Hayward E-command® 4 User manual

ECOMMAND 4 Programming Flow Chart Hayward

ECOMMAND 4

Automation

Installation Manual

HPC-4

HPC-4-ACT

HPC-4-RC

HPC-4-ACT-RC

www.haywardnet.com

092419A

620 Division St.

Elizabeth, NJ 07207

denotes conditional items

12 hour or 24 hour time format

ºF or ºC

reset to default

default menu

day and time

water temperature

air temperature

chlorinator setting

salt level

reason pump is running (not scheduled)

reason hi-speed is running (not scheduled)

countdown time remaining

heater control status

system manual off

check system error

filter speed

settings menu

spa heater1 temperature

pool heater1 temperature

spa solar temperature

pool solar temperature

superchlorinate

spa chlorinator setting

pool chlorinator setting

spa high/low speed

pool high/lowspeed

day and time

backlit display light

beeper

teach wireless remote

wireless channel

timers menu

pool filter pump1 or hi-speed

pool filter pump2 or lo-speed

spa

lights

aux1

aux2

valve3

superchlorinate

diagnostic menu

salt level

water sensor

air sensor

solar sensor

mainsoftware revision

displaysoftware revision

filter bridge/vsc software revision

RF base software revision

configuration menu

chlorinator

pool/spa

filter

heater1

solar

lights

aux1

aux2

valve3

7-day or weekend/weekday timeclock

formodels

LIMITEDWARRANTY(effective01/01/09)Goldlinewarrants itsAquaRite,Aqua RitePro,AquaLogic, ProLogic and

E-Command products to be free of defects in materials and workmanship, under normal use and service for a period of

three (3) years. This warranty is applicable from the initial date of installation on private residential swimming pools in

the US and Canada. The warranty is not transferable and applies to the original owner only.

Aqua Trol, commercial installations, installations outside of the US and Canada, accessory products and replacement

parts are covered under the terms of the warranty for a period of one (1) year.

Proof of purchase is required for warranty service. If written proof of purchase is not provided, the manufacturing date

code will be the sole determinant of the date of installation of the product.

To obtain warranty service or repair, please contact the place of purchase or the nearest Goldline authorized warranty

service center. For more information on authorized service centers please contact the Hayward/Goldline Technical

Service Support Center ( 61 Whitecap Road, North Kingstown RI, 02852) or visit the Goldline web site,

www.goldlinecontrols.com.

WARRANTYEXCLUSIONS:

1. Material supplied or workmanship performed by others in process of installation.

2. Damage resulting from improper installation including installation on pools larger than the product rating.

3. Problemsresulting from failure to install, operate or maintain the product(s) inaccordance with therecommendations

contained in the owners manual(s).

4. Problems resulting from failure to maintain pool water chemistry in accordance with the recommendations in the

owners manual(s).

5. Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alternations, fire, flood,

lightning, freezing, external water, degradation of natural stone used in or immediately adjacent to a pool or spa, war

or acts of God.

DISCLAIMER. THE EXPRESS LIMITED WARRANTY ABOVE CONSTITUTES THE ENTIRE WARRANTY OF

GOLDLINEWITH RESPECTTOITSPOOLAUTOMATIONAND CHLORINATION PRODUCTSAND IS IN LIEU OF

ALLOTHERWARRANTIES, EXPRESSED OR IMPLIED, INCLUDINGWARRANTIESOFMERCHANTABILITYOR

FITNESS FORAPARTICULAR PURPOSE. THIS WARRANTYGIVESYOU SPECIFIC LEGALRIGHTS,ANDYOU

MAYALSO HAVEOTHER RIGHTSWHICH VARYFROM STATE TOSTATE. IN NO EVENTSHALLGOLDLINEBE

RESPONSIBLE FOR ANY CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES OF ANY NATURE

WHATSOEVER,INCLUDING, BUTNOTLIMITEDTO,PERSONALINJURY,PROPERTYDAMAGE,DAMAGETOOR

LOSS OF EQUIPMENT, LOST PROFITS OR REVENUE, COSTS OF RENTING REPLACEMENTS, AND OTHER

ADDITIONALEXPENSES, EVENIFTHESELLERHADBEENADVISEDOFTHEPOSSIBILITYOFSUCHDAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THEABOVE LIMITATION OR EXCLUSION MAYNOTAPPLYTOYOU.

NO WHOLESALER, AGENT, DEALER, CONTRACTOR OR OTHER PERSON IS AUTHORIZED TO GIVE ANY

WARRANTYON BEHALFOFGOLDLINE.

THISWARRANTYISVOIDIFTHE PRODUCT HAS BEENALTERED INANYWAYAFTER LEAVINGTHEFACTORY.

IMPORTANTSAFETYINSTRUCTIONS

Whenusing this electricalequipment, basicsafetyprecautions shouldalwaysbe

followed,includingthefollowing:

•READ AND FOLLOW ALL INSTRUCTIONS

•

WARNING: DisconnectallAC powerduringinstallation.

•

WARNING: Water in excess of 100 degrees Fahrenheit may be

hazardousto your health.

•

WARNING: Toreduce the risk ofinjury, donotpermit children to

usethis product unless theyareclosely supervised atalltimes.

•Agreencolored terminalmarked“EarthGround”islocatedinsidethewiring

compartment. To reduce the risk of electric shock, this terminal must be

connected to the grounding means provided in the electric supply service

panelwithacontinuouscopperwireequivalentinsizetothecircuitconductors

supplyingtheequipment.

•A wireconnector isprovided onthisunittoconnectaminimum8AWG(8.4

mm2)solidcopperconductorbetweenthisunitandanymetalequipment,

metalenclosuresofelectricalequipment,metalwaterpipe,orconduitwithin

5feet(1.5m)ofthe unit,toconnect theequipmentassemblyorspa toa

circuitprotectedbyaground-fault circuit-interrupter.

•OnebondinglugforUSmodels(twoforCanadianmodels)isprovidedonthe

external surface. To reduce the risk of electric shock, connect the local

common bonding grid in the area of the swimming pool, spa, or hot tub to

theseterminalswithaninsulatedorbarecopperconductornotsmallerthan8

AWG US/6AWGCanada.

•All field installed metal components such as rails, ladders, drains, or other

similarhardwarewithin3metersofthepool,spaorhottubshallbebondedto

theequipmentgroundingbuswithcopperconductorsnotsmallerthan8AWG

US/6AWG Canada.

