Sunny Health & Fitness EVO-FIT SF-T7955 User manual

EVO-FIT TREADMILL
SF-T7955
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions.
Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE
CONTACTED US: [e-mail] or 1-877-90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INFORMATION
We thankyou for choosing ourproduct.To ensure your safety and health, please use this equipment
correctly. It is importantto read this entire manual before assembling and using the equipment. Safe
and effective use can only be achieved if the equipment is assembled, maintained and used properly.
It is your responsibility to ensure that all users of the equipment are informed of all warnings and
precautions.
1. Before startingany exercise program, you should consult your physician todetermine if you have
any medical or physical conditions that could put your health and safety at risk, or prevent you
from using the equipment properly. Your physician’s advice is essential if you are taking
medication that affects your heart rate, blood pressure or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest,
irregular heartbeat, shortness of breath, lightheadedness, dizziness or feelings of nausea. If you
do experience any of these conditions, you should consult your physician before continuing with
your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet.
To ensure safety, the equipment should have at least 4 feet (1.2 M) of free space all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of
the equipment can only be maintained if it is regularly examined for damage and/or wear and
tear.
6. Always use the equipment as indicated. If you find any defective components while assembling
or checking the equipment, or if you hear any unusual noises coming from the equipment during
exercise, discontinue use of the equipment immediately and do not use until the problem has
been rectified.
7. Wearsuitable clothingwhile using the equipment.Avoid wearing loose clothing that may become
entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 275 pounds (125 KG).
10.The equipment is not suitable for therapeutic use.
11.To avoid bodily injury and/or damage to the product or property, proper lifting and moving is
required.
12.Your product is intended for use in cool, dry conditions. You should avoid storage in extreme
cold, hot or damp areas as this may lead to corrosion and other related problems.
13.This equipment is designed for indoor and home use only, it is not intended for commercial use!

2
EXPLODED DIAGRAM

3
PARTS LIST
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
1 Base Frame 1 39 Rear Roller 1
2 Left Upright Tube 1 40 Cylinder 1
3 Right Upright Tube 1 41 Hook 180*25.4*T2.5 2
4 Incline Frame 1 42 Spring Φ34*25*Φ2 4
5 Main Frame 1 43 Upper Motor Cover 714*88*353 1
6 Console Frame 1 44 Lower Motor Cover 714*80*353 1
7 Screw M8*25L 2 45 Left Upright Cover 55*156*184 1
8 Screw M8*35L*S17L 4 46 Right Upright Cover 55*156*184 1
9 Screw M8*30L 1 47 Left Wheel Cover 40*105*183 1
10 Screw M8*40L*S18L 2 48 Right Wheel Cover 40*105*183 1
11 Screw M8*50L*S20L 1 49 Left Side Rail (upper) 106*68*1440 1
12 Screw M8*70L*S20L 8 50 Right Side Rail (upper) 106*68*1440 1
13 Screw M4*12L 2 51 Left Decorative Cover 105*72*300 1
14 Screw ST2.5*8L 7 52
Right Decorative
Cover
105*72*300 1
15 Screw ST2.9*8L 2 53 Cushion 52*52*35 4
16 Screw ST2.9*14L 26 54 Console Panel 380*405*50 1
17 Screw ST2.9*20L 4 55 Console Panel Cover 273*32*21 1
18 Screw ST3.9*14L 69 56 Console Bottom Cover 874*493*123 1
19 Screw ST3.9*45L 2 57 Console Front Cover 380*62*66 1
20 Screw ST3.9*13L 2 58
Handlebar Upper
Cover
380*144*107 1
21 Bolt Φ12*M10*30L*S10L 2 59
Handlebar Lower
Cover
352*83*27 1
22 Screw Φ12*M10*28L 2 60 Left Handlebar Cover 71*99*45 1
23 Screw M4*10L 11 61 Right Handlebar Cover 71*99*45 1
24 Screw M8*12L 2 62 Fan Blade 147*60*20 1
25 Screw M8*16L 8 63 Fan Cover 172*68*64 1
26 Screw M8*55L 1 64 Tablet Clip 45*18*21 1
27 Screw M8*65L 2 65 Upper Tablet Cover 213*156*16 1
28 Screw M10*50L 1 66 Lower Tablet Cover 213*156*15 1
29 Screw M10*60L*S15L 1 67 Wheel Washer Φ22*Φ12.2*1.1T 4
30 Screw ST3.2*10 2 68 Wheel Washer Φ21*Φ10.2*1.1T 2
31 Nut M8*7T 6 69 Adjustable Cap Φ40*36*M8 PVC 4
32 Nut M10*9T 4 70 Frame wheel Φ8.2*Φ50*T20 2
33 Flat Washer Ф5*Ф16*1.5T 10 71 PU Wheel Φ8.2*Φ56*23T 2
34 Flat Washer Ф8*Ф16*2T 27 72 Console Supporter 47*27*22, ABS 2
35 Flat Washer Ф10*Ф20*2T 4 73 Cushion Block 60*36*30 2
36 Spring Washer Ф8.5*Ф13.5*2.5T 2 74 Handlebar Foam 2
37 Spanner S6 1 75 Handlebar Cap 2
38 Front Roller 176
Running Board
Cushion
Ф25*25*M8 2

