Havis-Shields Slide-Out Trunk Tray 2006-2008 Chevrolet Impala... Configuration guide

- 1 -
INSTALL INSTRUCTIONS C-3311-2 & C-3311-18-2
SLIDE-OUT TRUNK TRAY
2006-2008 CHEVROLET IMPALA
TOOLS REQUIRED:
7/16” wrench
Powered drill w/ 3/16” drill bit
Ratcheting wrench
Standard socket set
Screwdriver set
HARDWARE:
QTY DESCRIPTION PART #
12 ¼-20 x ¾” Hex head bolts GSM33001
16 ¼” Flat washers GSM31005
12 ¼-20 Serrated nuts GSM30023
4 8-32 x 3/8” Machine Screws GSM33540
4 8-32 Keps Nuts GSM30027
4 ¼” x ¾” Hex head lag bolts (only on C-3311-18-2) GSM33060-1
2 Front Mounting Leg CM001390
1 Rear Driver-side bracket CM001391
1 Rear Passenger-side bracket CM001392
4 Mounting plate w/ pem ¼” pem studs (Use 2 on C-3311-18-2) CM001393
1 P.S. Front Mounting Bracket (only on C-3311-18-2) CM001394
1 P.S. Rear Mounting Adapter Bracket (only on C-3311-18-2) CM93712
Always!
 Read all instructions before installing any Havis-Shields Equipment Corp products.
 Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
 Use hardware provided with install kit
 For product support, visit the Install Instructions Section of our website at
http://havis.com/Installation/Installation.html
SUB ASSEMBLY: (Use Iso views on page #1 & 2 for sub assemblies)

- 2 - C-3311-2^3311-18-2_INST_9-07
8-32 Screws
and hex nuts
D.S. Rear Mounting
Brackets
Front Mounting
Legs
P.S. Rear
Mounting Bracket
Mounting Plate
Mounting Plate
Cradle Bracket
C-3311-2 FULL SIZE SLIDE TRAY
P.S. Rear
Mounting Bracket
8-32 Screws
and hex nuts
D.S. Rear Mounting
Brackets
Front Mounting
Legs
Mounting Plate
P.S Front
Mounting Bracket
P.S. Rear Mounting
Adapter Bracket
C-3311-18-2 HALF SIZE SLIDE TRAY
¼” x 1”
Lag bolts
¼” x 1” Lag bolts

- 3 - C-3311-2^3311-18-2_INST_9-07
1. Attach forward mounting legs to the slide out tray.
• Attach forward mounting legs with provided 8-32 screws and hex nuts to slide track.
• The front legs will be square to the slide tray.
• On the front passenger side of the half tray, passenger side front mounting brackets
(CM001394) will attach to the front mounting legs.
2. Attach rear-mounting brackets to the slide out tray.
• Loosely attached the rear mounting brackets to the “Cradle Bracket” using ¼” x ¾”
hex head bolts, washers and serrated nuts.
• On the rear passenger side of the half tray, passenger side rear mounting adapter
bracket (CM93712) will attach to the rear mounting brackets.
INSTALLATION:
1. Mount slide tray in vehicle trunk.
• Slide trunk tray into vehicle with the tall front mounting legs in first. Prop up tray in
position using block of wood.
• Once you have the tray square, and pushed to the forward most position in trunk,
attach mounting brackets to vehicle using the supplied mounting plates.
• On the half tray, passenger side, you will bolt the passenger side front mounting
brackets (CM001394) to the vehicle using ¼” x ¾” Hex head lag bolts. (Pre-drill w/
3/16” drill bit)
• Position mounting plates into locations shown in photos #1 and 2.
• Loosely attach front and rear mounting brackets to mounting plates using ¼” serrated
nuts.
• On the passenger side, attach passenger side rear mounting adapter brackets
(CM93712) to vehicle using ¼” x ¾” hex head lag bolts. (Pre-drill w/ 3/16” drill bit)
Mounting
Plate
Forward Mounting Brackets
Mounting
Plate
Rear mounting brackets
Photo #1
Photo #2

- 4 - C-3311-2^3311-18-2_INST_9-07
• Tighten all loose hardware.
• Be sure tray slides smoothly and locks in the closed position. If the tray does not slide
smooth then most likely the tray is not square or level.
P
hoto #3
#8 screws &
hex nuts
¼” bolts, washers,
& nuts