltage, and purchase date of
the unit in the spaces below. Please have this information
available when calling atco for service assistance.
Model No. ____________________________________
Serial No. ____________________________________
Voltage ______________________________________
Date of Purchase ______________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the atco website at
www.hatcocorp.com, select the Parts & Service pull-down
menu, and click on “Warranty Registration”.
Business 8:00 AM to 5:00 PM
ours: Central Standard Time (C.S.T.)
(Summer ours: June to September –
8:00 AM to 5:00 PM C.S.T.
Monday through Thursday
8:00 AM to 2:30 PM C.S.T. Friday)
Telephone: [phone]
E-mail: part[email protected]
Fax: [phone] (Parts and Service)
[phone] (International)
Additional information can be found by visiting our web site at
www.hatcocorp.com.
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling [phone].
INTRODUCTION
atco Portable Lamp Warmers are designed to hold your food
products at serving temperatures without affecting quality. The
specially designed stand keeps food holding pans above the
countertop, providing insulation for extended holding times.
Portable Lamp Warmers are quality built to meet the demands
of foodservice operations and provide years of trouble-free
performance.
atco Portable Lamp Warmers are products of extensive
research and field testing. The materials used were selected
for maximum durability, attractive appearance, and optimum
performance. Every unit is inspected and tested thoroughly
prior to shipment.
This manual provides the installation, safety, and operating
instructions for Portable Lamp Warmers. atco recommends
all installation, operating, and safety instructions appearing in
this manual be read prior to installation or operation of a unit.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
personal injury.
WARNING
NOTICE
CAUTION

IMPORTANT SAFETY INFORMATION
Form No. LWM-0512 3
E ECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• Unit is not weatherproof. ocate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by Hatco, an Authorized
Hatco Service Agent, or a person with similar
qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: ocate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
WARNING
Hatco Corporation is not responsible for the actual food
product serving temperature. It is the responsibility of the
user to ensure that the food product is held and served at
a safe temperature.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from unit.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at 800-558-
0607 or 414-671-6350; fax [phone]; or International fax
414-671-3976.
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
ocate unit at the proper counter height in an area that is
convenient for use. ocation should be level and strong
enough to support weight of unit and contents.
Damage to any countertop material caused by heat
generated from Hatco equipment is not covered under the
Hatco warranty. Contact the manufacturer of the
countertop material for application information.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring
its appearance and making it susceptible to soil
accumulation.
Do not use ammonia-based cleaners on unit.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
NOTICE
CAUTION
WARNING
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.

MODE DESCRIPTION
MODE DESIGNATION
4Form No. LWM-0512
All Models
The Portable Lamp Warmer is specially designed to give long
lasting, trouble-free service. The warmer incorporates a
specially designed stand that keeps food holding pans above
the countertop, providing an effective insulation to prolong
serving times.
Portable Lamp Warmers have powdercoated lamp shades and
an adjustable stand that allows you to vary the height from
10-1/2–16-1/2" (267–419 mm) above the product. The base
holds full size and half-size pans (not included).
The unit comes with vented metal lamp shades with heavy duty
sockets, two uncoated 250 watt bulbs, and a 6' (1829 mm) cord
and plug with an in-line ON/OFF switch. The warmer is
available in several powdercoated Designer colors.
NOTE: Refer to the OPTIONSAND ACCESSORIES section in
this man al for additional feat res.
LW-2 Model
ON/OFF
Switch
L W - 2
Lamp Warmer Quantity of Heat Lamps

