Hay Loop Stand Table User manual

1
By LEIF JØRGENSEN
> INSTRUCTION MANUAL <
H AY
LOOP STAND TABLE

2
> INTRODUCTION <
Loop Stand is Leif Jørgensen’s well-designed and
ultra-functional, no-nonsense series of coat stands, wardrobe
furniture and tables, all with a consistent family identity.
Loop Stand Table shares the same clean visual expression
as the wardrobe stand, where the characteristic three-legged
trestles are attached to the tabletop with screws.
The Loop Stand Table is available in several variants and
heights to suit a wide range of dining rooms and offices in
corporate and private settings.

> CARE AND MAINTENANCE <
LINOLEUM
• Clean with a clean cloth wrung in water or in a solution
of water and a neutral detergent or soap flakes. Remove
soap residue immediately using a clean, dry cloth.
• If the surface is scratched or appears matt, use a care
product suited especially for linoleum.
• Stains may be carefully removed using white spirit
(mineral spirit) or a damp nanosponge dipped in luke-
warm water or linoleum care. Follow up immediately with
a clean, dry cloth. Never use the nanosponge dry.
• Avoid alkaline detergents such as soft (yellow) soap,
washing soda, lye and scouring powder.
LAMINATE
• Clean with a clean cloth wrung in water or in a solution
of water and a neutral detergent. Remove soap residue
immediately using a clean, dry cloth.
• Stains may be carefully removed using household
ammonia or with a clean, damp cloth or a nanosponge
wrung in warm water. Never use the nanosponge dry.
Follow up immediately with a clean, dry cloth.
• Avoid using scouring cream or scouring pads, as they
may scratch the surface.
POWDER COATED STEEL
• Clean with a clean cloth wrung in water or in a solution
of water and a neutral detergent. Remove soap residue
immediately using a clean, dry cloth.
• Avoid using scouring cream or scouring pads, as they
may scratch the surface.
> CARE AND MAINTENANCE <
CAUTION
With a little care you can prolong the life of your
furniture. Follow the instructions for the materials of
your specific product to make sure that it stays in the
best shape for as long as possible.
The information below is only intended as a
general guideline. For more information on how to
remove specific stains, please inquire where you
bought the furniture.
• Always remove stains quickly before they can do any
permanent damage to the furniture.
• Avoid placing the furniture in direct sunlight or near a
strong heat source to reduce changes.
• When you move the furniture, make sure to lift it rather
than pulling or pushing it to avoid damaging the floor,
legs and mountings.
• Tighten up the screws after one to two months’ use
and when required .
• Avoid improper use such as putting your feet on the
table or standing on it.
• Use coasters under damp, hot or coloured objects to
avoid permanent stains.
• Be careful not to scratch or damage the surface with
sharp objects.
• Avoid covering the surface partially, for example with
tablecloths or place mats, as colour variances may
appear.

6 7
> CONTENTS<
Page 8 - 11
L160/180/200 cm
Page 12 - 17
L250 cm - Crossbar extention
Page 18 - 21
Loop Stand Support
CAUTION
While assembling, keep the tabletop inside the cardboard box with edge foam to protect the
tabletop from scratches etc. Make sure that all parts are included.

8 9
> RECOMMENDED TRESTLE PLACEMENT<
160cm
100cm27cm
180cm
120cm27cm
37cm
200cm
120cm
A x 1 B x 2
C x 4
> L160/180/200 CM /PARTS<

10 11
2.
Place the tabletop on the trestles according to the recommended trestle placement.
Screw the C parts through the trestles and into the tabletop.
Mount the table standing upright.
3.

12 13
A x 1 C x 2B x 2
D x 12
> L250 CM /PARTS <
37cm
250cm
50cm
92,5cm
14cm
> RECOMMENDED TRESTLE PLACEMENT<

14 15
2.
Screw the B parts to the tabletop using the D parts.
Flip the tabletop.
4.
Place the tabletop on the trestles according to the recommended trestle placement.
Screw the D parts through the trestles and into the tabletop.
Mount the table standing upright.

16 17
5. CAUTION
When moving the table, please lift the table rather than pushing it.
If the table is out of balance, please spread the trestle legs in order to align the legs.
Spread the trestles in order to align the legs.

18 19
> LOOP STAND SUPPORT /OPTIONAL <
100cm
120cm
170cm
D x 1
E x 4
E x 4
E x 4
F x 8
F x 8
F x 12
1.
Place the trestles standing upright, and slide in the support (D) using the E parts.
Do not tighten the E parts completly in order to slide in the support (D).

20 21
2.
Tighten the E part to secure the support (D) to the trestle.
3.
Screw the support (D) into the tabletop (A) using the F parts.
3.

22 2322

24
Havnen 1 8700 Horsens Denmark
[phone] / [e-mail]
H AY
ITEM NO. 706353
19042017
710441 2458585