Hausted APC Series User manual

THE A.P.C. SERIES
MODEL ASC275 & ASC375
İİ" HAUSTED'
OPERATING
AND
SERVICE
MANUAL
927 LAKE ROAD P.0. BOX 710 MEDINA, OHIO 44258
[phone] 1-800—428—7833
P/N 069071-65 (9604)

JT
HAUSTED
450
TABLE
OF
CONTENTS
PAGE 1
PAGE 2
PAGE 3 -
PAGE 4 -
PAGE 5 -
PAGE 6 -
PAGE 7
PAGE 8
PAGE 9
PAGE 10 -
PAGE fl -
PAGE 12 -
PAGE 13 -
PAGE 14 -
UNPACKING INSTRUCTIONS
GENERAL INSTRUCTIONS
CHAIR SPECIFICATIONS
BRAKE AND STEER OPERATION
TOP ADJUSTMENT
TOP ADJUSTMENT — CONTINUED
USING THE SURGICAL LEGS
INDEPENDENT LEG SECTION OPERATION
ADJUSTABLE FOOTREST OPERATION
HINGING RAIL OPERATION
OPERATING THE A.S.C. HEADREST
BASE ASSEMBLY
SEAT SECTION ASSEMBLY
FOOT SECTION ASSEMBLY
BACK SECTION ASSEMBLY — MODEL 275
BACK SECTION ASSEMBLY — MODEL 375
HEAD SECTION ASSEMBLY — MODEL 275
HEAD SECTION ASSEMBLY — MODEL 375
WRIST WREST ASSEMBLIES
PREVENTIVE MAINTENANCE GUIDE
OPTIONAL ACCESSORIES

IT HAUSTED
IMPORTANT
REPORT ANY SHIPPING DAMAGE IMMEDIATELY 1
INFORM SHIPPER OF ANY DAMAGES — LEAVE
CARTON INTACT. LEAVE THE CHAIR IN THE
RECEIVING AREA UNTIL INSPECTION IS COMPLETE.
UNPACKING INSTRUCTIONS
Your A.P.C. series chair has been carefully packaged at our
manufacturing plant to insure safe shipment to your medical
facility. There are several procedures you must follow to
put your new chair into service. These procedures only
take a few minutes to complete and are required to insure
proper operation of the chair.
STEP 1 - CUT THE TWO METAL BANDS AROUND THE SHIPPING CARTON.
STEP 2 - REMOVE THE TOP HALF OF THE CARTON AND CUT ONE SIDE OF THE
BOTTOM HALF.
STEP 3 - REMOVE THE CHAIR FROM THE CARTON.
STEP 4 - CHECK TO SEE iF ALL FEATURES OF THE CHAIR WORK PROPERLY.
IF ALL FEATURES WORK GO TO STEP 5. IF ANY OF THE FEATURES OF
THE CHAIR DO NOT WORK PROPERLY CALL HAUSTED FOR SERVICE
AT: 1-800-428-7833 OR IN OHIO [phone]
STEP 5 — CLEAN YOUR NEW CHAIR USING A MILD DETERGENT TO REMOVE ANY
DIRT ACCUMULATED DURING SHIPMENT AND PLACE THE CHAIR
INTO SERVICE.
PAGE 1