Model Voltage Watts Amps Plug Configuration Shipping Weight
LW-2 120 500 4.2 NEMA 5-15P 18 lbs. (8 kg)
220–230 (CE) 457–500 2.1–2.2 CEE 7/7 Schuko 18 lbs. (8 kg)
230–240 (CE) 500–544 2.2–2.3 BS 1363 18 lbs. (8 kg)
Model
Width
(A)
Depth
(B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
Clearance
(F)
LW-2 12-3/8″
(314 mm)
21-5/8″
(548 mm)
24-3/8–30-3/8″
(618–770 mm)
12″
(305 mm)
19-5/8″
(498 mm)
10-1/2–16-1/2″
(267–419 mm)
SPECIFICATIONS
Form No. LWM-0512 5
Electrical Rating Chart
The shaded areas contain electrical information for International models only.
Dimensions
Front View Side View
A
C
D
B
E
F
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug installed. Plugs are supplied according to the applications.
E ECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of correct voltage, size, and
plug configuration. If plug and receptacle do not match,
contact a qualified electrician to determine and install
proper voltage and size electrical receptacle.
NOTE: Specification label located on the back of the nit. See
label for serial n mber and verification of nit electrical
information.
WARNING
Plug Configurations
NOTE: Receptacles are not s pplied by Hatco.
NEMA 5-15P
CEE 7/7 Schuko
BS-1363

INSTA ATION
6Form No. LWM-0512
General
Use the following information and procedures to install a
Portable Lamp Warmer.
E ECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Unit is not weatherproof. ocate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
FIRE HAZARD:
• ocate unit a minimum of 1″ (25 mm) from combustible
walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
ocate unit at the proper counter height in an area that is
convenient for use. ocation should be level and strong
enough to support weight of unit and contents.
Damage to any countertop material caused by heat
generated from Hatco equipment is not covered under the
Hatco warranty. Contact the manufacturer of the
countertop material for application information.
NOTICE
CAUTION
WARNING
1. Remove the unit from the carton.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape and protective packaging from all surfaces
of the unit.
3. Place the unit in the desired location.
4. Place food pans into base of unit.
5. Adjust the lamps to the desired height.
a. Remove the height adjustment screw from the lamp
post.
b. Move the lamp post to the desired position. There are
four adjustment positions in increments of 2” (51 mm).
c. Align the adjustment screw with the hole at one of the
four positions. Tighten securely.
Lamp eight Adjustment
Height
Adjustment
Screw
Adjustment
Positions

OPERATION
Form No. LWM-0512 7
General
Use the following procedure to operate a Portable Lamp
Warmer.
Read all safety messages in the Important Safety
Information section before operating this equipment.
Hatco Corporation is not responsible for the actual food
product serving temperature. It is the responsibility of the
user to ensure that the food product is held and served at
a safe temperature.
Startup
1. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
2. Move the ON/OFF switch to the ON position.
• The ON/OFF switch is located on the electrical cord.
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
WARNING
CAUTION
ON/OFF
Switch
Shutdown
1. Move the ON/OFF switch to the OFF position.
2. Perform the “Daily Cleaning” procedure in the
MAINTENANCE section of this manual.

MAINTENANCE
8Form No. LWM-0512
General
Portable Lamp Warmers are designed for maximum durability
and performance, with minimum maintenance.
E ECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax [phone]; or
International fax [phone].
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring
its appearance and making it susceptible to soil
accumulation.
Do not use ammonia-based cleaners on unit.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Daily Cleaning
To preserve the finish of the unit, it is recommended that all
surfaces be wiped daily with a non-abrasive, damp cloth.
1. Move the ON/OFF switch to the OFF position and allow
the unit to cool completely.
2. Wipe down the entire unit with a clean, non-abrasive,
water-dampened cloth. Stubborn stains can be removed
with a mild, non-abrasive cleanser.
3. Wipe dry the entire unit using a clean, non-abrasive cloth.
NOTICE
WARNING
Replacing a Heat Bulb
Each standard wattage Portable Lamp Warmer holds two
infrared heat bulbs rated at 250 W.
Use only Genuine Hatco Replacement Parts when service
is required. Failure to use Genuine Hatco Replacement
Parts will void all warranties and may subject operators of
the equipment to hazardous electrical voltage, resulting in
electrical shock or burn. Genuine Hatco Replacement Parts
are specified to operate safely in the environments in which
they are used. Some aftermarket or generic replacement
parts do not have the characteristics that will allow them
to operate safely in Hatco equipment.
1. To replace a bulb, move the ON/OFF switch in the OFF
position and allow the bulbs to cool completely.
2. Bulbs have a threaded base. Unscrew the heat bulb from
the unit and replace with new bulb.
NOTE: Refer to the OPTIONSANDACCESSORIES section
for replacement heat b lbs available from Hatco.
Replacing a eat Bulb
WARNING
ON/OFF
Switch
Heat
Bulb