4
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
77 Rubber Cushion Ф25*Ф8*7 2 97
Signal Connecting
Wire 1
5P/2000mm 1
78 Running Belt 2940*510*1.6T 1 98
Power Connecting
Wire 1
100+200mm 1
79 Belt PJ522 1 99
Power Connecting
Wire 2
200mm 1
80 Cable Tie 3*100, BK 7 100
Power Connecting
Wire 3
100mm 1
81 Cable Tie 4*200, BK 2 101
Power Connecting
Wire 4
200mm 2
82 Cable Tie 0TP1508 160mm*3.5 3 102 Ground Wire 1 100mm 1
83 Cable Tie GTP-130ST(TYPE2) 2 103 Filter 1
84 Tie 5*150 2 104 Ground Wire 2 1
85 Cushion 25*20*24.5*T2.0 BK 1 105 Safety Key Wire 3P/350mm 1
86 Sensor Supporter PP 1 106 Fan 1
87 Hand Pulse 2 107 Speaker 2
88 Switch Supporter 49*13*16 1 108 Console 1
89 Safety Key 1 109
Signal Connecting
Wire 2
5P/800mm 1
90 Controller B506DV13--110V 1 110 Ground Wire 3 800mm 1
91 Motor
1.5HP/105V/5200RP
M
1 111
Upper Hand Pulse
Wire
2P/400mm 2
92 Incline Motor JS64-3A-17N-110V 1 112
Lower Hand Pulse
Wire
2P/300mm 2
93 Socket DB-14-5F(2.0) 1 113 Power Cord 1830mm 1
94 Switch
M1L15-A11B1
15A/125V
1 114 USB Charging Board 1
95 Magnetic Ring Φ31*Φ19*13 1 115 Running Board 1300*684*18T 1
96 Speed Sensor Wire 2P/1200MM 1

5
HARDWARE PACKAGE
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
The model number (found on cover of manual)
The product name (found on cover of manual)
The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front
of the manual)
Please contact us at [e-mail] or 1- 877 - 90SUNNY (877-907-8669).
#12 M8*70L*S20L 8PCS
#13 M4*12L 2PCS
#34
φ 8* φ 16*2T 12PCS
#37 S6 1PC
#25 M8*16L 4PCS