Jf
HAUSTED
ast.
GENERAL
INSTRUCTIONS
£
CHAIR
SPECIFICATIONS
ADJUSTABLE HEADREST SURGICAL BAR
N BUILT-IN PUSHBAR
CHAIR SPECIFICATIONS
WARNING LABEL
THE ASC. HAS BEEN DESIGNED TO
MEET BOTH THE CLINICAL NEEDS
FOR MINOR HEAD AREA TREATMENT
AND PATENT'S NEED FOR COMFORT. PATENT COMFORT
CUSHIONS
PATIENT SURFAGE SIZE ANONG RAL
CHAR POSTION | STRETCHER POSTION
21" 2” WETH
39.5” 75" LENGTH
UNIT HEIGHT i
CHAR POSTION | STRETCHER POSTION BACKREST
57 22.57 MM
64.5”
30"
MAX.
TRANSFER
TOBE
DONE ONLY FROM
THE “CENTER SIDE”
A FEW FEATURES OF THE ASC, ARE RAL DOWN, E
*SURGEON OPERATED HEADREST
*HYDRAUUC HEIGHT ADJUSTMENT
*TEN DEGREE TRENDELENBURG
*4 WHEEL LOCK CASTER BRAKING
“STEERING LOCK CASTER RESTRAINT
*PNEUMATIC BACKREST < N STRAP ROD
“INDEPENDENT LEG SECTION
*ADJUSTABLE
FOOT
REST
、
*BULT IN STORAGE TRAY
PLUS:
THE ASC. COMES STANDARD WITH
~ REMOVABLE PRE-OP / POST—OP
HEAD EXTENSION W/ PAD.
— BUILT IN TELESCOPING SURGICAL
SUPPORT LEGS. RAIL LATCH
~ THICK COMFORT CUSHIONS, FOREST
GREEN IS STANDARD COLOR. HEIGHT ADJUSTMENT
* VARIETY OF DIFFERENT COLORED PEDAL
COMFORT CUSHIONS ARE AVAILABLE
BY
SPECIAL
ORDER.
BRAKE/STEERING
LOCK
PEDAL
ADJUSTABLE FOOT REST INDEPENDENT FOOT SECTION LEVER
GENERAL INSTRUCTIONS
~AS A VALUED CUSTOMER AND USER OF HAUSTED'S UNIQUE A.S.C. CHAR, THESE GENERAL INSTRUCTIONS ARE TO INSURE PROPER USE IS UNDERSTOOD AND FOLLOWED
TO OBTAIN MAXIMUM SAFETY AND FUNCTION OF YGUR HAUSTED AS.C. CHAR.
—THE A.S.C. CHAIR'S UNEQUALED VERSATILITY FROM CHAIR POSITIONING TO FULL RECLINING 1S DESIGNED TO PERMIT CONVENIENT PATIENT POSITIONING
AND TREATMENT WHEN REQUIRED WITH A MAXIMUM PATENT WEIGHT OF 325 bs. THE A.S.C. ISNOT INTENDED TO REPLACE A STRETCHER OR GURNEY
OF WHICH HAUSTED OFFERS A COMPLETE PRODUCT LINE FOR YOUR SPECIALTY NEEDS.
-ТНЕ A.S.C. HAS A "WARNING" LABEL AT THE HEAD ANO FOOT END OF THE CHAIR FRAME, STATING: DO NOT SIT ON END — AS TPPING MAY OCCUR.
-PATENT ENTRY, EGRESS AND TRANSFER FROM THE A.S.C. CHAIR SHOULD ALWAYS BE FROM THE CENTER SIDE RAL LOCATIONS, BY LOWERING OF THE
SIDE RAILS AS SHOWN ABOVE. АТ № ПМЕ SHOULD THE PATIENT BE PERMITTED TO ENTER OR EXIT FROM THE ENDS OF THE A.S.C. CHAIR WHEN THE
CHAIR 1S IN PARTIAL OR FULL RECLINE POSITION.
NOTE: WHEN NOT IN USE, BONOT LEAVE THE AS.C. CHAIR IN A FULL OR PARTIAL RECLINE POSITION.
-NOTE: THE PATIENT SHOULD BE SECURED WITH RESTRAINT STRAPS WHEN LEFT UNATTENDED IN A FULL RECLINE POSITION.
~THESE GENERAL OPERATING INSTRUCTIONS ARE TO INSURE PATIENT SAFETY AND PERMITS YOU TO USE YOUR AS.C. CHAIR TO TREAT, TRANSPORT AND
TRANSFER YOUR PATIENT WITH UNEQUALED VERSATRITY AND SAFETY.
IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT THE "HAUSTED CUSTOMER SERVICE DEPARTMENT” AT:
1-800-428-7833 OR (IN OHIO) 216-723-3271
PAGE 2

"HAUSTED
ASC
FIG. 1
AG. 2
FG. 3
FIG. 4
FIG. 5
-
OPERATING
INSTRUCTIONS
BRAKING AND STEERING
APPLYING THE BRAKES
THE
FOUR
WHEEL
CENTRAL
BRAKING
SYSTEM
IS
ACTIVATED
BY
DEPRESSING
THE
RED
PEDAL
AT
EITHER
THE
LEFT
OR
RIGHT
SIDE
AT
THE
FOOT
END
OF
THE
UNIT
(FIG.
1).
TO
FULLY
ENGAGE
THE
BRAKES,
THE
PEDAL
SHOULD
BE
PRESSED
TO
APPROXIMATELY
45.
ALL
FOUR
CASTER
SHOULD
BE
LOCKED
FROM
SWIVELING
AND
ROTATING.
RELEASING THE BRAKES
DEPRESS
THE
BLACK
PEDAL
AT
EITHER
OF
THE
HEAD
END
CORNERS
OF
THE
UNIT,
UNTIL
THE
PEDAL
IS
IN
A
HORIZONTAL
POSITION
(FIG.
2),
ALL
FOUR
WHEELS
SHOULD
ROTATE
AND
SWIVEL
FREELY.
“BRAKES
SHOULD
ALWAYS
BE
ACTIVATED
WHEN
UNIT
IS
NOT
IN
TRANPORT®
APPLYING THE STEERING LOCK
FROM
THE
HEAD
END
OF
THE
ASC
CHAIR,
DEPRESS
THE
BLACK
PEDAL
DOWNWARD
INTO
LOCKED
POSITION
(FIG.
3).
PUSH
THE
ASC
CHAIR
FOWARD.
ONE
CASTER
AT
THE
FOOT
END
WILL
LOCK
INTO
A
NON-SWVEL
MODE.
THIS
ALLOWS
STRAIGHT
STEERING
BY
THE
ATTENDANT,
WHEN
PUSHING
FROM
THE
HEAD
END.
RELEASING THE STEERING LOCK
DEPRESS
THE
RED
PEDAL
AT
EMHER
OF
THE
FOOT
END
CORNERS
OF
THE
UNIT,
UNTIL
THE
PEDAL
IS
IN
A
HORIZONTAL
POSITION
(FIG.
2).
ALL
FOUR
WHEELS
SHOULD
ROTATE
AND
SWIVEL
FREELY.
TOP ADJUSTMENT
RAISING THE TOP
PRESS
THE
PUMP
PEDAL
(PEDAL
NEAREST
THE
HEAD
END)
TO
THE
FLOOR
(FIG.
4),
THEN
RELEASE
THE
PRESSURE
ON
THE
PEDAL.
REPEAT
THIS
PROCESS
UNTIL
DESIRED
HEIGHT
IS
OBTAINED.
USE
SMOOTH
STROKES
ON
PUMP
PEDAL
TO
ENSURE
PATIENT
COMFORT.
LOWERING THE TOP
PRESS
DOWN
ON
THE
RELEASE
PEDAL
(PEDAL
NEAREST
THE
FOOT
END)
(FIG.
5)
UNTIL
DESIRED
HEIGHT
IS
OBTAINED.
RECLINING
THE
CHAIR
INTO
THE
STRETCHER
POSITION
ROTATE
THE
RECLINE
KNOB,
LOCATED
ON
ETHER
SIDE
OF
THE
CHAIR,
TOWARD
THE
BACK
SECTION
(FIG.
6).
PUSH
BACK
ON
THE
BACK
UNTIL
[T
IS
AT
DESIRED
POSITION,
(FIC.
7)
AND
RELEASE
THE
KNOB.
TO
POSITION
THE
BACK
INTO
THE
UPRIGHT
POSITION,
ROTATE
THE
RECLINE
KNOB
AND
LIFT
UP
ON
THE
BACK
SECTION.
“THE
ASC.
SHOULD
BE
KEPT
IN
FULL
UPRIGHT
POSITION
WHEN
NOT
IN
USE"
FIG. 6
FG 7
PAGE 3