•SAVE THESE INSTRUCTIONS

Table of Contents

Introduction BeforeYouBegin................................................................... 1

InstallationSteps.................................................................... 1

1. Mounting ECOMMAND4ControlCenter............................................ 2

Equipment TemperatureSensors............................................................ 2

OptionalWirelessRemoteControl...................................... 2

OptionalBaseStation............................................................ 3

OptionalValveActuators........................................................ 3

2. Plumbing PlumbingConfiguration.......................................................... 4

3. Electrical MainService........................................................................... 5

Wiring GroundingandBonding........................................................ 5

CircuitBreakerInstallationandWiring................................ 6

GeneralPurposeOutlet......................................................... 6

ECOMMAND4ControlPower.............................................. 6

HighVoltagePoolEquipment............................................... 7

LowVoltageWiring................................................................ 8

4. Configuration ConfigurationMenu............................................................... 14

5. System Startup BeforeStartup........................................................................24

and Checkout HeaterCheckout....................................................................24

ServiceMode.........................................................................25

6. Warranty ECOMMAND4LimitedWarranty........................................28

Introduction

Before You Begin

What’sIncluded

Beforeattemptingto installtheECOMMAND4system, checkthatthefollowingcomponentshavebeen

includedinthepackage:

ECOMMAND 4 Electronics Unit

(3) Temperature sensors with 15 ft. (5m)cable,hoseclamp

(2) Goldline GVA-24 actuators (HPC-4-ACT, HPC-4-ACT-RC only)

(1) GoldlineAQL2-BASE-RF/AQL2-SS-RF remote control (HPC-4-RC,HPC-4-ACT-RConly)

What’sNOT Included

Someofthe additionalitemsthatyoumayneedtocomplete aninstallationinclude:

Circuit breakers

Noneare included with control—seepage6 and insideofdoor for suitable breakers

Wire

4-conductorcable(electronics unittoexternalchlorination)

Wire/conduit for100Aservicefrommain panelto ECOMMAND 4

Wire/conduitforfilterpumpandotherhighvoltageloads

Wireforbonding

Miscellaneous

Mountinghardware (screws,etc.) formountingECOMMAND 4

Valves(usestandard Hayward,Pentair/Compool, orJandyvalves)

Additionalvalveactuators

AccessoryProducts-OrderSeparately

AQL2-SS-RF Wireless Spa Side Remote Control (Included with HPC-4-RC, HPC-4-ACT-RC)

AQL2-BASE-RF Base Station required if usingAQL2-SS-RF (Included with HPC-4-RC, HPC-4-ACT-RC)

AQL-DIM LightDimmerRelay

GVA-24 ValveActuator

V&A-xx Valve &Actuator (xx=1P(1.5” pos. seal), -2P (2” pos. seal), (Included with HPC-4-ACT,

HPC-4-ACT-RC)

HighVoltagepoolequipment

Lowvoltagewiring (temperaturesen-

sors,heater, etc.)

4. ECOMMAND4configuration (page 14)

5. System Startup and checkout (page 24)

Installation Steps

Detailson each installation steparepresented on

thefollowingpages:

1. Mountingthe equipment(page 2)

ECOMMAND4mainunit

Temperaturesensors

OptionalRemoteControl

OptionalBaseStation

Valveactuators(ifapplicable)

2. Plumbing (page4)

GeneralPoolEquipment

3. ElectricalWiring (page6)

Mainservice

Groundingandbonding

Circuitbreakers

ECOMMAND4controlpower 26

1. Mounting the Equipment

ECOMMAND 4 Control Center

The ECOMMAND 4 is contained in a raintight enclosure that is suitable for outdoor mounting. The

controlmustbemounted aminimum of5 ft.(2 meters)horizontal distancefromthepool/spa(ormore,if

localcodes require).The ControlCenter isdesignedtomountvertically ona flatsurfacewiththeknock-

outsfacingdownward. Becausetheenclosurealsoactsasaheatsink(disperses heatfrominside thebox),

itisimportantnottoblockthe foursides ofthe control. DonotmounttheECOMMAND4inside apanel

ortightlyenclosedarea.

Whenselectingalocation, notethat thestandard cablessupplied withthe temperaturesensors, andvalve

actuators(if applicable)areall 15ft.(5m) long.

Temperature Sensors

Threesensors areincluded withtheECOMMAND 4. Awatersensorand anair sensormustbe installed

atall timesforproper operation. Asolar sensorisrequired ifthesolar functionisenabled.

Water Sensor

Thissensoris usedtomeasurethepool/spa temperatureandis installedinthefiltrationplumbing afterthe

filterbutbeforeeitherthesolarorconventionallyfueledheaters—refertotheplumbingoverviewdiagram.

1. Drill a3/8” (10mm)diameterholeinthe PVCpiping andremove allchips andburrs.

2. Insertsensoruntil O-ringcollarsitsflushon thehole.

3. Position hoseclamp over thesensor andgentlytighten untilO-ringmakes anadequate seal. Do not

overtighten.

4. For maximumtemperatureaccuracy,coverthe sensorand3” (6cm)ofpipe oneitherside with

insulationandwhitepaint.

AirSensor

Mount the air sensor outdoors.

IMPORTANT: Mount the air sensoroutofdirectsunlight.

SolarSensor

For solar applications, mount the sensor near the solar collector array so that it is exposed to the same

sunlightas thecollectors. Use additionalcable(20AWG)if necessary.

OptionalAQL2-SS-RF Remote Control (included with HPC-4-RC, HPC-4-

ACT-RC)

TheECOMMAND4iscompatiblewithAQL2-SS-RFwirelessremotecontrolonly. TheAQL2-SS-RF

isa waterproof portable remotecontrolthat is designedtobe used in andaroundthe pool/spa area. The

AQL2-SS-RFfloats andcan beleft inthewaterforeasy access. AsingleAQL2-BASE-RF BaseStation

must be installed on the ECOMMAND 4 in order to use this remote control. The maximum distance

betweenthewirelessremote and the base station on the ECOMMAND 4 main control unit is 400 feet

(120m)lineofsightor200feet(60m) through walls, etc. If in doubt about the distance, test operation

beforeinstallingtheremote.Allwirelessmodelsrequiretheusertorunthe“TeachWireless”routineinthe

SettingsMenu. This informationcan befoundintheECOMMAND 4Operation Manual.

225

3.Once theheater isrunning, youcan verifythe “heatercooldown”feature(optional-seeConfiguration

Menu/HeaterConfig.)isoperatingproperly:

• Press the “Filter” button once (for 2 speed pumps, this may require 2 pushes of the “Filter”

button).

• Theheatershouldturn off(“Heater” LEDoff) andthe “Filter”LED willflash toindicated heater

cooldownisactive.

• Thedisplaywillperiodicallyindicatethatthefilterpumpisonforheatercooldownandshowthe

minutesremaining.

• Thepumpwillautomaticallyturnoffattheend ofthe 5minute heatercooldown period.

For more detailed instructions on control and operation of the ECOMMAND 4 system, refer to the

OperationManual.

ServiceMode

Servicemodedisablesall automaticcontrol operationand isintended tobe usedwhen servicingthe pool

system. Toenterservicemode,pushtheSERVICEbuttononceonthemainunitkeypad. Thiswillinitially

turnalloutputsoffandthenallowyoutoturnoutputson/offmanuallyatthemaindisplay(only). In service

mode,thebuttonson the optional spa side remote will turn outputs off,butwillnotturn any output on.

Heatercontrol outputs and solarcontroloutputs are prevented fromturningon if thewatertemperature

exceeds 104ºF (40ºC).

Pushing the SERVICE button again will enter a timed service mode. Service operation as described

abovewillcontinue for3hours,thenautomatically returntonormaloperation.

Pushthe SERVICE button once moretoexit out of Servicemode.

Optional Base Station (included with HPC-4-RC, HPC-4-ACT-RC)

TheAQL2-BASE-RF optional base stationmustbe installed if theAQL2-SS-RF is used.To install the

basestation, removetheknockout onthe upperleftside ofthe ECOMMAND4main controlunit,insert

thebasestation, and then tighten the nut from theinside. Alsoreferto the Base Stationmanual andthe

diagramon page 13.

