Haworth Upside User manual

GROUNDED
OUTLET
GROUNDED
OUTLET BOX
GROUNDED
FIGURE 1
PIN
Maximum Load rating including surface: 250 lbs
IMPORTANT SAFETY INSTRUCTIONS
For use with UPSIDE Electric Height Adjustable Tables, 2 Leg
For Commercial or Household Use Only
This product conforms to UL962 and is certied to CAN/CSA C22.2 No. 68.
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this table.
DANGER- To reduce the risk of electric shock:
1. Always unplug this furnishing from the electrical outlet before cleaning or servicing.
WARNING: TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recom-
mended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, turn all controls to the o position, then remove plug from outlet.
9. WARNING: RISK OF ELECTRIC SHOCK - CONNECT THIS FURNISHING TO A PROPERLY GROUNDED
OUTLET ONLY. SEE GROUNDING INSTRUCTIONS.
10. WARNING: RISK OF ELECTRIC SHOCK, FIRE, AND INJURY. REVIEW THE ASSEMBLY INSTRUCTIONS TO
CONFIRM THAT THE APPROPRIATE CRITICAL COMPONENTS AND ACCESSORIES ARE BEING USED WITH THE
FURNISHING.
SAVE THESE INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER- Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or serviceman if you are in doubt as to whether the product is properly grounded.
Do not modify the plug provided with the product - if it will not t the outlet, have a proper outlet installed by a
qualied electrician.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in sketch A
(see Figure 1). Make sure that the product is connected to an outlet having the same conguration as the plug. No adapter
should be used with this product.
Electrical Rating:
120V, 60Hz, 6.25A for Upside+ 2 leg tables
120V, 60Hz, 6A for Upside 2 leg tables
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
51 of 30 6100-0110
245-789

S201
2 of 30
Tools Required
Height Adjustable Tables, 2 Leg
Installation Instructions
UPSIDE®
#2
Scale 1 : 1
0 11/2
1/4 1/4
3mm
4mm
#2
13mm
A
S200
S209
S202 S201
S201
S200
B
B
H
H1
D
F
G
J
D
E
E.C.O. No: Rev:
Part No:
Page:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
IMPORTANT!
PRIOR TO FIRST USE, PERFORM A
DEFAULT RESET TO SYNCHRONIZE THE
MOTORS IN THE COLUMNS (D). SEE
DEFAULT RESET INSTRUCTIONS IN THE
“OPERATING YOUR UPSIDE
HEIGHT-ADJUSTABLE TABLE” SECTION.
(S-90) 3mm
M6 X 8mm Set Screw
M6 X 10mm Button Head
(S200) 4mm
M4 - 30mm Pan Head Screw
(S206)
(S209)
M6 X 14mm Button Head
4mm
(S201)
M5 X 20mm Pan Head Screw
(S202)
M5 X 16mm Pan Head Screw
H1 H1
1/8” Drill Electrical Tape
OR
OR
OR
STANDARD
CENTER
RAIL
S201
C
S206
C2
VALUE
CENTER
RAIL
5
245-789

3 of 30
D
H
1
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
3
3
2
2
A
IMPORTANT!
INSTALL CHANNEL (H1)
AS SHOWN! - SLOT
FACING IN AND NOTE
POSITION OF LONG
TAB!
IMPORTANT!
INSTALL CHANNEL (H1)
AS SHOWN! - SLOT
FACING IN!
IMPORTANT!
INSTALL SCREWS (S200)
LOOSELY!
M6 X 10mm Button Head
(S200) 4mm
LONG TAB
H1
1
3
3
H
H1
1
TIGHTLOOSE
H1
H1
H1
H1
S200
NOTE: Slide rail (H1)
to view holes.
OR
OR
5
245-789

4 of 30 Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
S200
A
D
B
2
1
1
M6 X 10mm Button Head
(S200) 4mm
IMPORTANT!
TIGHTEN ALL 12
SCREWS (S200)!
TIGHT
2
S200
S200
5
245-789