Symptom Probable Cause Corrective Action
Unit is not working at all. Unit not turned on. Move ON/OFF switch to the ON position.
ON/OFFswitch is not functioning. Contact Authorized Service Agent or atco for assistance.
Bulbs have burned out. Replace bulbs.
Unit is turned on but there is no
light.
No power to unit. Check circuit breaker and reset as necessary.
Switch is defective. Contact Authorized Service Agent or atco for assistance.
Bulbs have burned out. Replace bulbs.
eat is inadequate. Lights are too high above target
area.
Lower unit, putting effective heat closer to target. See the
INSTALLATION section for details.
Excessive air movement around
heating area.
Restrict or redirect air movement (i.e. air conditioning duct
or exhaust fan) away from unit.
Incorrect heat bulb wattage. Verify heat bulb wattage and replace with the correct
wattage bulb. WARNING! DONOT exceed maximum
bulb wattage rating on specification plate.
Incorrect power supply (low). Check power supply to unit, making sure it matches rating
on the unit. If power supply is incorrect, change to match
rating on unit.
eat is excessive. Lights are too close to target area. Raise unit, putting effective heat farther from target area.
See the INSTALLATION section for details.
eat bulb wattage too high. Check bulb wattage and replace with correct wattage bulb.
Voltage supply too high. Check power supply to unit, making sure it matches rating
on unit. If power supply is incorrect, change to match
rating.
TROUB ESHOOTING GUIDE
Form No. LWM-0512 9
This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
WARNING
E ECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
WARNING

OPTIONS AND ACCESSORIES
10 Form No. LWM-0512
Food Holding Pans
The following stainless steel food holding pans are available for
Portable Lamp Warmers.
Full Size Pans........................12-3/4”W x 20-3/4”D x 4”
(324 mm x 527 mm x 102 mm)
Half-Size Pans .......................12-3/4”W x 10-3/8”D x 4”
(324 mm x 264 mm x 102 mm)
Third-Size Pans .....................12-3/4”W x 6-7/8”D x 4”
(324 mm x 175 mm x 102 mm)
Infrared Heat Bulbs
The following infrared heat bulbs are available for use in atco
Portable Lamp Warmers.
120 V, 250 W, Clear, Coated 02.30.069.00
120 V, 250 W, Clear, Uncoated 02.30.071.00
120 V, 250 W, Red, Coated 02.30.068.00
120 V, 250 W, Red, Uncoated 02.30.070.00
240 V, 250 W, Clear, Coated 02.30.100.00
240 V, 250 W, Clear, Uncoated 02.30.083.00
5 Pleat French Fry Box Ribbon
A five pleat hardcoated french fry box ribbons is available as an
accessory to hold french fry boxes.
Five Pleat Fry Box Ribbon
8 Pleat French Fry Bag Ribbon
An eight pleat hardcoated french fry bag ribbon is available as
an accessory to hold french fry bags.
Eight Pleat Fry Bag Ribbon