HAUSTED ASC
AiG. 8
FIG. 9
FIG. 10
АВ. И
FG. 12
- OPERATING INSTRUCTIONS
TOP ADJUSTMENT - CONTINUED
RECLINING THE CHAIR INTO TRENDELENBURG POSITION
ROTATE THE RECLINE KNOB, LOCATED ON EITHER SIDE OF THE
CHAIR, AWAY FROM THE BACK SECTION (FIG. 8). PUSH BACK ON THE
BACK SECTION UNTIL IT 1S IN THE TRENDELENBRG POSITION (FIG. 9).
AND RELEASE THE KNOB. TO REMOVE FROM THE TRENDELENBURG
POSITION, ROTATE THE KNOB AWAY FROM THE CHAIR WHILE LIFTING
UP ON THE BACK SECTION.
“THE ASC. SHOULD BE KEPT IN FULL UPRIGHT POSITION WHEN NOT IN USE"
USING THE SURGICAL LEGS
ADJUSTING THE TOP
ADJUST THE TOP INCLINE TO DESIRED POSITION AND ADJUST HEIGHT
TO DESIRED POSITION. RELEASE ONE OF THE SURGICAL LEGS FROM THE
BACK OF THE CHAIR (FIG, 10) BY PULLING IT AWAY FROM THE
BACK SECTION. EXTEND THE LEG TOWARD THE LEG SOCKET LOCATED
ON THE BACK OF THE BASE ASSEMBLY (FIG. 11). IF THE LEG EXTENDS
OVER THE SOCKET {DO NOT FORCE THE LEG TO EXTEND BEYOND ITS BULT IN SPRING |
(FIG. 12) THEN THE TOP IS ADJUSTED CORRECTLY, GO TO "ADJUSTING
SURGICAL LEGS’. IF THE LEG DOES NOT REACH THE SOCKET, (FIG. 11)
YOU NEED TO READJUST THE TOP. YOU NEED TO LOWER THE HEIGHT
OR DECREASE THE INCLINE UNTIL THE LEG REACHES THE SOCKET.
ADJUSTING SURGICAL LEGS
RELEASE THE SURGICAL LEGS FROM THE BACK OF THE CHAIR (FIG. 10)
BY PULLING IT AWAY FROM THE BACK SECTION. EXTEND THE LEGS TOWARD
THE LEG SOCKET (FIG. 11), (IF THE LEG DOES NOT REACH, THEN GO
70 "ADJUSTING THE TOP" IN THIS SECTION’) PLACE THE BOTTOM OF THE
LEG OVER THE SOCKET (FIG. 12). TIGHTEN THE LOWER KNOB (FIG. 13)
TO FIX THE LEG ONTO THE SOCKET. THEN TIGHTEN THE UPPER KNOB
(FIG. 14) TO FIX KEEP THE LEG FROM TELESCOPING. | ONCE THE LESS ARE
LOCKED INTO PLACE DO NOT TRY TO ADJUST THE TOP}
DISENGAGING SURGICAL LEGS
LOOSEN THE LOWER KNOB FIRST (FIG. 13). SUPPORT THE LOWER LEG
SECTION (FIG. 15) AND LOOSEN THE UPPER KNOB (FIG. 14), ALLOW
THE LEG TO RETRACT AND PRESS BACK INTO THE STORAGE CLIP.
FIG 6
PAGE 4