3A
3B
5 of 30
S201
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
OR
OR
(S201)
M5 X 20mm Pan Head Screw
FOR T-LEG BASE (2 SCREWS)FOR C-LEG BASE (3 SCREWS)
Y
DD
X
C-Style
576
42
70 -
305 MAX.
WORKSURFACE (mm)
D
Y
X
C-Style
728
88
70 -
305 MAX.
T-Style
576
51
70 -
305 MAX.
T-Style
728
127
70 -
305 MAX.
C-Style
22-11/16
1-5/8
2-3/4 -
12 MAX.
WORKSURFACE (inches)
D
Y
X
C-Style
28-11/16
3-7/16
2-3/4 -
12 MAX.
T-Style
22-11/16
2
2-3/4 -
12 MAX.
T-Style
28-11/16
5
2-3/4 -
12 MAX.
Y
X
NOTE: Use bracket (B)
as template and predrill
holes.
1/4”
1/8”
Drill
5
245-789

5
6 of 30 Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
D
A
E
S209
(S-90) 3mm
M6 X 8mm Set Screw
(S209)
M6 X 14mm Button Head
4mm
S-90
4
S201
IMPORTANT!
MAKE SURE
SETSCREWS (S-90)
ENGAGE RAILS (H1)
H
H1
H1
(S201)
M5 X 20mm Pan Head Screw
NON-LOCKING CASTER
LOCKING CASTER
NOTE: Casters are Optional
and ordered separately.
5
245-789

OR
IMPORTANT!
MAKE SURE CONTROL BOX (F)
IS FIRMLY ATTACHED TO THE
WORKSURFACE!
A
F
F
6
S201 S202
OR
S201 S202
F
F
G
G
J
D
OR
NOTE: For frame (H) less than 46 inches wide
mount control module (F) outside of frame
(H) as shown.
H
IMPORTANT!
PLUG IN CABLE (D)
INSTALL SCREWS (S202)
INSTALL CABLE (J)
1
2
3
1
2
3
J
(S202)
M5 X 16mm Pan Head Screw
46” AND SMALLER
7 of 30 Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
(S201)
M5 X 20mm Pan Head Screw
(S202)
M5 X 16mm Pan Head Screw
(S201)
M5 X 20mm Pan Head Screw
5
245-789

Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
8 of 30
7
S206
C2
S201
C
C1
2
3
4
5
6
M4 - 30mm Pan Head Screw
(S206)
NOTE: Paddle screw (S206) must be installed straight
and fully seated. Crooked or partial installation of
screws (S206) may interfere with the paddle (C)
performance (both standard and programmable).
GOODBADBAD
C2C2C2
S206
S206S206
NOTE: Use template on the following
pages to help locate paddle (C).
PROGRAMMABLE
PADDLE
STANDARD
PADDLE
OR
PROGRAMMABLE
PADDLE
STANDARD
PADDLE
OR
C2
C
30.0
OR
OR
C2
C
(S201)
M5 X 20mm Pan Head Screw
30.0
5
245-789

1/4”
1/8”
Drill
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
9 of 30
7FLIP TABLE OVER
IMPORTANT!
PRIOR TO FIRST USE,
PERFORM A DEFAULT
RESET TO SYNCHRONIZE
THE MOTORS IN THE
COLUMNS (D). SEE
DEFAULT RESET
INSTRUCTIONS IN THE
“OPERATING YOUR
UPSIDE
HEIGHT-ADJUSTABLE
TABLE” SECTION.
TEMPLATE - PADDLE
OR
C
FRONT EDGE OF WORKSURFACE
2.07
[53mm]
3.11
[79mm]
NOTE: After drilling pilot holes,
return to previous page to
complete table installation.
30.0
5
245-789

TEMPLATE - STANDARD PADDLE
TEMPLATE - PROGRAMMABLE PADDLE
1.46
[37mm]
1.024
[26mm]
1.693
[43mm]
2.48
[63mm]
1.979
[50mm]
1.50
[38mm]
.709
[18mm]
.866 [22mm]
2.21
[56mm]
1.119 [28mm]
FRONT EDGE OF WORKSURFACE
FRONT EDGE OF WORKSURFACE
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
10 of 30
Scale 1 : 1
0 11/2
1/4 1/4
IMPORTANT!
CHECK SCALE
BEFORE USING
TEMPLATE!
MAKE SURE IT IS
TO SCALE! WHEN
PRINTING: SET
YOUR PRINTER
TO PRINT
“ACTUAL SIZE”!
1/4”
1/8”
Drill
1/4”
1/8”
Drill
NOTE: After drilling pilot holes,
return to previous page to
complete table installation.
NOTE: After drilling pilot holes,
return to previous page to
complete table installation.
5
245-789

