Havis-Shields Chevrolet Van Rear Air Vent Adapter Kit... User manual

INSTALLATION INSTRUCTIONS for KK-C-VAK
CHEVROLET VAN REAR AIR VENT ADAPTER KIT
TOOLS REQUIRED :
Screw Driver Set
Ratcheting Wrench Set
Standard Socket Set
Power Drill
Drill Bit Set
Safety Goggles
HARDWARE / COMPONENTS:
QTY DESCRIPTION PART #
1 Heat/Cool Ada tor box assembly KKM01152
1 Chevy Heat/Cool Box mounting channel KKM01147
1 Chevy Rear Air Hose Ada ter KKM01148
10 Hose Clam s 3” GSM20045
2 4” Hose Clam s GSM20042
1 4” Diameter Hose GSM40100
4 Vent cover w/ hose ada ter assembly KKM0403-001
1 2 ½” “Y” Duct Connector PRM97483
1 2 ½” Air Duct Hose 8 foot length PRM97475
1 2 ½” Air Duct Hose 7 foot length PRM97475
1 2 ½” Air Duct Hose 6 foot length PRM97475
2 2 ½” Air Duct Hose 4 foot length PRM97475
20 #10 X ¾” Sheet Metal Screws GSM33195
20 #10 Star Washers GSM31034
20 #10 x ¾” Flat Head Sheet Metal Screws GSM34151
20 15” Wire Tie GSM20036

KK-C-VAK_INST_10-07
Alwa s!
 Read all instructions before installing any Havis-Shields Equi ment Cor roducts.
 Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
 Use hardware rovided with install kit
For product support, visit the Install Instructions Section of our website at
http://havis.com/Installation/Installation.html, email [email protected] or call
1-800-524
Note: This procedure must be done PRIOR to the Kwik Kit installation and is
recommended to check the flow of Air through the hoses prior to installation of Kwik-
Kit unit
SUBASSEMBLY:
1. Remove all necessary arts from shi ing ackages and verify arts.
2. Remove AC and Heat lastic vents from OEM - HVAC blower ducts.
3. If vehicle has full rear trim, you must remove trim anels around the OEM - HVAC unit
including ductwork / headliner. NOTE: The front ortion of headliner can be cut off and reused
as front ceiling trim after com lete kit is installed.
INSTALLATION:
Connect Plenum (rectangle blower ada tor)
to the O.E.M
. blower ducts using #10 x ¾”
Sheet Metal Screws and #10 star washers .
There are two (2) ducts on the factory HVAC
unit. One at rear is for air conditioning and
one forward is for heat. The 4” blue hose
connects heat into the new lenum.

KK-C-VAK_INST_10-07
Route HVAC 2 1/2” blower hoses to the
a roximate locations with ta e along
ceiling
where they will be installed into the
ceiling insert after Kwik-Kit insert is
installed. Mount hoses with wire ties at
wall and ceiling corners only. Leave
enough slack to reach hoses for ermanent
mounting.
Attach the “Y” duct hose ada tor to
the 8 foot front duct hose and
connect both 4 foot hoses from “Y”
to vents in driver and assenger side
front ceiling. This will rovide a
total of four ceiling vents.
Route hose straight u from the HVAC unit
and tie tight to corner of the van
When routing the hoses, tie together using
15” wire ties, to kee a neat and tight fit to
the wall of the vehicle.
This will minimize the risk of damage when
installing Kwik kit

KK-C-VAK_INST_10-07
During Kwik-Kit installation you will
be rom ted to return to the KK-C-
VAK instruction to attach the hose to
the vent ada ter brackets. Route hose
into ceiling holes and cut off any extra
slack.. Attach the hose to the vent
bracket using a 3” hose clam
Align the three mount holes of the vent ada ter cover
with the re- unched holes in ceiling.
Attach each vent to ceiling using #8 x 3/8” flat head
sheet metal screws.
(Screws included with standard Kwik-Kit hardware)
After Al
uminum insert is installed and tested,
attach cover late to bench / wall to cover
OEM Rear AC/Heat Unit using #10 Sheet
metal screws.
Check that airflow through hoses is
working ro erly.
With hoses routed to locations, roceed
to install Kwik-Kit unit until you come
to the ceiling instructions. Be sure not
to uncture the hoses with screws, drill
bits, etc…
Attach ceiling ieces on Kwik-Kit,
routing hoses into the corres onding
holes in Kwik-Kit ceiling. Pull through
to minimize slack.
Check airflow again.