ZT HAUSTED 45
FIG. 16
Fig. 19
AG. 20
- OPERATING INSTRUCTIONS
INDEPENDENT LEG SECTION
INDEPENDENT OPERATION
HOLD AND SUPPORT LEG SECTION BY THE BOTTOM OF THE FRAME
TUBE (FIG. 16). PULL OUT ON THE END OF THE RED LEVER (FIG. 16).
ROTATE THE LEVER CLOCKWISE WHILE POSITIONING THE LEG SECTION
(FIG. 17). ONCE DESIRED POSITION OF THE LEG SECTION IS REACHED,
RELEASE THE LEVER AND THE LEG SECTION WILL BE RIDGED (FIC. 18).
WHEN THE LEG SECTION IS INDEPENDENT, IT CAN BE REPOSITIONED
AT ANY TIME BY TURNING THE LEVER CLOCKWISE (FIG. 17).
*ALWAYS SUPPORT THE LEG SECTION WHEN TURNING THE RED LEVER*
RETURNING TO CHAIR MODE
SUPPORT THE LEG SECTION, TURN THE LEVER COUNTERCLOCKWISE
WHILE PUSHING IN ON THE LEVER (FIG. 19). THE LEVER WILL SLIDE
INWARD TO AN INACTIVE POSITION. ONCE THE LEVER IS INACTIVE,
ADJUST THE LEG SECTION UNTIL IT IS IN LINE WITH THE BACK SECTION
(FIG. 20). IT WILL CLICK AS IT RE-ENGAGES WITH THE BACK SECTION.
ADJUSTABLE FOOTREST
REPOSITIONING THE FOOTREST
THE FOOTREST HAS THREE POSITIONS, RETRACTED, LOWER AND THE
UPPER POSITIONS, WITH THE PAN IN THE RETRACTED POSITION PULL OUT,
ON THE HANDLES ON ETHER SIDE OF PAN (FIG. 21). THE FOOTREST
WILL DROP INTO THE LOWER POSITION (FIG, 22). TO PLACE THE
FOOTREST INTO THE UPPER POSITION, GRASP THE HANDLES ON BOTH
SIDES OF THE PAN. TILT THE PAN UP WHILE LIFTING (FIG. 23). ONCE
THE PAN 1S UP ALL THE WAY, TILT THE PAN OUT UNTIL IT LOCKS INTO
POSITION (FIG. 24). TO RETURN THE FOOTREST INTO THE RETRACTED
POSITION, TILT THE PAN UP WHILE LETTING IT SLIDE DOWN, IF NEEDED,
(FIG. 23), INTO THE LOWER POSITION (FIG. 21), CONTINUE TILTING
THE FOOTREST UNTIL IT IS IN THE RETRACTED POSITION.
“WARNING: NEVER STAND ON THE FOOTREST*
AG. 23
AG. 21
Аб. 24
PAGE 5

"HAUSTED
ASL
-
OPERATING
INSTRUCTIONS
HINGING RAILS
REPOSITIONING THE RAIL
THE
APC
RAIL
HAS
TWO
POSITIONS,
UP
AND
DOWN,
BOTH
POSITIONS
LOCK
THE
RAIL
INTO
PLACE.
TO
PUT THE
RAIL
DOWN,
WHILE
SUPPORTING
THE
RAIL
(FIG.
25),
SQUEEZE
THE
TWO
RED
TABS
UNDER
THE
SEAT
(FIG.
26).
ALLOW
THE
RAIL
TO
HINGE
ALL
THE
WAY
DOWN
UNTIL
{T
LOCKS
INTO
PLACE
(FIG.
27).
TO
RAISE
THE
RAIL,
SQUEEZE
THE
TWO
RED
TABS
UNDER
THE
SEAT
(FIG.
26).
LIFT
THE
RAIL
ALL
THE
WAY
UP UNTIL IT LOCKS INTO PLACE,
FIG,
25
AS.C.
HEADREST
PRE—OP / POST—-OP HEAD EXTENSION
TO
REMOVE
THE
HEAD
EXTENSION,
LOOSEN
THE
"1"
KNOB
UNDER
THE
HEADREST
(FIG.
28).
WITH
THE
KNOB
LOOSE
PULL
OUT
ON
THE
HEAD
EXTENSION.
TO
REPLACE
THE
EXTENSION,
SLIDE
THE
EXTENSION
OVER
THE
HEAD
PIECE
USING
GUIDES.
PUSH
THE
EXTENSION
AGAINST
THE
HEADREST
AND
TIGHTEN
"T"
KNOB
(FIG.
28).
ADJUSTING THE ASC 275 HEADREST
FIG.
28
REMOVE
HEAD
EXTENSION
SEE
"PRE-OP/POST~OP
HEAD
EXTENSION”
INSTRUCTIONS.
GRASP
LARGE
T-KNOB
ON
BOTTOM
OF
HEADREST
AND
GRASP
SIDE
OF
HEAD
REST
(FIG.
29).
PULL
T-KNOB
TOWARD
THE
BACK
OF
HEADREST.
WITH
THE
T-KNOB
PULLEO
BACK
HEADREST
PIVOT
HEADREST
TO
DESIRED
POSITION
THEN
RELEASE
THE
KNOB.
ADJUSTING THE ASC 375 HEADREST
REMOVE
HEAD
EXTENSION,
SEE
"PRE-OP/POST~OP
HEAD
EXTENSION’
INSTRUCTIONS.
LOOSEN
THE
KNOB
ON
THE
LEFT SIDE
OF
THE
HEAD
REST
AND
POSITION
THE
HEIGHT
OF
THE
HEADREST
(FIG.
30).
ONCE
THE
DESIRED
POSITION
IS
REACHED,
TIGHTEN
THE
KNOB
AND
TEST
THE
HEADREST
TO
ENSURE
RATCHET
TEETH
ARE
LOCKED.
LOOSEN
THE
KNOB
ON
THE
RIGHT
SIDE
OF
THE
HEADREST
AND
POSITION
THE
ANGLE
OF
THE
HEADREST
(FIG.
31).
ONCE
THE
DESIRED
ANGLE
IS
REACHED,
TIGHTEN
THE
KNOB
AND
TEST
THE
HEADREST
TO
ENSURE
RATCHET
TEETH
ARE
LOCKED,
LOOSEN
THE
TWO
KNOBS
ON
THE
BOTTOM
OF
THE
HEADREST
AND
ADJUST
HEADREST
LENGTH
(FIG
32),
TIGHTEN
KNOBS.
"BEFORE PLACING
PATENTS
HEAD
ON
HEADREST,
APPLY
PRESSURE
TO
THE"
“HEADREST
TO
ENSURE
LOCKING
OF
THE
RATCHET
TEETH*
AG.
29
RG
32
FIG.
30
RG.
33
PAGE 6