IMITED WARRANTY
Form No. LWM-0512 11
1. PRODUCT WARRANTY
atco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a period of
one (1) year from the date of purchase when installed and
maintained in accordance with atco’s written instructions or
18 months from the date of shipment from atco. Buyer must
establish the Product’s purchase date by registering the
Product with atco or by other means satisfactory to atco in
its sole discretion.
atco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and abor P US One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip eater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
olding Cabinet Elements (metal sheathed air heating)
eated Well Elements — WB Series (metal sheathed)
b) One (1) Year Parts and abor P US Four (4) Years
Parts-Only Warranty on pro-rated terms that Hatco
will explain at Buyer’s request:
3CS and FR Tanks
c) One (1) Year Parts and abor P US Nine (9) Years
Parts-Only Warranty on:
Electric Booster eater Tanks
Gas Booster eater Tanks
d) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
T E FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ANY OT ER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERC ANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR PATENT OR OT ER
INTELLECTUAL PROPERTY RIG T INFRINGEMENT.
Without limiting the generality of the foregoing, SUC
WARRANTIES DO NOT COVER: Coated incandescent light
bulbs, fluorescent lights, heat lamp bulbs, coated halogen light
bulbs, halogen heat lamp bulbs, xenon light bulbs, LED light
tubes, glass components, and fuses; Product failure in booster
tank, fin tube heat exchanger, or other water heating equipment
caused by liming, sediment buildup, chemical attack, or
freezing; or Product misuse, tampering or misapplication,
improper installation, or application of improper voltage.
2. IMITATION OF REMEDIES AND DAMAGES
atco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at atco’s option, to repair or replacement
using new or refurbished parts or Product by atco or a atco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case atco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. atco reserves
the right to accept or reject any such claim in whole or in part.
In the context of this Limited Warranty, “refurbished” means a
part or Product that has been returned to its original
specifications by atco or a atco-authorized service agency.
atco will not accept the return of any Product without prior
written approval from atco, and all such approved returns shall
be made at Buyer’s sole expense. ATCO WILL NOT BE
LIABLE, UNDER ANY CIRCUMSTANCES, FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING
BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS
RESULTING FROM T E USE OF OR INABILITY TO USE T E
PRODUCTS OR FROM T E PRODUCTS BEING
INCORPORATED IN OR BECOMING A COMPONENT OF
ANY OT ER PRODUCT OR GOODS.