Upside Table
Troubleshooting Guide
Complete
Table height adjustment issue
START
Does performing
a reset resolve
the issue?
Does a
programmable
paddle screen
illuminate when
pushed?
Table does not move
when I try to reset
Yes No
Yes
No
Go to Power
page.
Yes
No
Does the table
continue moving
after releasing
the paddle?
Remove paddle.
Drill new pilot
holes using paddle
template. Reinstall
paddle screws
ensuring they are
perpendicular to
the work surface.
Yes
No
Yes
No
Does the table
start moving,
then reverse
direction for a
moment?
Go to Collision
Detection page.
Go to Installation
check page.
Does a
programmable
paddle display
an error
message?
Go to Errors
page.
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
26 of 30
Note: Parts of this quide require a programmable paddle handset, service part # 8754-8401.
5
245-789

Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
27 of 30
Yes
Yes
No
Yes
No
Yes
No
No
Upside Table
Collision Detection
Is the path of motion of
the table and attached
accessories completely
clear of obstructions on
all sides, including wires?
Is the control box snugly
fastened to work
surface?
Are all the wires for the
table secured snugly to
the frame or
worksurface?
Does removing load
from the table top
resolve the issue?
Maintain lower load
when adjusting table
Remove obstacles
Ensure control box is secured
tightly and is at against the
underside of the work surface.
Tighten screws so that control
box cannot rock or move.
Secure wires using
provided adhesive cable
ties
Lower collision detection
sensitivity setting on
control box (refer to user
instructions)
From
troubleshooting
start page
5
245-789

Upside Table
Errors
Leave table plugged into wall and idle
for 20 minutes. (Table is intended to run
maximum of 2 min on + 18 min o)
Yes
No No
“H01” Duty cycle
protection error?
Perform a
second reset
Yes
Does error
re-occur after
running the table
up & down?
Complete
NoYes
Yes
Perform a third
reset. Does error
reoccur after
running the table
up & down?
Measure the
height of both
columns. Are they
more than 3/4”
dierent?
Did the error
message change? Complete
No
No
Yes Replace
control box
Replace both
columns
From front
page
E01
LOC
E08
E07
E02
M1 overcurrent protection
Handset locked
M2 Hall eect sensor
M1 Hall eect sensor
M2 overcurrent protection
1) Identify which column is plugged
into M1 port on control box
2) Reduce load over M1 column
1) Identify which column is plugged
into M2 port on control box
2) Reduce load over M2 column
1) Replace handset
2) Unplug table for 20 seconds and
plug back in
1) Unplug and re-plug M1 cable
1) Unplug and re-plug M2 cable
Error Description Troubleshooting steps
1) Swap cables in M1 and M2
2) Perform a reset & run
table up and down
Replace column
that is plugged
into port with
error message
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
28 of 30 5
245-789

Yes
No
Yes
No
Yes
No
Upside Table
Power
Is the power cord rmly
plugged into the wall
outlet and control box?
Is the wall outlet
powered? (Do other
devices power up when
plugged in?)
Is the paddle rmly
plugged into the control
box?
Plug in power cord
Resolve power issue
Plug in paddle
Replace control box -or-
Replace paddle
From
troubleshooting
start page
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
29 of 30 5
245-789

Yes
No
No
Yes
Upside Table
Installation Check
Is table level?
Issue resolved?
Level table by
adjusting glides
Complete
Contact Haworth
corrections
Perform a reset
1) Unplug table and remove everything from top
2) Flip table onto soft, clean surface
3) Loosen all frame screws
4) Tighten all frame screws
5) Flip table
6) Plug in table
From
troubleshooting
start page
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
6100-0110
30 of 30 5
245-789