Hayman Reese 03267RW User manual

HAYMAN REESE
PART No: 03267RW
MITSUBISHI TRITON MQ MY19 CL4 UTE
INSTALLATION INSTRUCTIONS
PLEASE ENSURE THAT ALL INSTRUCTIONS ARE UNDERSTOOD PRIOR TO FITMENT
PLACE THESE INSTRUCTIONS IN THE VEHICLE’S GLOVEBOX AFTER INSTALLATION IS COMPLETED
Towbar Installation Instructions Towbar capacity
MITSUBISHI TRITON MQ MY19 CL4 UTE
Part Number 03267RW Max Towing Braked 3100 kg
Max Towing Unbraked 750 kg
Max Static Ball Load 310 kg
Installation Time: Approx 30 Mins
Hayman Reese (Cequent)
PO Box 4050, Dandenong South VIC 3164
Phone [phone] Email [e-mail]

HAYMAN REESE
PART No: 03267RW
MITSUBISHI TRITON MQ MY19 UTE
INSTALLATION INSTRUCTIONS
PLEASE ENSURE THAT ALL INSTRUCTIONS ARE UNDERSTOOD PRIOR TO FITMENT
PLACE THESE INSTRUCTIONS IN THE VEHICLES’S GLOVEBOX AFTER INSTALLATION IS COMPLETED
Rev: A Page 2 Issue Date: 25-01-2019
Warning:
1. Do not, drill, cut, weld or otherwise modify the towbar.
2. If you are using electric welding on a motor vehicle, always check that the vehicle is not equipped with electronic
engine or instrument management equipment. Failure to do so could destroy any onboard computers. If in
doubt, check with the vehicle's manufacturer.
3. If TBM is used in inverted position tow ball may make contact with rear tailgate when lowered, which could cause
damage.
General:
1. Ensure all hardware items have been included refer to assembly diagram.
2. It is recommended that the instructions are read through and completely understood before making any attempt
to fit this product.
3. Be wary of any changes to vehicle designs or other accessories that may conflict with the installation of this
product.
4. Before drilling ensure that the area is clear of fuel, electrical & other components.
5. All holes drilled into the body panels shall have all burrs & swarf removed then coated with a suitable rust
preventative paint.
6. The high tensile fasteners supplied with this product were used to achieve the specified rating. If replacement is
required ensure that fasteners of the same rating & quality are used. Contact an authorised Hayman Reese
dealer if further information is required.
7. Ensure that all hardware is fastened to torque list below check fasteners on regular basis.
8. Towbar load rating sticker provided with this product shall be conspicuously located on inside rear end of the
driver's door. (See diagram below).
9. Hayman Reese recommends that you check your tow ball to ensure that it complies with the Australian
standards AS 4177.2.
10. PLEASE NOTE: It is advised to remove your LUG or TBM when not actually towing so as to produce a clear
view of the vehicles registration plate if obscured, and to also provide maximum available departure angle.
11. Pull Pin must be fit in down position.
Tow bar Maintenance and Care.
Hayman Reese recommends that bolt torque’s, as listed below, are routinely and regularly inspected and checked for
correct tension. Replace any worn or defective parts.
We recommended to remove Tow Ball Mounts (TBM’s, tongues or lugs) when not being used for any considerable length
of time.
So as to avoid injury, when not towing it is suggested that the tongue, Pull Pin and R-clip are removed then stored in a
safe, clean and dry place, away from excessive moisture.
Hitch Pull Pins and spring “R” clips are regularly checked for proper installation. Replace any worn or defective parts.
FOR TOWING PURPOSES ONLY
For towing capacity details please refer to vehicle
owner’s manual or to the manufacturer. Overloading can
void your warranties.
RECOMMENDED ASSEMBLY TORQUE
LISTING
Diameter Grade 8.8 Bolt
M6 9.5 Nm
M8 21.7 Nm
M10 43.4 Nm
M12 77.3 Nm
M14 146 Nm
M16 189.8 Nm
Place load rating sticker
inside driver’s door here

HAYMAN REESE
PART No: 03267RW
MITSUBISHI TRITON MQ MY19 UTE
INSTALLATION INSTRUCTIONS
PLEASE ENSURE THAT ALL INSTRUCTIONS ARE UNDERSTOOD PRIOR TO FITMENT
PLACE THESE INSTRUCTIONS IN THE VEHICLES’S GLOVEBOX AFTER INSTALLATION IS COMPLETED
Rev: A Page 3 Issue Date: 25-01-2019
ITEM
DESCRIPTION
QTY
1
TRITON WITH STEP WELDED ASSY
1
2
CLASS 4 TBM
1
3
WASHER PLAIN 1/2X1-1/8X16G
20
4
M12x1.75 HEX NUT PC8
10
5
SET SCREW M12-1.75x40 GR10.9
10
6
UNIVERSAL PLUG BRACKET KIT
1
7
TOWBALL 50MM FLAT CHROME 3500KG HR
1
8
"D" SHACKLE 10mm
2
9
SMART PIN ASSY CLASS 4 –GOLD
1
10
HAYMAN REESE LOGO STICKER
1
11
HITCH BOX COLLAR COVER
1
12
WIRING LOOM
1
13
ACRYLIC COMPLIANCE LABEL
1
14
M4 WASHER
2
15
SCREW PAN HD M4 X 16 X 0.7P G4.6
2
16
NUT NYLON LOCK HEX HD M4X0.7P G8
2

HAYMAN REESE
PART No: 03267RW
MITSUBISHI TRITON MQ MY19 UTE
INSTALLATION INSTRUCTIONS
PLEASE ENSURE THAT ALL INSTRUCTIONS ARE UNDERSTOOD PRIOR TO FITMENT
PLACE THESE INSTRUCTIONS IN THE VEHICLES’S GLOVEBOX AFTER INSTALLATION IS COMPLETED
Rev: A Page 4 Issue Date: 25-01-2019
1. Remove step from vehicle secured with 2
bolts per side, making sure to disconnect
reversing sensors if fitted.
2. Remove LH Step bracket from vehicle
secured with 2 x bolts complete with 2 x
washers and 1 x nut per bolt and discard.
Repeat for other side.
3. Lift towbar to vehicle and secure with 5 x
Bolts complete with 2 x washers and 1 x nut
per bolt on both the LH & RH side.
Torque all fasteners to 125Nm.

HAYMAN REESE
PART No: 03267RW
MITSUBISHI TRITON MQ MY19 UTE
INSTALLATION INSTRUCTIONS
PLEASE ENSURE THAT ALL INSTRUCTIONS ARE UNDERSTOOD PRIOR TO FITMENT
PLACE THESE INSTRUCTIONS IN THE VEHICLES’S GLOVEBOX AFTER INSTALLATION IS COMPLETED
Rev: A Page 5 Issue Date: 25-01-2019
4. Refit the step to vehicle, using the existing
fasteners, to the towbar sidearms.
Torque the fasteners to 50Nm.