6
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-
907-8669).
STEP 1:
We recommend having two
people to do the assembly.
Open the carton and remove
contents.
Place the Main Frame (No. 5)
on level ground, and ensure that
you have a work area that is
clean and has adequate space.
Do not cut the Packing Belt
(No. B) until the assembly is
complete!
STEP 2:
There are 2 joints for Signal
Connecting Wire 1 (No. 97).
Insert the
Signal Connecting
Wire 1 (No. 97)
through the
Right Upright Tubes (No. 3).
Attach
Left & Right Upright
Tubes (No. 2 & 3) to the Main
Frame (No. 5) with 4 Screws
(No. 12) and 4 Flat Washers
(No. 34). Tighten an
d secure
with Spanner (No. 37).
Note: Do not pinch or cut any
wires when attaching the Right
Upright Tube (No. 3)
to the
Main Frame (No. 5).
#12 M8*70L*S20L 8PCS
#34 φ8*φ16*2T 8PCS
#37 S6 1PC

7
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-
907-8669).
STEP 3:
Connect the one joint for Signal
Connecting Wire 1 (No. 97) with
the Signal Connecting Wire 2
(No. 109). Connect another joint
for
Signal Connecting Wire 1
(No. 97) with Ground Wire 3
(No. 110).
Attach Console Bottom Cover
(No. 56) to Left & Right Upright
Tubes (No. 2 & 3) with 4 Flat
Washers (No. 34) and 4 Screws
(No. 25). Tighten and secure with
Spanner (No. 37).
Note:
Do not pinch or cut any
wires when attaching the
Console (No. 56) to the Left &
Right Upright Tubes (No. 2 & 3).
STEP 4:
Cover the
Left & Right
Handlebar Covers (No. 60 & 61)
to the handlebars for
Left &
Right Upright Tubes (No. 2 & 3).
Cover the Lef
t and Right
Upright Covers (No. 45 & 46) to
the Left & Right Upright Tubes
(No. 2 & 3) with 2 Screws (No.
13). Tighten and secure with
Spanner (No. 37).
#25 M8*16L 4PCS
#34
φ
8*
φ 16*2T 8PCS
#37 S6 1PC
#13 M4*12L 2PCS
#37 S6 1PC

8
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-
907-8669).
STEP 5:
Insert the Upper Tablet Cover
(No. 65) to the
Console (No.
56).
Insert the Safety Key (No. 89) to
Handlebar Upper Cover (No.
58).
Cut the Packing Belt (No. B).
Assembly is now complete!

9
LUBRICATING THE TREADMILL
*IMPORTANT NOTE:
You will need to lubricate your treadmill before the first use.
Lubricating the Running Board (No.115) and Running Belt (No. 78) is essential as the friction
between the two affects the life span and function of the treadmill. Inspect the Running Board (No.
78) and Running Belt (No. 115)regularly. Should you find any wear on the Running Board (No.
115), please contact us at: [e-mail].
WARNING: Always unplug the treadmill from the electrical outlet before cleaning, lubricating
or repairing the unit.
HOW TO LUBRICATE:
1. Raise the Running Belt (No. 78) up onone side and apply lubricant to the Running Board (No.
115). Use a rag to thoroughly wipe the lubricant over the Running Board (No. 115). Repeat
this process for the other side.
2. The moving parts should turn freely and quietly. Abnormality of moving parts will affectthe safety
of the equipment. Inspect and tighten bolts regularly.
3. To better maintain the treadmill and prolong its lifespan, it is suggested that maintenance be
done on a regular basis.
4. A loose Running Belt (No. 78) will result in the runner sliding off during use, while too tight of
a Running Belt (No. 78) will negatively affect the motor’s performance and also create more
friction between the roller and Running Belt (No. 78). The most suitable tightness for the
Running Belt (No. 78) is pulled out 50-75mm from the Running Board (No. 78).
The following time table is recommended:
Light user (less than 3 hours/ week) every five months
Medium user (4-7 hours/ week) every two months
Heavy user (more than 7 hours/ week) every month