37 HAUSTED' AS
MODEL 275 AND 375 BASE ASSEMBLY
54—031080—5/16 FLAT MASHER 一 +
53—066857—INSDE COLUUN ASSEMBLY -1
S2—068189— COLUMN GUDE SCREW W/0 PONT 一 4
51— 05204t~ $ 10-24 x 1/4 PPONTSETSR 一 8
50— 081116 — COMUN GUIDE SCREN 一 +
49—066178— SHORT GUDE SUPPORT —
一 2
46
45031389 3/8 1D. x 1-1/4 OD. FLAT WASHER 2
44 068306— SURGCAL LEG STOP WELDUENT 一 2
43 061155— VECRO HOOK FOR COVER 一 4
42— 061156 VELCRO PILE FOR COVER ni
41 —031092—5/16 INTERNAL TOOTH LOCK WASER 一 2
40 —000794-PQP RVET —2
38— 065129 BELLONS CUP 4
38— 061166 — VELCRO PRE 5" -2
37 — 066167 — VELCRO HODK 4º —2
36— 061287 — BELLOWS MOUNTING ANGLE ASSY —i
35—065399-— BASE COVER
34 — 061192 —HAUSTED PRODUCT LABEL
АР 30611 İR LABEL
32 061188— TRM-LOC 3—1/2"
BELLOWS TOP PLATE 31— 0613;
30— 061261 — APC BELLOWS
78 — 061229 — PUMP PEDAL LABEL ~ LEFT
28—061228—PUUP PEDAL LABEL — RIGHT
27 — 061164 — РА PEDAL PAD
26 — O31055— 1/4-20 LOCK NUT
25 一 062128 1/4~20 x 1=1/4 BUTTON HD SOCKET SOR — 5
24 068045— PUMP PEDAL ~ RIGHT 一 1
23--068045— PUMP PEDAL — LEFT =
22— 061127 — REX BRAKE ROD 一 2
‘21 = 061184— BRAKE PEDAL COVER - BLACK 2
20— 031101 — 1/4-20 x 1/2 SET SCR 一 2
19— 061183 BRAKE PEDAL — LEFT 一 2
061182 BRAKE FEDAL - RIGHT 一 2
31465 3/32 x 1/2 COTIER PN —2
16 — 052419= LAK PIE 一 2
15 06S396— CONNECTING UNK 一 !
14 —062684— CAM LINK — SHORT 一 2
13—062688— EYE BOLT 一 2
12. 061183 BRAKE PEDAL CAP ~ RED me
11 — 031186 — RUESER GROMMET 一 0
10 一 052585 一 M8 x 10 HEX HD CAP SCR 一 8
9 = 062659— CASTER BOLT LOCK PLATE —4
8 —085294— TWH WHEEL STEERING LOCK 一 !
7 — 065293 TWIN WHEEL TOTAL LOCK CASTER -3
6 —031058—5/16-18 FREE THREAD HEX NUT -2
031057 5/16-18 LOCK NUT 一 12
)31076— 1/4 SAE FLAT WASHER 一 12
31334 5/16-18 x 2 HEX HD CAP SCR 一 5
061117 — QUTSDE COLUMN ASSEMBLY 一 4
A —065398— APC BASE FRAME ASS'Y =;
εμίρη No[DeSCRPTON am
PAGE 7

+ HAUSTED' 45c
MODEL 275 AND 375 SEAT ASSEMBLY
25 068073— NYLON ARROW CLIP 一 2
24— 031010— 5/16-18 x 3/4 HEX HO CAP SCR —4
23 031057—5/16-18 LOCK NUT 一 5
22—031080— 5/16 FLAT WASHER -5
21—066830—8 VELCRO PE 一 2
20 061007= 18º VELCRO PILE
19—088059— 710-32 x 1-1/4 PHILUPS PAN HEAD SOR — 4
18—068058— ARM REST PAD -2
17 061148=— SEAT CUSION SUPPORT PLATE 一 1
16 一 12366C 一 BACK AND SEAT CUSHON (MAUVE) 一 1
15 一 051044 SEAT PAN SPACER 一 +
14 031500—f10-24 x 1.0 TRUSS HO MACHINE SCR —4
13—061172—STATORERY TRIGGER PLATE — EFT 一 +
12—0851174—STARONERY TRIGGER PLATE — RIGHT —1
和 1 035188— VINYL TAB RED mi
10— 061101— PLUNGER 一 2
9 一 052763 RAIL PLUNSER SPRING -2
8 —061067==RAL TRIGGER PLATE ASSY =2
7 — 068051— APC 250 SDE RAIL — LEFT ~
6 — 068050 APC 250 SIDE RAL ~ RIGHT 一 !
5 — 061125— REMOVABLE RETAINING WASHER —i
4 —061092-—RAIL PIVOT ROD 一 2
3 —035115 3/4 0D x „395 10 NYLON WASHER: -6
2 031364— 1/4 SAE FLAT WASKER -+
1—068039— APC 5° SEAT SECTION WELOMENT 一 1
σώσω om
PAGE 8