Optional Valve Actuators (included with HPC-4-ACT, HPC-4-ACT-RC)

Foroptionalactuators used with the ECOMMAND 4—note that the internalcamsintheactuator may

alsohave tobe adjusteddepending onthe waytheactuatorismountedonthe valveand thedesired valve

action.

RETURN SUCTION

OUT

(Common)

OUT

OUT IN

5. System Startup and Checkout

Before Startup

BeforestartingtheECOMMAND 4 for the first time, be sure that the following items have beencom-

pleted:

1. Properly ratedcircuitbreakers are installedinthe ECOMMAND 4subpanel.

2. All wiringisperformed accordingto NECandlocal codes.

3. The ECOMMAND 4 isproperlygroundedandbonded.

4. The ECOMMAND4isproperlyconfigured tocontrol alldesiredfunctions.

ProgramAutomatic Operation

Refertotheprogrammingflowchartonthebackcoverofthis manualfor alisting ofthe availablemenus

andtheitems includedineach menu.

SettingsMenu

Heaterand/or solarthermostat settings

Chlorinatorsettings(ifapplicable)

DayandTime

TimersMenu

Timeclockand/orCountdowntimersettings

Heater Checkout

Followtheseinstructionsto verifythat theECOMMAND 4is properlycontrolling theheater.

1. Check that theECOMMAND4 is calling for theheaterto turn on as indicatedbythe “Heater” LED

beingilluminated.Ifthe“Heater”LEDisilluminated,godirectlytostep2;ifnot,thencheckthefollow-

ing:

• Theheateris enabled(ConfigurationMenu/Heater Config.).

• Theheater temperaturesetting isat least2ºFgreater thanthe watertemperature (SettingsMenu/

Pool Heater & Spa Heater).

• Thefilterpumpisrunning.

• If the pool has solar heat and the solar priority feature is enabled (Configuration Menu/Solar

Config)thensolarmustbe offinorderfortheheaterto fire.Theeasiestwaytoforcesolar offisto

goto theSettings Menu/Pool Solar& SpaSolarand temporarilylower thetemperaturesettings

belowthe currentwatertemperature.

2.Check thattheheater isrunning.If not,thencheck:

• Poweris supplied to theheater.

• The ECOMMAND 4 control output is properly connected to the heater control (see ”Heater

Control”wiring,page 8).

• Some heaters also have internal switches or jumpers that have to be set correctly for remote

controloperation—refer to theheater manual andalso “Heater Control”(page8).

• Heateristurnedon(“KillSwitch”is inthe “ON”position).

• Ifa heaterbypass valveis installed,checkthatwaterisflowingthrough theheater.

• The heater temperature setting is set as high as possible (usually 104ºF/40ºC). Also note that

someheat pumps actuallyhave be settothe lowestpossibletemperature.

2. Plumbing

Pool/Spa system configuration

Thesesystemsuseasinglefilterpump andfilter. Poolorspaoperationiscontrolledbytwo3-wayvalves

(suctionand return). Refertothe diagrambelow.

Someimportant notes regardingthe ECOMMAND 4controlof StandardPool/Spasystems:

In Pool/Spa Config., select:

Pool/Spa Setup

Pool and Spa

1. The ECOMMAND 4canbe programmed to accommodatespaspillover,if desired.

2. A conventionalheater(gasorheat pump)and solarcanbeusedto heatboth thepoolandthespa.

3. If thechlorinator cellis plumbedpriortothepool/spareturnvalve,thenboththepoolandthe spa

canbechlorinated(onlywhenoptional externalchlorinationis used).

4. Thewatersensor shouldbeinstalledpriortoanyheater orsolar andwilldisplayeitherthepoolor

thespatemperature,dependingonthecurrentoperationofthepool. Thetemperature willonlybe

displayedwhenthefilterpumpisrunning.

5. Ifanywaterfeatureorpressuresidecleanerboostpumpsareused,besuretoenablethe“interlock”

feature(see“Configuration Menu” for details) to ensure that the pumpsoperateonlywhenthe

filterpumpisonandthesystem isin the“pool only”operating mode.

6. The plumbingdiagramabove is intendedto be usedasa generalguidelineand isnota complete

plumbingschematicforthepool.

7. Theairsensormustbeinstalledifthefreezeprotectionfeatureisenabledforthefilter,valvesoraux

outputsorifthechlorinatorisenabled.

Valve3 Pump Speed

This is the speed of the pump when the Valve3 output is on. The choices are the Settings

Menu speed and a speed that is unique to the Valve3 output only. The default selection is

“Settings Menu”. This is the speed of the pump that has been selected in the Settings Menu

for normal filter operation. If an alternate speed is desired when the Valve3 output is on, push

“+” or “-” and select from “Lowest” to “Highest” in 5% increments.

All Timeclocks

7-day

Move to previous/next configuration menu

Toggle between 7-day (default) and Weekend/Weekday time options

This selection affects ALL of the timeclock logic in the ECOMMAND 4. If “7-day” is

selected, each timeclock will have one set of turn-on/turn-off settings that operate every day

of the week. If “Weekend/Weekdays” option is selected then the user can enter one set of

turn-on/turn-off times for the weekend (fixed as Saturday/Sunday) and another set of turn-

on/turn-off times for weekdays (Monday through Friday).

Time Format

12 hour AM/PM

Units

ºF and PPM

Move to previous/next configuration menu

Toggle between 12 hourAM/PM (default) and 24 hour time format options

Toggle between ºF and PPM (default) and ºC and g/L (Metric) options

Reset Config. to

Default Press +

Are you sure?

+ to proceed

Config. reset

Confirmed

Initiate reset of all configuration parameters

Reset all configuration parameters

Move to previous/next configuration

menu (config. not reset)

Move to previous/next menu (config. not reset)

Move to previous/next configuration menu

Use this function to erase all previous system configuration and reset all configuration

parameters back to the factory default values. This function is NOT reversible--be careful.

FILTER

SOLAR BOOST

PUMP

SOLAR

VALVE

HEATER

BYPASS

VALVE

(manual)

CELL FLOW

SWITCH

CHECK

VALVE

POOL SWEEP

BOOST PUMP

WATER

FEATURE

PUMP

POOL/SPA

RETURN

VALVE

WATER

FEATURE

VALVE

SPA

SPA JET

PUMP

SPA

BLOWER

POOL/SPA SUCTION

VALVE

CHECK VALVE

POOL VACUUM

VALVE

MANUAL

VALVE

MANUAL

VALVE

MANUAL

VALVE

ENERGY

FILTER

TWO-WAY

VALVE

SKIM

POP-UP

SPILLOVER

POP-UP

OVERFLOW

POP-UP

RETURN

JET

IN-FLOOR

CLEANER

VALVE

WATER

FEATURE

PUMP

WATER

FEATURE

POP-UP

MAIN

DRAIN ENERGY

SAVER

PRESSURE

CLEANER

NON-BOOST

PRESSURE

CLEANER PRESSURE

CLEANER

SUCTION

CLEANER

SOLAR

TEMPERATURE

SENSOR

POOL

FILTER

PUMP

High Voltage Relays

Valve Outputs

Filter Pump

Lights

Aux 1

Aux 2

Pool/Spa Suction

Pool/Spa Return

Valve 3

TRANSFORMER

HIGH VOLTAGE

LIGHTS

LOW VOLTAGE

LIGHTS

FIBER OPTIC

LIGHT SOURCE COLOR WHEEL

ISOLATED

WATER

FEATURE

PUMP

POOL/SPA

TEMPERATURE

SENSOR

CHECK

VALVE

(prevents draining

of raised spas)