10
MAINTENANCE & CARE
General cleaning will help prolong the life and performance of your treadmill. Keep the unit clean
and maintained by dusting the components on a regular basis. Clean both sides of the Running
Belt (No. 78) to prevent dust from accumulating underneath the Running Belt (No. 78). Keep your
running shoes clean so that dirt from your shoes does not wear out the Running Board (No. 115)
and Running Belt (No. 78). Clean the surface of the Running Belt (No. 78) with a clean damp
cloth.
To better maintain the treadmill and prolong its life it is suggested that the machine be powered off
for 10 minutes every 2 hours and fully powered off whenever not in use.
A loose Running Belt (No. 78) will result in the runner sliding off when running, while too tight of a
Running Belt (No. 78) will negatively affect the motor’s performance and also create more friction
between the roller and Running Belt (No. 78). The most suitable tightness for the Running Belt
(No. 78) is pulled out 50-75mm from the Running Board (No. 115).
CENTERING THE RUNNING BELT:
Place the treadmill on level ground and set it at 3-5mph to check if the Running Belt (No. 78) drifts.
1. If the Running Belt (No. 78) moves
to the right, turn the adjusting bolt on
the right side ¼turn clockwise, then
turn
the left adjustment bolt ¼ turn
counter-clockwise. If the Running Belt
(No. 78) doesnotmove, keep adjusting
¼ turn at a time until it centers.Refer to
Fig. A.
2. If the Running Belt (No. 78) moves
to the left, turn the adjusting bolts on
the left side ¼of a turn clockwise, then
turn the right adjustment bolt ¼ turn
counter-clockwise. If the Running Belt
(No. 78) doesnotmove, keep adjusting
¼ turn at a time until it centers. Refer
to Fig. B.
3. Over time the Running Belt (No.78)
will loosen. To tighten the belt, turn the
Left & Right side adjustment bolts one
full turn clockwise, check the tension of
the Running Belt (No. 78). Continue
this process until the
Running Belt
(No. 78) is at the correct tension. Make
sure to adjust both sides
equally to
ensure correct Running Belt (No. 78)
alignment. Refer to Fig. C.
Fig. A
Fig. B
Fig. C

11
FOLDING INSTRUCTIONS
FOLDING
UNFOLDING:
Turn off the power before folding.
Restore the incline to flat position
(Incline Level 0). Place your hand at
position “A” and lift up on the Main
Frame (No. 5)
to push top of the
running board forward until the
Cylinder (No. 40) locks into the tube.
Note: When the Cylinder (No. 40)
successfully locks into the tube you will
hear a clicking sound.
Before lowering the Main Frame (No.
5)
, ensure that the space directly
underneath is clear of any objects and
the power is turned off.
Grasp the Main Frame (No. 5) at
position “A” with one hand. Next, using
your foot, firmly push against the
Cylinder (No. 40) “B” and press down
on the Main Frame (No. 5). Once the
Main Frame (No. 5) starts to lower, it
will automatically continue to steadily
lower itself until it reaches level ground.

12
HOW TO MOVE THE MACHINE
Before attempting to move the
treadmill, make sure that it has been
properly folded. Unplug the power
cord.
To tilt, start by placing one hand at
position “P” to support the top end of
the treadmill. Next, place one foot at
position “M” to hold the bottom end
of the treadmill steady. With yourfoot
at “M
”, slowly tilt the top of the
treadmill downward towards the
ground. Once the treadmill reaches
a low enough point,thewheels ofthe
treadmill touch the ground.
To transport, hold the
treadmill at
position “P” and tilt until the wheels
“M” are able to move on the ground.

13
IMPORTANT ELECTRICAL INFORMATION
WARNING: This treadmill requires a power source of 10.5 amps (100-120V) in order to
properlyoperate. For your safety, as well as the safety of others, please verify that the power source
is correct before plugging the equipment. Any power source above or below this level could cause
significant damage to the equipment and or user.
GROUNDING METHODS:
This product must be grounded. Grounding provides the least resistance for electrical current and
will reduce the risk of electric shock. The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances. Ensure that the
product is connected to an outlet which contains the same configuration as the plug. Do not use an
adaptor for this product.
This product is for use on a nominal 100-120V circuit and has a grounding plug that looks like the
plug illustrated in sketch A. Make sure that the product is connected to an outlet having the same
configuration as the plug. No adapter should be used with this product.
DANGER:
Improper connection of the equipment-grounding conductor can result in risk of electric shock.
Check with a certified electrician if you are in doubt as to whether the product is properly grounded.
Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet
installed by an electrician.
WARNING!
1. NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power
cord awayfrom any moving part ofthe treadmill includingthe elevation mechanism and transport
wheels.
2. NEVER operate the treadmill using a generator or UPS power supply.
3. NEVER remove any cover without first disconnecting AC power.
4. NEVER expose the treadmill to rain or moisture. This treadmill is not designed for use outdoors,
near pools or in any other high humidity environment.
(A)