TT HAUSTED ASC
MODEL 275 AND 375 FOOT SECTION
60— 061051—20 x 11.0 VELCRO PRE “2
59031057 — 5/1818 LOCK NUT —4
58 —061350—5/16-18 x 1-1/2 HEX HD CAP SCR —2
S7—061325—PLUNGER TUBE ASSEMBLY - RGHT 一 上
56—961324— 3/8 INTERNAL RETAINNG RING 2
55—06132B-—PLUNGER ROD ASSEMBLY 一 2
54—061320—PLUNGER TUBE ASSEMBLY - FT —1
53—031102—1/4—20 x 1/4 SET SCREW - KMURIED 一 2
$2— 061331 — LEG EXTENSION, TURE 3
51—052641—RETANNG RMG 5103-25 -3
Š0=+060105-=EOHLOK ~ MECHANICAL LOCK 一 1
49—031364— 17/4 SAE FLAT WASHER: 一 +
AB 061310 A PC. LEG CONTROL CABLE ー1
47— 061311 — RIGHT PLUNGER CABLE 一 1
46—0613)2 — LEFT PLUNGER CABLE 一 1
45—000849— CAE TE τι
44— OST — 1/8 x 5/8 SPRNG PH —2
43-= 061339 "e" SURPORT SHAFT 一 1
42—031137—RETANNG RNG 5103-37 -2
41 061364 RETANING RING _ 5103-31 =
40081342 CALE PULL ASSEMBLY “i
30=061346== CONTOL PIVOT SUB= ASSEMBLY =1
36— 061348— PULL. 70 ASSEMBLY τα
37—-031074— 3/16 SAE WASHER -2
B — 061337- ROLLER 一 2
3E—061333— CONTROL BOX BRACKET ASSEMBLY 一
34—081336—FLANGE NYLNER 6L2-FF 一 2
35 — 061338- CONTROL SHAFT =i
32— 06541 — ACIVATNO LEVER BEAR -2
ポー065409 一 ACTVATNG LEVER τα
30—0€1306—LEG SECTON COVER 一 1
29— 061351=—LEG EXTENSION TUBE PIN 一 1
28—031456—9/32 x 1/2 COTTER PIN 一 1
27—060018—5/16 x 10 UN PIN 一 1
26… 031421 10-24 LOCK НОТ 5
25—031432— 10-24 x 5/8 FLAT SOCKET HDSR —2
24 — 031500 10-24 x 10 TRUSS HD MACH SR —1
Zh O85412— ACTVATNG LEER SPACER =1
2 一 061138 HEAD AND FOOT WARNING LABEL —2
2D—031458—MYLAR COVER FOR IDENTIFICATION TAG 1
19 一 0314S7 SERIAL IDENTIFICATION TAG 一 1
18 068058— FOOT SECTION VINYL COVER -T
17—061007—20 x 180 VELCRO PLE 一 2
16— 061141 —FO0T REST WARNING LABEL 一 4
15— O66I13—WAT FOR FOOT REST 一 1
14 — 12965E — FOOT REST CUSHION (MAUVE) 一 1
13— 12068 —LEG SECHON DUSHION (MAUVE) 一 1
12 031081— SHM WASHER 一 12
41— 031137 — RETAINING RING 一 2
10 一 %8072 LEG PAD SUPPORT PLATE 一 下
9 — 051196 — 10-24 3/8 TRUSS HO MACHINE SCR — é
8 —061302—FO0T END CONTROL ASSY 一 了
7 — 061458— 1/8 x 3/4 SPRING PN 一 2
5 —088060—F00T REST ASSY =
$ 030287 3/8 PAL NUT -z
4 — ONSIB— 3/8 x 1-7/15 CLEMS PK -2
3 —061358— OPERATING LABEL τα
2 —051055— 5/16-24 x 15/15 PHILLIPS OVAL HD SCR 一 2
1 —068035—FO0T SECMON ASSY =i
VENIPART KOJ DESCRPNON em
PAGE 9