CHECK

ALVE

(prevents draining

of raised spas)

if optional Aqua Rite or

Swimpure external chlorination

control is used

3. Electrical Wiring

The ECOMMAND 4 Control Center requires both high and low voltage connections. Low voltage

connectionswillbe made to actuators, sensors, remote keypad, etc. High voltage connections will be

madeto pumps,lights,etc., as wellas providing directinput power totheControl Center. Always:

-Ensurethat Poweris disconnectedprior todoingany wiring

-Followall local andNEC(CEC if applicable)codes

-Usecopperconductors only

Main Service (Power to the Circuit Breaker Subpanel)

TheECOMMAND 4circuitbreaker subpanelisrated for100Aservice. Run properlyrated conductors

(L1,L2,N,andground) from the primary house electrical panel to the main power connections on the

ECOMMAND4circuit breaker base. The connection at the main housepanelshouldbe to a 240VAC

circuitbreakerratedat100Amaximum.

Grounding and Bonding

Connectagroundwirefromtheprimaryelectricalpanel to the ECOMMAND 4 ground bus bar. Also

groundeach pieceof highvoltage (120or240VAC)equipmentthatisconnected tothe ECOMMAND4

controlrelays or circuit breakers. The ECOMMAND 4 should also be connected to the pool bonding

system by an 8AWG (6AWG for Canada) wire. Alug for bonding (2 for Canada) is provided on the

outside/bottomof the ECOMMAND4enclosure.

High Voltage

Relays

Display/Keypad

Control Power

Input

Subpanel

Valve Connector

Sensor

External Chlorinator

(requires Aqua Rite)

Input

Wireless Base

Receiver Connector

Heater Output

Valve3 Pump Spd

Settings Menu

Select between Settings Menu (default) and the desired pump speed

only if filter pump is set to variable

and relay type is set to standard

Move to previous/next configuration menu

Valve3 Freeze

Disabled

Toggle between Enabled and Disabled (default) Valve3 Freeze

Move to previous/next configuration menu

for all functions except super chlorinate

Valve3 Config.

+ to view/change

Valve3 Function

Solar

Push to access Valve3 options

Rotates between k

Timecloc (default), Solar, In-floor Cleaner,

Filter, Lights, Aux1 and Aux2

Move to previous/next configuration menu

Move to next menu item

Valve3 Interlock

Disabled

Toggle between Enabled and Disabled (default) Valve3 Interlock

Move to next menu item

for all functions except solar and super chlorinate

Valve3 Function

Timeclock (default) – the valve turns on/off at the times set for the valve3 timeclock in the

Timers Menu (see Operations Manual).

Solar – the valve operates when the filter pump is running and solar heat is available and the

water is less than the desired temperature setting. Solar heating must be enabled in the

“Solar Config. menu for proper operation to occur.

In-Floor Cleaner – the valve switches the water returning to the pool between the in-floor

cleaner and the normal return jets which facilitate efficient surface skimming. The valve will

operate the in-floor cleaner for the first half of each clock hour and then switch to the jets/

skimming for the last half of the hour.

Valve3=Filter – the valve operates whenever the Filter relay is on.

Valve3=Lights – the valve operates whenever the Lights relay is on.

Valve3=Aux1 – the valve operates whenever the Aux1 relay is on.

Valve3=Aux2 – the valve operates whenever the Aux2 relay is on.

Valve3 Interlock

If “Enabled”, this feature will override the function (timeclock or in-floor cleaner) selected

above and turn the valve off when: the filter pump is off, first 3 minutes of filter pump

operation (allows the pump to prime and get water flowing), or for the first 3 minutes after

solar turns on (allows air in the solar panels to be purged). Interlock is not available for solar

or super chlorinate.

Valve3 Freeze Protection

This function protects the pool and plumbed equipment against freeze damage. If Freeze

Protection is enabled and the AIR temperature falls sensor falls below the selected freeze

temperature threshold, the ECOMMAND 4 will turn on the valve to allow circulation of the

water. IMPORTANT: this only enables operation of the valve3 output during freeze--see the

“Filter Pump Config.” menu to enable freeze protection for the main circulation system.

Circuit Breaker Installation and Wiring

Circuitbreakersaretobesuppliedbytheinstaller. Refer to the circuit breaker chart below for a list of

suitablecircuit breakers thatcan be used. Followthecode and thecircuit breaker manufacturer’srating

requirementsregardingthesizeandtemperatureratingforwiring. Notethatsomepoolequipmentmaybe

requiredtobe connected to ground faultcircuitbreakers—checklocal and NEC (CEC) codes.

General Purpose Outlet

If desired, a duplex receptacle with weatherproof cover (supplied by installer) may be installed in the

knockoutson the lower rightside of the ECOMMAND4enclosure. Per code, thereceptacleshould be

aGFCItype. Alternatively, connectastandardreceptacleto a GFCB.

ECOMMAND 4 Control Power

The ECOMMAND 4 requires 120VAC, 2A power to operate the control logic circuits. This power

should be connected to a circuit breaker rated at 125% of the intended load or the next higher size

available.

Aux1 Function

Manual On/Off (default)—the aux relay will alternate between turning on and off when the

aux button is pressed. There is no automatic control logic.

Countdown Timer – the aux relay will turn on when theAUX button is pressed and then will

turn off automatically after a programmed time (see Timers Menu, Operation Manual). The

AUX button can also be used to turn the output off.

LowSpeed of a2-speed FilterPump– the ECOMMAND4 willoperate theaux relay whenever

the low speed operation of the filter pump is required. It is very important that the “2-speed”

filter pump option be selected under the “Filter Config.” Menu for proper operation.

Timeclock – the aux relay will turn-on and turn-off at the times set for the aux1 timeclock in

the Timers Menu. The AUX button can also be used to turn the output on and off.

Solar – the aux relay operates a solar booster pump which will turn on when the filter pump

is running and solar heat is available and the water is less than the desired temperature

setting. It is important to note that “Solar Control” must be enabled in the “Solar Config.”

menu for proper operation to occur.

Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super

Chlorinate cycle when theAux button is pressed, rather than using the Settings Menu. Note

that only one button can be assigned to this function.

Aux1 Relay

This feature allows the user to select either “Standard” (default) or “Dimmer” type relay for

theAux1 output. The optionalAQL-DIMdimmer kitmust beinstalled if“Dimmer” isdesired.

When “Dimmer” is selected, and the Aux1 output is manually turned on, the “+” and “-”

buttons adjust the level from 20% to 100% (default). The level is saved for the next time the

aux1 output is turned from off to on.