14
EXERCISE INSTRUCTIONS
GETTING STARTED:
Before starting any exercise program, you should consult with your physician to determine if you
have any medical or physical conditions that could put your health and safety at risk or prevent you
from using the equipment properly.
Be aware of your body’s signals. Incorrect or excessive exercise can damage your health.
Stop exercising immediately if you experienceany of the following symptoms: pain, tightness in your
chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea.
Get to know your treadmill. Before attempting to use the treadmill take sometime to stand alongside
and familiarize yourself with the controls.
1. Turn on the power switch.
2. Once you get on, you can stand with your feet on the side rails and stabilize yourself by
holding onto the handrails.
3. Next, attach the clip end of the Safety Key (No. 89) to your clothes and insert the magnetic
end of the key into the computer console.
4. Press the START key to start the treadmill.
5. The treadmill will start at the system default setting speed of 1.0 MPH. When you feel
comfortable, you may slowly increase this speed.
6. When you are finished with your exercise, press the STOP key to stop the treadmill or you
can remove the magnetic end of the Safety Key (No. 89) to stop the treadmill.

15
THE DISPLAY CONSOLE
DISPLAY FUNCTION
1. Speed display window showing current speed value.
2. Incline/ Heart rate display window shows the incline value and heart rate.
3. Time display window shows the time count-down and count-up when in running state.
4. Distance display window shows distance count-down and count-up when in running state.
5. Calories display window shows calories count-down and count-up when in running state.

16
KEY FUNCTION
1. START：
Press to start up the treadmill in the stop state. The default speed displayed is 1.0 MPH.
2. PAUSE / STOP:
When the treadmill is running, press PAUSE / STOP once to pause the treadmill. When the
treadmill is paused, press PAUSE / STOP to stop the treadmill, and all values will be cleared.
3. INCLINE + / INCLINE - :
When the treadmill is running, press to increase or decrease the incline. Value increases or
decreases in increments of 1%. When setting program parameters, press to increase or
decrease the set value. If you press and hold for 0.5 seconds, values will increase or decrease
quickly.
4. SPEED+ / SPEED -:
In setting state, press to increase or decrease the set value. When the treadmill isrunning, press
to increase or decrease the speed. Value increases or decreases in increments of 0.1 MI. After
holding for more than 0.5 seconds, automatic continuous acceleration and deceleration will
occur.
5. MANUAL:
In other optional mode state, press this button to return to home screen.
6. GOALS:
In standby mode to switch off 3 count-down mode: time count-down, distance count-down,
calories count-down.
7. WEIGHT LOSS:
Press to choose WEIGHT LOSS mode.
8. INTERVAL:
Press to choose INTERVAL mode.
9. HEARTRATE:
Press to choose HEART RATE control mode.
10. CUSTOM:
Press to choose CUSTOM mode.
11. UP / DOWN:
In HEART RATE control mode or CUSTOM mode, press to adjust parameter.
12. USER:
Press to choose User 1 or User 2.
13. OK:
In HEART RATE control mode or CUSTOM mode, press to set parameter.
14. SPEED SHORTCUT KEYS:
Press to select 2/4/6/8/10/11 MPH when the treadmill is running.
15. INCLINE SHORTCUT KEYS:
Press to select 3/6/9/12/15/18 when the treadmill is running.
16. FAN KEY:
Press to turn the fan on and off.

