Havis-Shields K9/Prisoner Transport Unit KK-K9-C20-K-PT User manual

INSTALL INSTRUCTIONS KK-K9-C20-K-PT
K9/PRISONER TRANSPORT UNIT
2007-2008 CHEVROLET/GMC TAHOE/YUKON
TOOLS REQUIRED:
Ratcheting wrench
Socket & Metric socket sets
Drill bit set
Powered drill
Screwdriver set
HARDWARE:
QTY DESCRIPTION PART #
20 ¼-20 x ½” Stainless arriage Bolts GSM32022
30 ¼-20 x ¾” Stainless arriage Bolts GSM32024
50 ¼-20 Hex Flange Serrated Nuts Zinc GSM30023
6 ¼” x 1” Hex Head Lag Bolt GSM33060
22 #12 x ¾” Stainless Sheet Metal Screws GSM34177
24 #10 x ¾” Sheet Metal Screws Stainless GSM34170
12 #10 x ½” Sheet Metal Screws Stainless GSM34169
10 10-32 x ¾” Machine Screw Screws Stainless GSM34098
6 #10 x ¾” Sheet Metal Screws Zinc GSM33195
1 Tube Silver aulk PRM97343
COMPONENTS:
QTY DESCRIPTION PART #
1 Main K9 housing assembly KK-K9- 14-K-DS
1 K9 Tunnel assembly KNM02038- 14
1 Driver-side floor mounting bracket KNM01081- 14
1 Passenger-side floor mounting bracket -3061-9
2 Passenger-side “B” pillar mounting brackets -3061-5 and -3061-7
1 Upper prisoner filler panel KNM001213
1 Rear prisoner filler panel KNM000977
1 Lower prisoner filler panel KNM001207
1 Front prisoner filler panel KNM000978
1 Front prisoner seal panel KNM001220
1 32” x 45” x 3/16” Rubber Mat KNM01029-SUV

KK-K9- 20-K-PT_INST_10-07
A ways!
 Read all instructions before installing any Havis-Shields Equipment orp products
 Disconnect the vehicle battery. Removing seat bolts on some vehicles may give the vehicles
computer a false reading, causing a warning light on the instrument cluster. This requires the
vehicles’ computer to be reset with a vehicle diagnostics tool.
 Check for obstructions (Wire, brake ines, fue tank, etc.) before dri ing any ho es!
 Use only hardware provided with install kit.
 For product support, visit the Install Instructions Section of our website at
http://havis.com/Installation/Installation.html, email [e-mail] or call 1-
800-524-9900 and ask for technical support.
***CAUTION!!! ON PASSENGER SIDE REAR, UNDER THE VEHILCE, ARE
REFRIGERANT LINES THAT MAY LINE UP WITH REAR PARTITION FILLER PANEL
DO NOT DRILL THROUGH VEHILCE IN THIS LOCATION
K9
Assembly
Front prisoner
filler panel &
Front prisoner
seal panel
Upper prisoner
filler panel
K9 tunnel
assembly
Rear prisoner
filler panel
Passenger-side “B” pillar
mounting brackets
Two “L” Brackets
See photos
Driver-side floor
mounting bracket
Passenger-side floor
mounting bracket
Lower prisoner
filler panel

KK-K9- 20-K-PT_INST_10-07
Remove dual passenger
seat assembly
Leave the single
passenger-side seat
installed
Remove passenger door
panels, door handles and
speakers Note: Reconnect
window switches and wire
tie parts so they do NOT
interfere with window
operation.
Note: Wrap OEM switch
with P astic bag to
protect from water
Remove “B” Pillar Trim, Seat belt bolt and Grab Handle
Reuse OEM Grab handle bolts and attach “L” brackets to grab handle mount holes

KK-K9- 20-K-PT_INST_10-07
Attach to existing seat
bolt studs with O.E.M
seat bolt nuts
Slide in Main K9 Housing and rest on mounting feet.
Assemble Mounting feet to floor plates in
locations shown above
Set height at 7.5”
Passenger-side Driver-side
1. Mount 7” bracket at Top and 5” bracket at bottom
2. Seat belt mount bracket lower tab may need to be slightly bent out of the way
3. Reattach seat belt bolt and trim and ut Plastic Trim at “L” bracket if necessary.
4. Mount Partition to “L” brackets.

KK-K9- 20-K-PT_INST_10-07
Line up driver and passenger-side floor mounting brackets and loosely
attach to K9 main housing, using ¼” x ¾” stainless carriage bolts and
serrated nuts.
**Do not tighten hardware unti the side tunne is set in p ace**
Attach driver side tunnel with ½” long and ¾ “ long
carriage bolts. Position K9 unit so tunnel lines up with
rocker panel plastic trim. Move driver seat to rear most
position.
Attach upper prisoner
filler panel using ex
isting
¼ x ¾” stainless carriage
bolts and serrated nuts

KK-K9- 20-K-PT_INST_10-07
1. Attach front floor mounting bracket
to forward prisoner filler panel using
¼” x ¾” carriage bolts and nuts.
2. Attach to vehicle using ¼” x 1” hex
lag bolts. Be sure to check for
obstacles.
Flip front portion of seat out of the
way and attach lower prisoner filler to
K9 main housing, using #10 x ½”
sheet metal screws.
Caution…A ways Check under vehic e for obstructions
1.
Attach front prisoner filler panel to K9 main housing
using ¼ x ¾” stainless carriage bolts and serrated nuts.
2. Attach front prisoner partition to previously mounted
“B” pillar mounting brackets using ¼ x ¾” stainless
carriage bolts and serrated nuts.
#1
#2
1
.Attach rear prisoner filler
panel to K9 main housing
using ¼ x ¾” stainless
carriage bolts and serrated
nuts.
2
.Attach to floor using ¼” x
1” hex head lag bolts. Be
sure to check under vehicle
for obstacles.
#1
#2

KK-K9- 20-K-PT_INST_10-07
With door panel installed, hold up window guard assembly with top
bracket between rubber and metal frame. Guard hinge will sit on
top of door panel. Mark location of top bracket and hinge.
Remove top bracket
from window guard
Hold top bracket in its location, mark the four mount holes and
drill with 1/8” drill bit. arefully hold rubber gasket away from
drill. Drill 1/8” holes for hinge mounting. Attach Top bracket
and hinge with #10 x ½” sheet metal screws.
Hinge up window guard and
attach to top bracket with 10/32 x
½ machine screws
Final Door
panel and
window
guard
assembly
enter door panel on door.
Push down and drill mount
holes with 1/8” bit. Attach with
#10 x ¾” Sheet metal screws