Tr HAUSTED ASC
MODEL 275 AND 375 BACK SECTION
8 ご e 25
58—088630—. TS BMX CORR
m
56 —031059— 70-24 x 3/8 TESS HD HAHA
55=—031085— 1/4-20 LOCK МИ
$k — 055644 — TUBE ENO CAP
5) —~D6828-~ EXTENSOR SPRNG
52 —068295— INNER SUPPORT IEC
下 一 068239 (HAN
50—088297—SPUT ANG
A8— 031821 f10-24 LOCK KUT
46054510 OUTER LEG NELDNENT
р т 1-1/4 ROUND HD SACKNE SCR 그 一 2
6 一 0583iB: CAL LEG ADIUSTUENT KAOS
meyi 1 1-3/4 SUE? BOLT
058295 SURGICAL SUPPORT LEG ASSEMBLY
061151— BACK COVER SPACER
031364—1/4 SAE FLAT WASHER
41031500 (10-24 x 1.00 TRUSS KD MACHINE SOR
40981435 BROOM, CLP
38—000767 7/32 İD x 1.00 00 RAT WASHER
39—000794-=3/16 x 3/8 POP RVET
37«=061042—HANDLE SUPPORT ANGLE
36—068317—RECLNÉ LABEL — LEFT
35068913 ВЕСНЕ RILEASE ROD + LEFT
34—068318—RECLNE LABEL — RIGHT
33 ee DEI Sme ВОЛНЕ КОВ
32—0I42B—3/6-16 UM KUT
3i — 063312 —RETLNE RELEASE ROD — RIGHT
LE CONNECTOR
5 一 031080 一 1/4 USS FLAT WSNER
27—068702— f10-24 x 1/4 NYLON PPED SET SR
dd A e 8 BE PENSE
25—061078-— TRENDELENBURG TRIGGER PLA
4
053
1014 一 10-24 x 3/8 SOCKET HD CAP SCR
О ПЕСО PLATE eine
18051153- ACTUATOR PIN
16 —D61081— TRENDELENALRG STOP BLOCK
15-069900-05 9040 SPACER
サー067267 GAS PRI 1
3ーQ304 一 5/15-18 * Nin PAT SOOXET HO CHP SR- 4 | —4
12068300— SURGCAL BAR —2|-2
NAS DÉS EP =i|=1
30 — 06119j==APC BACK/SEAT VRYL COVER |!
8 —088629— 05 275/373 BAK SUPPORT PAK —1
8 — 06190720 x 18.0 VELERO PLE 一 2
en! x 1.000 SHOULDER BOLT
2 öğe se -24 x 15/15 PHLLPS pa HD SER
1 一 0 AUS 275 BACK SECTION 10460 -=
I TEUJPART KODESCRPNON BIS
PAGE 10

Ji HAUSTED' AS
MODEL 275 HEAD SECTION
45 — 061198 — 一 BREAD AND FO6T WARNING LASEL (N.5) 一 1
45—068637— HEAD EXTENSİON PAD =
44—062437— 20 x 7.0 VELCRO HOOK —2
43— 031186— 3,15 POP RIVET ーB
42 068541 HEAD EXTENSION BOARD 一 1
41—067886—HEAD EXTENSION PLATE —4
40—031354— 1/4 FAT WASHER 一 +
39— 031175— 3/4 — 18 GA HOLE PLUG 一 2
38—058845— HEAD EXTENSION WELOMENT 一 1
37 —068644— PRE-0P/ POST-OP HEAD EXTENSION 一 1
36— 0313540 1/4 SAE FLAT WASHER 2
35— 035115— 395 1 x 3/4 0D. NYLON WASHER
34—068627— 50-275 HEAD SECTION PAD
33—057628— 20 x 5.0 VELCRO HOOK
2038— 1/4-20 x 3/4 BUTTON HD SOCKET SCR
1 — 031420— 10-24 x 3/4 SELF TAPPING SCR
30— 068309— HEADREST TOP COVER
29» O31451— 1/4-20 x 3/4 TRUSS HD MACHINE SUR
28—031428— 3/8-16 JAN НИТ
27 065809— 3/8-16 SOCKET HD SET SCR
067627 HEAD SUPPORT CABLE — SHORT
2641— 1/4 — RETARENG RING
167525 HEAD SUPPORT CABLE - LONG
1081 — 5/16 1D. SHIM WASHER
1344:
:65807— 3/8 x 3/8 SHOULDER BOLT
5796 — TEC KNOB
10-24 x 1/4 BUTTON HO SOCKET SCR 2
(4-20
x 3/4 FLAT SOCKET HO CAP SCR — 3
OPERATING LABEL
OPERATING LABEL ANGLE
HEAD FRAME COVER
ЮР COVER
MECHLOCK
6 —067620— COVER MOUNTNS PLATE
5 067614 HEAD SUPPORT FRAME,
4 —031324—1/4-20 x 1/2 FLAT SOCKET HD CAP SOR
3 — 06863 — SUPPORT PLATE MELDLENT
2 — 088832— HEAD BOARD
1 —068524— ASC275 BACK SECTION ASSY
EM [PART OlesPm [ov
PAGE 11