Aux1 Interlock

If “Enabled”, this feature will override the function (Manual On/Off, Countdown Timer,

Timeclock), selected above and turn the aux1 off when: filter pump is off, first 3 minutes of

filter pump operation (allows the pump to prime and get water flowing), when the pool/spa

suction return valves are in any position other than “pool only”, or for the first 3 minutes

after solar turns on (allows air in the solar panels to be purged). Interlock is not available for

solar, low speed filter pump, super chlorinate or dimmer.

Aux1 Freeze Protection

This function protects the pool, plumbing, and equipment against freeze damage. If Freeze

Protection is enabled and the AIR temperature sensor falls below the selected freeze

temperature threshold, the ECOMMAND 4 will turn on the aux relay to circulate the water.

IMPORTANT: this only enables operation of theAUX output during freeze--see the “Filter

Pump Config.” menu to enable freeze protection for the main circulation system.

Aux1 Pump Speed

This is the speed of the pump when the Aux1 output is on. The choices are the Settings

Menu speed and a speed that is unique to the Aux1 output only. The default selection is

“Settings Menu”. This is the speed of the pump that has been selected in the Settings Menu

for normal filter operation. If an alternate speed is desired when theAux1 output is on, push

“+” or “-” and select from “Lowest” to “Highest” in 5% increments.

Siemens

Murray

Manufacturer

Single Double Quad

Twin GFCB

Filler Plates

QP QP QT QT QPF QF3

SUITABLE LISTED BREAKERS Tightening

Torque

MP-T MP-T MH-T MH-T MP-GT LX100FP

25lb-in

Factory

Prewired

Field

Wired

120, 2VA

High Voltage (120/240V) Pool Equipment

AllECOMMAND 4relays aredouble pole(they make/breakboth“legs”of240V circuits)and arerated

at3HP/30A at 240V (1½HP/30A at120V). Referto the diagram belowfortypicalrelay wiring.

WARNING: Do not use the ECOMMAND 4 to control an automatic pool cover.

Swimmers may become entrapped underneath the cover.

Twospeedfilterpump: Requires 2relays (FILTERplusoneoftheAUXrelays) forproper operationof

both speeds.

IMPORTANT: Be suretofollowthewiringdiagram belowANDto configure

thecontrollogicaccordingto the instructions on page 14.

Lights: Agroundfaultcircuit breaker mustbeused to supplypower for highvoltagepool/spa lighting.

Lowvoltagelights willrequireanexternaltransformer. Forlightingsystemsthathavebothalight source

andcolor wheel,connect thelight sourceto the“Lights”relayandthen connectthe colorwheel toone of

theAUX outputs.

240 VAC

Load 120 VAC

Load

Wiring relays for 240 VAC

Pool Equipment Wiring relays for 120 VAC

Pool Equipment

120 VAC

Load

Wiring GFCB for 120 VAC

Pool Equipment

2-Speed

Filter

Pump

Lo Speed

Hi Speed

Common

Ground

Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super

Chlorinate cycle when the Lights button is pressed, rather than using the Settings Menu.

Note that only one button can be assigned to this function.

Lights Relay

This feature allows the user to select either “Standard” (default) or “Dimmer” type relay for

the Lights output. The optional AQL-DIM dimmer kit must be installed if “Dimmer” is

desired. When “Dimmer” is selected, and the Lights output is manually turned on, the “+”

and “-” buttons adjust the level from 20% to 100% (default). The level is saved for the next

time the lights are turned from off to on.

Lights Interlock

If enabled, this feature will override the function (Manual On/Off, Countdown Timer,

Timeclock) selected above and turn the lights relay off when: filter pump is off, first 3

minutes of filter pump operation (allows the pump to prime and get water flowing), when the

pool/spa suction return valves are in any position other than “pool only”, or for the first 3

minutes after solar turns on (allows air in the solar panels to be purged). Interlock is not

available for solar, low speed filter pump, super chlorinate or dimmer.

Lights Freeze Protection

This function helps protect equipment that is wired to the lights relay against freeze damage.

IfFreeze Protection is enabled and theAIR temperature sensor falls below the selected freeze

temperaturethreshold, the ECOMMAND4 will energizethe lights relay. IMPORTANT: this

only enables operation of the lights relay during freeze--see the “Filter Pump Config.” menu

to enable freeze protection for the main circulation system.

Lights Pump Speed

This is the speed of the pump when the Lights output is on. The choices are the Settings

Menu speed and a speed that is unique to the Lights output only. The default selection is

“Settings Menu”. This is the speed of the pump that has been selected in the Settings Menu

for normal filter operation. If an alternate speed is desired when the Lights output is on, push

“+” or “-” and select from “Lowest” to “Highest” in 5% increments.

NOTE: The configuration parameters for the Aux2 output are the same as shown below for Aux1.

Aux1 Pump Spd

Settings Menu

Select between Settings Menu (default) and the desired pump speed

only if filter pump is set to variable

and relay type is set to standard

Move to previous/next configuration menu

Aux1 Config.

+ to view/change

Aux1 Function

Manual On/Off

Aux1 Relay

Standard

Push to access Aux options

Toggle between Standard (default) and Dimmer

Move to previous/next configurationmenu

Move to next menu item or previous/next configuration menu

Aux1 Interlock

Disable

Aux1 Freeze

Disable

Toggle between Enabled and Disabled (default) Aux1 Interlock

Toggle between Enabled and Disabled Aux1 Freeze(default)

Move to next menu item

Move to previous/next configuration menu

for manual on/off, countdown

timer and timeclock functions

Move to next menu item

Rotates between

Manual On/Off (default), Countdown Timer,

Low Speed- Filter, Timeclock, Solar, and Super Chlorinate

for all functions except dimmer relay, solar

super chlorinate, and low speed

or all functions except dimmer relay,

WARNING: Do not use the ECOMMAND 4 to control an automatic pool cover.

Swimmers may become entrapped underneath the cover.

HaywardVariableSpeedFilterPump: Proper installation of the Hayward TriStar Variable Speed

Control(VSC)includeshighvoltageinputwiring,communicationwiring,andmenuconfiguration/settings.

Referto the followingdiagramfor proper input wiringto theVSC.Wiringfrom the 220Vbreaker must

connectthrough theECOMMAND4’s Filter relay. TheFilter relayis used tosupply input powertothe

VSCpump control. Therelay willbeon whenthe filterpump outputison. When thefilter pumpoutput

is off, the relay will be off. Note that when the filter pump relay is off (power off to the VSC), the

ECOMMAND4will notdisplay errorsordiagnosticsforthe pump. Thefilterpumprelaymust beon for

diagnosticfunction.

220 VAC input

power to VSC

Low Voltage Wiring

ValveActuators

The ECOMMAND 4 can control up to three automatic valve actuators. Two of the valve outputs are

dedicatedto thepool/spasuction (Valve2)and return (Valve1)valves. Valve3 isforgeneral purposeuse

(solar, waterfeature, in-floorcleaner, etc.).

Forinstallations with solarheating,Goldline offerstheAQ-SOL-KIT-xxsolar kit thatcontainsa valve,

actuator, andextra temperaturesensor.The “xx”indicatesthe valvetypefrom the3 choicesbelow:

-1P 1.5”PositiveSeal

-2P 2”Positive Seal

TheECOMMAND4 is compatible with standard valve actuators manufactured by Hayward,Pentair/

Compool,and Jandy. Seediagramon page 5 forthelocationof valve connectors.

