Havis-Shields Ford Van Rear Air Vent Adapter Kit KK-F-VAK Configuration guide

INSTALL INSTRUCTIONS for KK-F-VAK
FORD VAN REAR AIR VENT ADAPTER KIT
TOOLS REQUIRED:
Ratcheting wrench
Standard & Metric Socket Set
Screwdriver set
Wire cutters
HARDWARE:
QTY DESCRIPTION PART #
1 Heat/Cool Adaptor box assembly KKM01152
1 Ford Rear Air Hose Adapter KKM01153
1 Ford Heat/Cool Box mounting channel KKM99071
10 Hose Clamps 3” GSM20045
2 4” Hose Clamps GSM20042
4’ 4” Diameter Hose GSM40100
4 Vent cover w/ hose adapter assembly KKM0403-001
1 2 ½” “Y” Duct Connector PRM97483
1 2 ½” Air Duct Hose 8 foot length PRM97475
1 2 ½” Air Duct Hose 7 foot length PRM97475
1 2 ½” Air Duct Hose 6 foot length PRM97475
2 2 ½” Air Duct Hose 4 foot length PRM97475
20 #10 X ¾” Sheet Metal Screws GSM33195
20 #10 Star Washers GSM31034
20 #10 x ¾” Flat Head Sheet Metal Screws GSM34151
20 15” Wire Tie GSM20036
Always!
¾Read all instructions before installing any Havis-Shields Equipment Corp products.
¾Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
¾Use hardware provided with install kit
¾For product support, visit the Install Instructions Section of our website at
http://havis.com/Installation/Installation.html, email [email protected] or call
1-800-524-9900.

KK-F-VAK_INST_10-08
2
Remove the hex head screw on
the vent cover Remove the vent cover mpletely. It will not be re-useco d. l
Remove the hex head lag bolt
ocated above the blower motor of
the OEM rear HVAC unit
Remove the hex head lag bolt
holding the intake cover of the
OEM rear HVAC unit
Remove the hex head screws on
the intake cover Remove the intake cover. Intake cover will not be re-used.
Attach the HVAC hose and
clamps to the plenum assembly View of the components at this
point of the installation Place the unit as shown above

KK-F-VAK_INST_10-08
3
Align the assembly so the hole in
the assembly lines up with the “J
clip”. Re-attach using the hex
head lag bolt removed earlier
At the intake side of the OEM
unit, attach the hose plate as
shown above using (2) #10 x ¾”
sheet metal screws
Attach the (2) #10 x ¾” sheet
metal screws at the location
shown above. Pre-drill 1/8” hole
Route hose straight up from the HVAC
unit and tie tight to the corner of the van
Tighten the clamp that holds the
hose to the assembly
Now the HVAC adapter kit is
fastened to the OEM unit.
When routing the hoses, tie together
using 15” wire ties, to keep a neat and
tight fit to the wall of the vehicle. This
will minimize the risk of damage when
installin
g
Kwik-Kit
Attach the intake hose and clamp
to the HVAC adapter box

Attach the “Y” duct hose adaptor to
the 8 foot front duct hose and
connect both 4 foot hoses from “Y”
to vents in driver and passenger side
front ceiling. This will provide a
total of four ceiling vents.
Route HVAC 2 1/2” blower hoses to
the approximate locations with tape
along ceiling where they will be
installed into the ceiling insert after
Kwik-Kit insert is installed. Mount
hoses with wire ties at wall and ceiling
corners only. Leave enough slack to
reach hoses for permanent mounting.
During Kwik Kit installation you will be
prompted to return to the KK-F-VAK
instruction to attach the hose to the vent
adapter brackets. Route hose into ceiling holes
and cut off any extra slack. Attach the hose to
the vent bracket using a 3” hose clamp
Align the three mount holes of the vent adapter
cover with the pre-punched holes in ceiling.
Attach each vent to ceiling using #8 x 3/8” flat head
sheet metal screws.
(Screws included with standard Kwik kit hardware)
KK-F-VAK_INST_10-08
4