17
DATA DISPLAY RANGE AND SETTING RANGE OF VARIOUS PARAMETERS:
DISPLAY
RANGE
DEFAULT
VALUE
MODE
VALUE
SETTING
RANGE
SPEED (MPH)
1.0 – 11.5
┈
1.0
1.0 - 11.2
TIME (MIN)
0:00 - 99.59
30
：
00
30
：
00
5:00 - 99:00
DISTANCE (M)
0 - 99.9
┈
1.0
1.0 - 99.9
CALORIES
（
CAL）
0 - 999
┈
50
10 - 990
INCLINE
（
INCL
）
0 - 18
┈
0
0 - 18
MANUAL MODE:
1. Press START, and the treadmill will start operating. The speed window will display “3,2,1,0” at
the same time. The initial speed is 1.0 MPH.
2. Press SPEED + / SPEED – or speed shortcuts to adjust speed.
3. Press INCLINE +/ INCLINE – or incline shortcuts to adjust the incline.
4. When the treadmill is running, press STOP / PAUSE to stop/pause the treadmill.
5. To stop the treadmill immediately, remove the safety key.
SET UP COUNTDOWN MODE
1. Turn on the treadmill. The treadmill will be in standby mode. Press GOALS key to select time
count-down mode (H1), distance count-down mode (H2), or calories count-down mode (H3).
Press START to start the treadmill.
2. To set countdown mode:
a. In manual mode, press GOALS key to enter time countdown mode. The initial time is 30:00.
Set countdown time by pressing SPEED + / SPEED - or INCLINE + / INCLINE -. Time setting
range: 5:00 - 99:00. Value is in increment of 1 MIN. Press START to start the treadmill. If you
do not press START key and you press GOALS key again, the time value you set will be
cleared and treadmill will go into distance countdown mode.
b. Press GOALS key to enter distance countdown mode. The initial distance is 1.0 MI. Set the
distance by pressing SPEED + / SPEED – or INCLINE + / INCLINE –. Distance setting range:
1.0 - 99.9 MI. Value is in increment of 1 MI. Press START to start the treadmill. If you do not
press START key and you press GOALS key again, the distance value you set will be cleared
and treadmill will go into calorie countdown mode.
c. Press GOALS key to enter calorie countdown. The initial calorie will be displayed as 50.0 kcal.
Set the calorie by pressing SPEED + / SPEED – or INCLINE + / INCLINE –. Calorie setting
range: 10 - 990 kcal. Value increases in increment of 10 kcal. Press START to start the
treadmill. If you do not press START and you press GOALS key again, the calorie value you
set will be cleared and treadmill will go into standby mode.
WEIGHT LOSS MODE
1. In standby, press WEIGHT LOSS key to select pre-set program P1-P6.
2. Press SPEED + / SPEED – or INCLINE + / INCLINE – to adjust the time. The initial time is set
to be 30:00. Only time can be set. Setting range: 5:00 - 99:00.
3. Press START key. The treadmill will start running and the speed will gradually increase to the
value for the first section of program (see details in the table of program parameters);
4. Press SPEED + / SPEED – or speed shortcuts key to adjust speed.
5. Press INCLINE + / INCLINE – or incline shortcuts key to adjust the incline.
6. Each program is divided into 10 sections. Operating time for each section will be 1/10 of the set
time.
7. When the set time goes to zero, the treadmill will slow to a stop. All values go to zero and
treadmill is now in standby state.
8. At any time, if you need to stop the treadmill immediately, remove the safety key.