HeaterControl

The ECOMMAND 4 provides a set of low voltage dry contacts that can be connected to most gas

heatersorheatpumpswith24Vcontrol circuits. Referto thediagram onthefollowingpageforageneric

connection. Themanualssuppliedwithmostheatersalsoincludespecificwiringinstructionsforconnecting

theheatertoanexternalcontrol(usuallyidentifiedas“2-wire”remotecontrol).Formillivoltorlinevoltage

heaters,contact GoldlineTechsupport,908-355-7995. Referto thediagrams andthe informationon the

followingpages formore detailson theconnection toseveralpopularheaters.

Allow Low Speed

Thismenu only appearsif the poolfilter is configured for 2-speed or variable speed operation.

During default operation, high speed mode is used whenever the solar heater is on. IfAllow

LowSpeed is enabled, low speed pump operation will be allowed during solar heating except

for the first 3 minutes after solar heat turns on.

Lights Pump Spd

Settings Menu

Select between Settings Menu (default) and the desired pump speed

only if filter pump is set to variable

and relay type is set to standard

Move to previous/next configuration menu

Lights Config.

+ to view/change

Lights Function

Manual On/Off

Lights Relay

Standard

Push to access Lights options

Rotates between

Manual On/Off (default), Countdown Timer,

Low Speed- Filter, Timeclock, Solar, and Super Chlorinate

Toggle between Standard (default) and Dimmer

Move to previous/next configurationmenu

Move to next menu item

Move to next menu item or previous/next configuration menu

Lights Interlock

Disable

Lights Freeze

Disable

Toggle between Enabled and Disabled (default) Lights Interlock

Toggle between Enabled and Disabled (default) Lights Freeze

Move to next menu item

Move to next menu item or previous/next configuration menu

super chlorinate, and low speed

or all functions except dimmer relay, solar

super chlorinate, and low speed

or all functions except dimmer relay,

for manual on/off, countdown

timer and timeclock functions

Lights Function

Although designated as the “Lights” output, the function of the lights relay is similar to the

aux1and aux2 relays. If poollights are wired tothe lights relay, some options including Solar

function,Low Speed of a 2-SpeedFilter Pump, Lights Interlock and Lights Freeze Protection

will not be necessary and should be disabled. If no pool lights are used, the lights relay can

be used to control other pool devices that may require these options. The function of each

option is shown below.

Manual On/Off (default)—the lights relay will alternate between turning on and off when

the LIGHTS button is pressed. There is no automatic control logic.

Countdown Timer—the lights relay will turn on when the LIGHTS button is pressed. The

lightsrelay will turn off automaticallyafter aprogrammed time(see TimersMenu inOperation

Manual). The LIGHTS button can also be used to turn the output off.

Low Speed of a 2-speed Filter Pump – the ECOMMAND 4 will turn on the lights relay

whenever the low speed operation of the filter pump is required. It is very important that the

“2-speed”filter pumpoption be selected under the “Filter Config.”Menu forproper operation.

Timeclock – the lights relay will turn-on and turn-off at the times set for the lights timeclock

in the Timers Menu (see Timers Menu in Operation Manual). The LIGHTS button can also

be used to turn the output on and off.

Solar – the lights relay can operate a solar booster pump which will turn on when the filter

pump is running and solar heat is available and the water is less than the desired temperature

setting. It is important to note that “Solar Control” must be enabled in the “Solar Config.”

menu for proper operation to occur.

GenericHeaters

1. Wireheaterto120/240Vpowersource perthe instructionsintheheatermanual. TheECOMMAND

4doesNOTcontrol the power going to the heater.

2. Wire theECOMMAND4 drycontactheateroutputper thediagrambelow. Manyinternalpartsofthe

heatercangetveryhot--seetheheatermanufacturer’srecommendationsontheminimumtemperature

ratingfor wires. If noguidance is given,use 105°C ratedwire.

3. Set any ON/OFF switch on the heater to ON.

4. Set thethermostat(s) ontheheatertothemaximum(hottest) setting.

LaarsHeaters

1. Turnpower off toheater.

2. Removefactoryjumperfromterminalblock.

3. Wire ECOMMAND 4 to the heater as shown.

4. Ensuretoggle switchisin theONposition.

5. Setheater thermostatsto maximumposition.

Ignition/Valve

Heater

Kill Switch Thermostat

Air

Solar

Pool/Spa

Heater

Solar

Pool/Spa

Heater

to limit switches

remove jumper

Fusible Link

white

Heater Extend

If “Enabled”, the filter extend logic keeps the filter pump running beyond the normal turn-off

time until the pool (or spa) is heated up to the desired temperature setting (see Settings

Menu). Heater extend will NOT cause the filter pump to turn on, it will only delay the turn

off time when the heater is operating.

Allow Low Speed

This menu only appears if the filter is configured for 2-speed or variable speed operation.

During default operation, high speed mode is used whenever the heater is on. IfAllow Low

Speed is enabled, low speed will be allowed even if the heater is on.

Solar Config.

+ to view/change

Solar

Disabled

Solar-Extend

Disabled

Solar Priority

Disabled

Push to access solar options

Toggle between Enabled and Disabled (default) Solar

Toggle between Enabled and Disabled (default) Solar Extend

Toggle between Enabled and Disabled (default) Solar Priority

Move to previous/next configuration menu

Move to next menu item or previous/next configuration menu

Move to next menu item

if “Solar” is enabled

Allow Low Speed

Disabled

Toggle between Enabled and Disabled (default)

Move to

next menu item or previous/next configuration menu

if “Solar” is enabled and

“1-speed Filter” is not selected

Solar

If the solar control logic is “Enabled”, several additional steps must be taken to ensure

proper operation of the solar system. If the solar is operated by a valve, then the Valve3

output must be setup for solar logic (page 22). If the solar is operated by a pump, then one

of the AUX relays must be set up for solar logic (page 20). Also, the “solar” temperature

sensor must be installed. This sensor is typically mounted near the collector array and is

used to sense whether sufficient solar heat is available.

Ifsolar is “Enabled”, the valve or solar pump relay will turn on when the water temperature is

less than the desired temperature settingAND the solar sensor is hotter than the water. The

desiredtemperature is in the “SettingsMenu”. If applicable, the homeowner will be prompted

to enter separate pool and spa desired temperature settings. Depending on the position of

the pool/spa suction valve, the proper temperature setting will be used.

Solar Extend

If “Enabled”, the filter extend logic keeps the filter pump running beyond the normal turn-off

time if solar heat is still available. When solar heat is no longer available, both the solar

valve/pump and filter pump will turn off simultaneously. Solar extend will NOT cause the

filter pump to turn on, it will only delay the turn off time when solar is operating.

Solar Priority

If both “Solar Control” and “Heater Control” are enabled, the Solar Priority feature will keep

the conventional heater off whenever solar heat is available. This provides the most cost

effective way of heating the pool. When solar heat is not available, the conventional heater

willoperate normally.