Printed in U.S.A. May 2012 P/N 07.04.277.00 Form No. LWM-0512
HATCO CORPORATION
P.O. Box 340500
Milwaukee, WI 53234-0500 U.S.A.
[phone] [phone]
Parts and Service Fax [phone]
International Fax [phone]
[email protected]
www.hatcocorp.com
HATCO AUTHORIZED PARTS DISTRIBUTORS
Register your unit online!
See IMPORTANT OWNER INFORMATION
section for details.
A ABAMA
Jones McLeod Appl. Svc.
Birmingham 205-251-0159
ARIZONA
Service Solutions Group
Phoenix 602-234-2443
Byassee Equipment Co.
Phoenix 602-252-0402
CA IFORNIA
Industrial Electric
Commercial Parts & Service, Inc.
untington Beach 714-379-7100
Chapman Appl. Service
San Diego 619-298-7106
P & D Appliance
Commercial Parts & Service, Inc.
S. San Francisco 650-635-1900
CO ORADO
awkins Commercial Appliance
Englewood 303-781-5548
F ORIDA
Whaley Foodservice Repair
Jacksonville 904-725-7800
3Wire Nass Service Co., Inc.
Orlando 407-425-2681
B.G.S.I.
Pompano Beach 954-971-0456
Comm. Appliance Service
Tampa 813-663-0313
GEORGIA
TWC Services
Mableton 770-438-9797
eritage Service Group
Norcross 866-388-9837
Southeastern Rest. Svc.
Norcross 770-446-6177
HAWAII
Burney’s Comm. Service, Inc.
onolulu 808-848-1466
Food Equip Parts & Service
onolulu 808-847-4871
I INOIS
Parts Town
Lombard 708-865-7278
Eichenauer Elec. Service
Decatur 217-429-4229
Midwest Elec. Appl. Service
Elmhurst 630-279-8000
Cone’s Repair Service
Moline 309-797-5323
INDIANA
GCS Service
Indianapolis 317-545-9655
IOWA
Electric Motor Service Co.
Davenport 319-323-1823
Goodwin Tucker Group
Des Moines 515-262-9308
KENTUCKY
Service Solutions Group
Lexington 859-254-8854
Service Solutions Group
Louisville 502-451-5411
OUISIANA
Chandlers Parts & Service
Baton Rouge 225-272-6620
MARY AND
Electric Motor Service
Baltimore 410-467-8080
GCS Service
Silver Spring 301-585-7550
MASSACHUSETTS
Ace Service Co., Inc.
Needham 781-449-4220
MICHIGAN
Bildons Appliance Service
Detroit 248-478-3320
Commercial Kitchen Service
Bay City 517-893-4561
Midwest Food Equip. Service
Grandville 616-261-2000
MINNESOTA
GCS Service
Plymouth 800-345-4221
MISSOURI
General Parts
Kansas City 816-421-5400
Commercial Kitchen Services
St. Louis 314-890-0700
Kaemmerlen Parts & Service
St. Louis 314-535-2222
NEBRASKA
Anderson Electric
Omaha 402-341-1414
NEVADA
Burney’s Commercial
Las Vegas 702-736-0006
i. Tech Commercial Service
N. Las Vegas 702-649-4616
NEW JERSEY
Jay ill Repair
Fairfield 973-575-9145
Service Plus
Flanders 973-691-6300
NEW YORK
Acme American Repairs, Inc.
Brooklyn 718-456-6544
Alpro Service Co.
Brooklyn 718-386-2515
Appliance Installation
Buffalo 716-884-7425
Duffy’s Equipment Services, Inc.
Buffalo 800-836-1014
3Wire Northern
Plattsburgh 800-634-5005
Duffy’s Equipment Services, Inc.
Sauquoit 800-836-1014
J.B. Brady, Inc.
Syracuse 315-422-9271
NORTH CARO INA
Authorized Appliance
Charlotte 704-377-4501
OHIO
Akron/Canton Comm. Svc. Inc.
Akron 330-753-6635
Service Solutions Group
Cincinnati 513-772-6600
Commercial Parts and Service
Columbus 614-221-0057
Electrical Appl. Repair Service
Brooklyn eights 216-459-8700
E. A. Wichman Co.
Toledo 419-385-9121
OK AHOMA
agar Rest. Service, Inc.
Oklahoma City 405-235-2184
Krueger, Inc.
Oklahoma City 405-528-8883
OREGON
Ron’s Service, Inc.
Portland 503-624-0890
PENNSY VANIA
Elmer Schultz Services
Philadelphia 215-627-5401
FAST Comm. Appl. Service
Philadelphia 215-288-4800
Appliance Installation & Service
Pittsburgh 412-809-0244
K & D Service Co.
arrisburg 717-236-9039
Electric Repair Co.
Reading 610-376-5444
RHODE IS AND
Marshall Electric Co.
Providence 401-331-1163
SOUTH CARO INA
Whaley Foodservice Repair
W. Columbia 803-791-4420
TENNESSEE
Camp Electric
Memphis 901-527-7543
TEXAS
GCS Service
Fort Worth 800-433-1804
Armstrong Repair Service
ouston 713-666-7100
Cooking Equipment Specialist
Mesquite 888-866-9276
Refrigerated Specialist, Inc.
Mesquite 888-866-9276
Commercial Kitchen Repair Co.
San Antonio 210-735-2811
UTAH
La Monica’s Rest. Equip. Service
Murray 801-263-3221
VIRGINIA
Daubers
Norfolk 757-855-4097
Daubers
Springfield 703-866-3600
WASHINGTON
3Wire Restaurant Appliance
Seattle 800-207-3146
WISCONSIN
A.S.C., Inc.
Madison 608-246-3160
A.S.C., Inc.
Milwaukee 414-543-6460
CANADA
A BERTA
Key Food Equipment Service
Edmonton 780-438-1690
BRITISH CO UMBIA
Key Food Equipment Service
Vancouver 604-433-4484
Key Food Equipment Service
Victoria 250-920-4888
MANITOBA
Air Rite, Inc.
Winnipeg 204-895-2300
NEW BRUNSWICK
EMR Services, Ltd.
Moncton 506-855-4228
ONTARIO
R.G. enderson Ltd.
Toronto 416-422-5580
Choquette - CKS, Inc.
Ottawa 613-739-8458
QUÉBEC
Choquette - CKS, Inc.
Montreal 514-722-2000
Choquette - CKS, Inc.
Québec City 418-681-3944
UNITED KINGDOM
Marren Group
Northants [phone]