r HAUSTED' ASC
MODEL 375 HEAD SECTION
068541 HEAD
м EXTENSION PLATE
24—0313ğ4—1/4 FLAT WASHER
23— 031175—3/4 — 18 GA HOLE PLUG
72—068845— HEAD EXTENSION WELDENT
Bi GB HA PRE-OF/ FOST-OP HEAD 60060
20 06869— CAUTON LABE
19—087828— 20 3 50 K HOOK
18—088628— 200 "7
К о
16 —031102—1/4-20 x 1/4 SET SCREW
15—052049— SPRING
3 一 068620 END CAP
13065706 m 5/16-18 κ 5/8 "T" KNOB ASSBIBLY
12—C58518—- SLIDE KNOB
11—031055—5/4—20 LOCKNUT
10—088519—1/4—20 x 1,00 PEM FASTENER
9 — 068614 — HEADREST GUIDE
8 —066614—1/8 AVE
7 —068523—UBEL PLATE
$ — 0685 —" CENTER SECTION ASSEMBLY 1
4 —066925—1/4-20 x 1.00 FLAT SOCKET HD CAP SCR — +
3 068615 SUDE SUPPORT PLATE WELDMENİ 一 了
ュー058622 一 ASCS75 READ BOARD στι
1 —068304— ASC375 BACK SECTION ASS'Y =
IEMPARE NO|DEsRPHON om
PAGE 12

x’ HAUSTED’ ASC
WRIST WREST ASSEMBLES
ACCESSORY NO: SAO746
7 = 065959 WRIST REST SUS-ASSEUBLY =!
5 —031444—PAL CAP 一 1
5 = 056954— CLEMS PIN 一 1
056740 一 HINGE BAR ASSEMBLY 一 1
066738— KNOB 一 1
2 一 67849 SQUARE INSERT 一 4
1 = 067736— WRIST REST SUPPORT ASSEMBLY =
18404 no] DESCRIPTION [or
PAGE 13
ACCESSORY NO: SAO729
7 —057834— WRIST REST SUA-ASSEMÁLY =!
85 —031444—PAL CAP 一 1
5 —056954— CLEUS PIN 一 1
4 —065740— HINGE BAR ASSEUBLY 一 1
3-7 066738— KHOR 一 1
2 —067849— SQUARE INSERT 一 1
1—067756— WRIST REST SUPPORT ASSEMBLY =)
MPRT No| pescapnov am

İİ HAUSTED 1
RECOMMENDED
PROCEDURE SCHEDULE MATERIAL
LUBRICATE ALL MOVING AND SLIDING 6 MONTHS LUBRICATING OIL, LIGHT DUTY
PARTS AND HINGE POINTS. GREASE, WAX STICK LUBRICANT,
OR NEVER~SEEZ LUBRICANT.
INSPECT ALL FASTENERS TO INSURE 3 MONTHS PROPER SIZE WRENCH AND
PROPER FIT, POSITION, AND TIGHTNESS SCREWDRIVER.
(INCLUDING NUTS, BOLTS, ETC...)
CLEANING MATTRESS AND PADS PERIODICALLY | SOAP, WATER, AND MEDIUM
STRENGHT CLEANERS. {DO NOT
PRESSURE CLEAN}
INSPECT ALL SURFACES AND REMOVE | PERIODICALLY | METAL FILE, PROPER COLOR
ANY USER DEVELOPED SHARP OR PAINT (SPECIFY COLOR WHEN
BURRED AREAS. APPLY TOUCH-UP ORDERING)
WHERE REQUIRED.
CLEAN EXTERNAL SURFACES TO RE- | PERIDDICALLY | MEDIUM STRENGTH ANTI-
MOVE DIRT, LINT, BLOOD, AND ANY BACTERIAL CLEANERS, STAINLESS
OTHER DEPOSITS. STEEL CLEANER & POLISH
NOTE:
IF UNITS ARE PRESSURE WASHED, LUBRICATION OF ALL MOVING AND SLIDING
PARTS SHOULD BE DONE AFTERWARDS.
(STEAM CLEANING IS NOT RECOMMENDED AND CAN VOM) WARRANTY)
OPTIONAL ACCESSORIES
FOR FURTHER ASSITANCE IN PREVENATIVE MAINTENANCE OR TO ORDER ACCESSORIES PLEASE CONTACT
NUMBER DESCRIPTION NUMBER DESCRIPTION
TELESCOPING LV. ROD, 27° 10 50”
SADIO | SURGICAL RAIL APCO 人 8 。 | 2 SECTON。 WTH HOLDER, STAINLESS
HEEL STRRUPS MTH MOUNTING
SA0201 | ACCESSORY RAIL CLAMP apcozs | HER STR
KNEE CRUTCH LEG HOLDER MIH KNEE CRUTCHES WT MOUNTING
SADSIS | MOUNTING ADAPTOR APODZT | ADAPTORS
560414 | ARMBOARD WITH 1° PAD AND CLAMP APCMD — | OXYGEN TANK HOLDER
一 CUSTOM COLOR COMFORT CUSHIONS
SA0502 —_| SHOULDER ARTHROSCOPY SYSTEM APCSFT | DE GOREN FOREST GREEN STD
SA0548 | DOUBLE PKG. ARNTRAPS 6/CS 061280 | HEAVY DUTY 5” CASTERS
SHOULDER ARTHROSCOPY SYSTEM
SA0563 | HD AR 08887 | PATENT TRAY
SAO729 | LATERAL ACCESS SURGEON WRIST 28450 | VERNCAL OXYGEN TANK HOLDER
FULL SURGEON (OVER THE BROW) :
SA0746 | {ULE SURGE 150080 | PAPER ROLL HOLDER
apcot2 | RESTRAINT STRAPS WITH VELCRO
HAUSTED
927 LAKE ROAD, P.O. BOX 710 MEDINA, OHIO 44258
(216) 723—3217
PAGE 14
1-800—428—7833