HaywardHeaters

Refertotheinstructionsintheheater manualfor “2-wireRemote Thermostat”operation under“Remote

ControlConnections”and thediagrambelow:

1. Turnoffpowerto heater.

2. WireECOMMAND 4 to terminals1&2 (see diagram).

3. Leave jumper attachedtoterminals 4 &5.

4. Move “BYPASS”dipswitch onheatercircuit boardto“ON” position (up).

5. Turnheaterpowerback on.

6. Switch heater to either “Pool” or “Spa” (it doesn’t make any difference which is selected, the

ECOMMAND4 will takecontrol).

7. Heater displayshouldbe “bO” (for“bypassOn).

8. Heaterwillfire wheneverECOMMAND4requests(whenECOMMAND4 “Heater”LEDisillumi-

nated).

Pentair/Purex/MiniMax

1. Turnpower off toheater.

2. Removefactoryinstalledjumperfrom the“Ext Switch”connector.

3. Wire the ECOMMAND 4 tothe“ExtSwitch”connector as shown below.

4. Thewires to the ECOMMAND4must be separated fromanyline voltage wires. Failuretofollow

theseinstructions maycause erraticoperationoftheheater.

5. Setthe Power (Thermostat Select) switchtoeither“Pool” or “Spa”.

6. Setthe “Pool”and “Spa”thermostats totheirmaximumsettings.

Highest Speed

This is the highest speed that the variable speed pump is allowed to run at. It is used as the

upper limit in the High Speed Settings Menu. Also, this is the speed that the pump will run

at during the first 3 minutes of operation anytime the pump has been off for more than 30

seconds. Set highest speed from 20% to 100% (default).

Freeze Protection

Freeze protection is used to protect the pool and plumbed equipment against freeze damage.

Iffreeze protection isenabled and theAIR temperature sensor fallsbelow the freeze threshold

(see below), the ECOMMAND 4 will turn on the filter pump to circulate the water. If “Pool

and Spa” is selected in the Pool/Spa sub-menu (see page 22), the valves will also alternate

between the pool and spa every 30 minutes and the filter pump will turn off while the valves

are turning. The chlorinator will not operate if freeze protection is the only reason the pump

is running.

Freeze Protection Speed

This menu only appears if freeze protection is enabled and the pump is configured for 2-

speed or variable speed pump operation. This is the speed that the pump will run at during

freeze protection operation. Select high (default) or low speed operation.

Freeze Protection Temperature

Select the temperature to be used for freeze protection. Temperature is adjustable from 33ºF

- 42ºF (1ºC - 6ºC). 38ºF (3ºC) is default. This threshold will be used for all outputs that have

freeze protection enabled.

Heater1 Config.

+ to view/change

Heater1

Disable

Heater1 Cooldown

Disabled

Heater1 Extend

Disabled

Push to access heater options

Toggle between Enabled and Disabled (default) Heater 1

Toggle between Enabled and Disabled (default) Heater 1 Cooldown

Toggle between Enabled and Disabled (default) Heater 1 Extend

Move to previous/next configuration menu

Move to next menu item or previous/next configuration menu

Move to next menu item

Move to previous/next configuration menu

if “Heater1” is enabled

Allow Low Speed

Disabled

Toggle between Enabled and Disabled (default)

Move to

next menu item or previous/next configuration menu

if “Heater1” is enabled and

1-speed filter pump is not selected

Heater1

If the heater is “Enabled”, the heater relay will turn on when the water temperature is less

than the desired temperature setting and the filter pump is running. The desired temperature

is in the “Settings Menu”. If applicable, the homeowner will be prompted to enter separate

“pool” and “spa” settings. Depending on the position of the pool/spa suction valve, the

proper temperature setting will be used.

Heater Cooldown

This feature ensures that the heater cools down before water circulation is stopped. When

enabled,the ECOMMAND 4 will continueto run thefilter pump for 5 minutesafter the heater

turns off. During this period the filter pump LED will flash and also a “Heater Cooldown,

X:XX remaining” message will scroll on the display.

When the filter pump is running and the heater is on: Pressing the “Filter” button once will

cause the heater to turn off, but the filter pump will continue to run for heater cooldown (filter

LED flashing and message on display). Pushing the filter button a second time will override

the heater cooldown operation and turn the filter pump off.

Solar

Pool/Spa

Heater

Do not remove jumper

Terminal block located at

electrical junction box

Dipswitch located on heater

circuit board

ONºC

OFF

ºF

Solar

Pool/Spa

Heater

MINIMAX

Ext.

Switch

Remove

Factory Jumper

RaypakRP2100Pool/SpaHeater

1. Turnpower off toheater.

2. Pushthemodebuttonto“spa”mode.

3. Setthe temperaturetothe maximum.

4. Pushthe mode button to “OFF”.

5. Lastly, plug the prewiredconnectorin the P7 positiononthe board.

IMPORTANT: Theheaterwilldisplay“OFF”whenitisbeingremotelycontrolledbythe

ECOMMAND 4. Some homeowners see the “OFF” display and, thinking this is a mistake,

change the mode to “POOL” or “SPA” which then disables the remote control by the

ECOMMAND 4. To prevent this: Remove the heater touch pad connector (P5) which will

disablethetouchpad.

STA-RITEHeater

1. Turnpower off toheater.

2. Removeupperjacketandopen the control box.

3. Removethejumperforthe“fireman’s switch.

4. Wire to theECOMMAND4 using wire ratedfor105°C minimum.

Solar

Pool/Spa

Heater

Light Blue

Black

Orange Stripe

Orange

StripeBlack

RAYPAK RP2100

Drawing is for digital

heater. If heater is a

millivolt (analog),

run red wires from

Fireman’s Switch

to heater relay.

Solar

Pool/Spa

Heater

STA-RITE

Terminal

Board

Operating

‘Control

Fireman’s

Switch

If “Pool Only” is selected, then the ECOMMAND 4 will switch the pool/spa valves to the

“pool only” position at the start of the programmed pool filtering time period or when the

super-chlorinate function is turned on. This may be desirable on some systems with in-floor

cleaners because it allows the cleaner to operate all the time the pool is being filtered and/or

the super chlorinate is running.

V1=Aux1,V2=Aux2

This menu appears only if the Pool/Spa Setup is “Pool Only” or “Spa Only”. When enabled,

Valve1(return) will follow theAux1 output andValve2 (suction) willfollow theAux2output.

When disabled (default), the return and suction pool/spa valves function normally.

Filter Off Valve Change

This menu appears only if Pool/Spa setup is set to “Pool and Spa - Std”. When enabled

(default), the filter pump will shut off for 35 seconds whenever the Pool/Spa valves are

turning. The pump will NOT shut off when a heater is in Heater Cooldown mode.

Filter Config.

+ to view/change

Filter Pump

1 Speed

Freeze Protect

Enabled

Lowest Speed

10%

Highest Speed

100%

Push to access pump options

Rotates between 1-speed (default), 2-speed and variable speed options

Toggle between Enabled (default) and Disabled Freeze Protection

Adjust the lowest speed desired for variable speed operation

Adjust the highest speed desired for variable speed operation

Move to next menu item

Move to previous/next configuration menu

Move to next menu item or previous/next configuration menu

Move to next menu item

if “Variable Speed” is selected

Freeze Temp

38ºF

Freeze Protect

High Speed

Adjust the desired freeze protection temperature (33ºF - 42ºF)

Toggle between high speed (default) and low speed

Move to previous/next configuration menu

Move to next menu item

if “Freeze Protect” is enabled

and “1-speed Filter” is not selected

Filter Pump

For 2-speed pumps: When a 2-speed pump is configured, one of theAUX relays must also

be configured to control the low speed motor winding on the pump. Refer to the appropriate

sections in the Installation manual for specific information regarding the control logic for 2-

speed and variable speed pump operation.