18
PROGRAM PARAMETERS
(speed is in MPH)
Setup time / 10 = running time for each section
1
2
3
4
5
6
7
8
9
10
P1
SPEED
2
4
3
4
3
5
4
2
5
3
INCLINE
1
1
2
2
2
3
3
2
2
2
P2
SPEED
2
5
4
6
4
6
4
2
4
2
INCLINE
1
2
2
2
2
4
4
3
2
2
P3
SPEED
2
5
4
5
4
5
4
2
3
2
INCLINE
2
3
3
2
2
6
6
3
2
2
P4
SPEED
2
3
4
6
7
6
5
4
4
6
INCLINE
2
3
3
2
2
6
6
3
2
2
P5
SPEED
3
6
7
5
8
5
9
6
5
3
INCLINE
3
3
3
4
4
3
3
2
2
2
P6
SPEED
3
6
7
5
8
6
7
6
4
3
INCLINE
3
5
5
5
4
3
3
4
3
2
INTERRVAL MODE
1. In standby state, press WEIGHT LOSS key to select pre-set program P7-P12.
2. Press SPEED + / SPEED – or INCLINE + / INCLINE – to adjust the time. The initial time is set
to be 30:00. Only time can be set. Setting range: 5:00 - 99:00.
3. Press START key. The treadmill will start running and the speed will gradually increase to the
value for the first section of program (see details in the table of program parameters);
4. Press SPEED + / SPEED – or speed shortcuts key to adjust speed.
5. Press INCLINE + / INCLINE – or incline shortcuts key to adjust the incline.
6. Each program is divided into 10 sections; operating time for each section will be 1/10 of the set
time.
7. When the set time goes to zero, the treadmill will slow to a stop. All values go to zero and
treadmill is now in standby state.
8. At any time, if you need to stop the treadmill immediately, remove the safety key.
PROGRAM PARAMETERS
(speed is in MPH)
Setup time / 10 = running time for each section
1
2
3
4
5
6
7
8
9
10
P7
SPEED
2
5
2
5
2
5
2
5
4
3
INCLINE
1
3
1
2
1
3
1
2
1
1
P8
SPEED
2
6
2
6
2
6
2
6
4
3
INCLINE
1
4
2
4
2
4
3
4
2
4
P9
SPEED
2
7
2
7
2
7
2
7
4
3
INCLINE
1
5
2
5
2
5
3
5
2
5
P10
SPEED
2
8
2
8
2
8
2
8
4
3
INCLINE
1
6
2
6
2
6
3
6
2
6
P11
SPEED
3
9
3
9
3
9
3
9
4
3
INCLINE
1
7
2
7
2
7
3
7
2
7
P12
SPEED
4
9
4
9
4
9
4
9
4
3
INCLINE
1
8
2
8
2
8
3
8
2
8

19
HEART RATE MODE
1. In standby, press HEART RATE key to set.
2. Press UP/DOWN keys to set time value. Press OK key to confirm.
3. Press UP/DOWN keys to set target heart rate value. Press OK key to confirm.
4. Press START key to exercise.
Note: During exercise, if the current heart rate is lower than the target heart rate, the speed will
gradually increase. When the speed reaches the max speed (6.0 MPH) for HEART RATE MODE,
the incline will gradually increase. When the current heart rate is higher than the target heart rate,
incline will decrease if applicable. If no incline, speed will slow down to min speed (1.0 MPH) for
HEART RATE MODE.
CUSTOM MODE
1. In standby state, press CUSTOM key to set.
2. Press UP/DOWN keys to choose USER 1 or USER 2. Press OK key to confirm.
3. Press UP/DOWN keys to set time value. Press OK key to confirm.
4. Press SPEED + / SPEED – to set speed for each section. Press INCLINE + / INCLINE – to set
incline for each section.
5. Press START key to exercise.
SLEEP MODE
If there is no operation for 10 minutes in standby mode, the console will enter Sleep Mode. Press
any button to wake up the console, then the console will enter standby mode.
SAFETY KEY FUNCTION
Safety key is for emergency stop. Remove the safety key in any mode, and the treadmill will slow
down rapidly until it stops. The console will DISPLAY E0 in speed window.
ERROR MESSAGE
V1.1
E0
Safety key came off
E1
Speed abnormal
E2
Over current
E4
Motor disconnect
E5
Communication error
E6
Power tube or relay open
E7
Calibration error