For the Hayward Tristar variable speed pump: The Filter relay is used to supply input power

to the VSC pump control. The relay will be on when the filter pump output is on. When the

filter pump output is off, the relay will be off. On , off and speed is controlled by commands

sent to the pump.

Lowest Speed

This is the lowest speed that the variable speed pump is allowed to run at. It is used as the

lower limit in the Low Speed Settings Menu. Set lowest speed from 10% (default) to 50%.

HaywardVariableSpeedFilterPump:Refertothediagrambelowforproperlowvoltagecommunica-

tionwiring between the ECOMMAND4and the HaywardTristarVariableSpeed Control(VSC).

Usefour conductorcable(typically phonecable) forcommunicationsconnection betweenthe VSCand

theECOMMAND 4.The maximumwiring distanceis500feet(160meters). Notethat theterminals on

boththe VSCinterface boardandtheECOMMAND4 mainboard arenumbered. Theterminalconnec-

tionsshouldbematchedbetweenbothterminalblocks(connect1to1,2 to2, etc.). Thecommunications

cableshould beroutedthrough theknockouthole onthe left sideof theVSCenclosure, andawatertight

fittingshouldbeusedtokeep wateranddebris outoftheopening. Thecommunicationscableshouldalso

beroutedaway from the ECOMMAND 4 andVSCpowerconnections if possible.

VSCPumpAddressSetting

TheVSC addressmust beset to001whenusingtheVSCwith theECOMMAND4. Refer totheTriStar

PumpOwner’sManual(IS3220VSC) and Hayward documentIS3220VSCAQLLforspecificinstruc-

tionson settingthe pumpaddress.

TemperatureSensors

TheECOMMAND4 utilizes 10K ohm thermistor typesensors. Threesensors(water temperature, air

temperatureand solar temperature)are included. If theECOMMAND4 isbeingused to controlasolar

heatingsystem,the solarsensor isrequired. Thesensorsareprovided witha15ft.cable. If alongercable

isrequired,contact the Goldline service dept.forinformationon suitable cable types andsplices. See

page6andthediagrambelowforinstallationinformation.

Pool/Spa Config.

+ to view/change

Pool/Spa Setup

Pool and Spa

Spa Spillover

Enabled

Filter Operation

Spa Spillover

Push to access Pool/Spa options

Rotates between Pool Only (default), Spa Only and

Pool and Spa

Toggle between Enabled and Disabled Spa Spillover

(default)

Toggle between Pool Only and Spa Spillover options

(default)

Move to previous/next configuration menu

Move to next menu item

Move to next menu item or previous/next configuration menu

Move to previous/next configuration menu

if “Pool and Spa” is

selected and

if “Spa Spillover” is enabled

Spa - CountDn

00:30

Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15..., (default is 4:00))

Move to next menu item

if “Pool and Spa” is selected

V1=Aux1, V2=Aux2

Disabled

Toggle between Enabled and Disabled

(default)

if “Pool Only” or “Spa Only” is selected

Move to previous/next configuration menu

Filter Off Valve

Change: Enabled

Toggle between Enabled and Disabled(default)

if “Pool and Spa” is selected

Move to previous/next configuration menu

Pool/Spa Setup

If “Pool Only” or “Spa Only” are selected, then the pool/spa valves are not needed and

pushing the POOL/SPAbutton on the display/keypad will have no effect. If “Pool and Spa”

is selected, then the pool/spa suction and return valve actuators should be connected to the

ECOMMAND 4. Pressing the POOL/SPA button on the display/keypad will allow the

homeowner to alternate between pool and spa operation. For more information on “Pool and

Spa”, refer to the Plumbing section on pages 8.

Spa CountDn

This menu will appear only if Pool/Spa Setup is set to “Pool and Spa”. This setting is the

time, after you manually switch the Pool/Spa valves to “Spa Only”, until the ECOMMAND

4 automatically returns the valves to their previous positions. It is programmed in increments

of5 minutes, from“Manual On/Off” (0minutes) to “21:00”(21 hours). The filteris forced on

during this time period.

Spa Spillover

When spa spillover is “Enabled” and “Pool and Spa”, the homeowner will be able to rotate

through “Pool Only” (both suction and return valves switched to pool), “Spa Only” (both

suction and return valves switched to spa) and “Spillover” (suction valve switched to pool

and return valve switched to spa) by successive presses of the “Pool/Spa button.

Filter Operation

If “Spa Spillover” is selected, the ECOMMAND 4 will automatically switch the pool/spa

suction and return valves to “spillover” at the start of the programmed pool filtering time

period or when the super-chlorinate function is turned on. The valves will remain in this

position for the remainder of the super-chlorinate period. This option is usually preferable

because both the pool and spa water will be filtered and sanitized.

GRN

YEL

BLK

RED

GRN

YEL

BLK

RED

VSC

Connect screw terminals

“1” to “1”, “2” to “2”, etc.

Solar

Pool/Spa

AIR

SENSOR

SOLAR/SPA

SENSOR

POOL/SPA

SENSOR

4. Configuration Setup

After plumbing and wiring are complete, the ECOMMAND 4 MUST BE CONFIGURED before at-

temptingto operate. Configurationinformation isentered atthekeypadand“tells”theECOMMAND 4

whatequipment isconnectedand howeach shouldbecontrolled.

Accessing the Configuration Menus

Configuringthe ECOMMAND4requires that younavigate through theConfiguration Menu andinput

variousinformation. Formore detailedinformation aboutusingtheECOMMAND4 menusystem,refer

tothe OperationManual.

To access the Configuration Menu

Configuration

Menu-Unlocked

Configuration

Menu-Locked

Press repeatedly until “Configuration Menu” is displayed

Move to configuration menu items

Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock

NOTE: The configuration menu automatically “locks” after 2 minutes of no buttons being

pressed to prevent unauthorized people from changing the control logic inadvertently and

possibly damaging the pool equipment or causing a “call back” to fix the configuration.

Configuration Menu Items

Eachitem needstobe programmed andmay contain additionalsub-menu items. Refer tothe following

pagesforinformationonprogramming.

Move to next menu item

Ext. Chlorinator

Enabled

Display

Salt

Chlor. Config.

+ to view/change

Toggle between Display Salt (default) and Minerals

Toggle between External Chlorinator Enabled and Disabled (default)

Move to previous/next configuration menu

Move to next configuration menu

Push to access Chlorinator option

Chlorinator

If the optional external chlorinator is enabled (requires the use of a Goldline Aqua Rite or

HaywardSwimpure chlorinator), the ECOMMAND 4 will automatically chlorinate both the

pool and spa according to the desired output setting (see Settings Menu in the Operation

manual). If disabled (default), all displays relating to the chlorinator will be suppressed.

When the chlorinator is enabled, the ECOMMAND 4 will automatically detect and control

anyAqua Rite/Swimpure(s) that is installed in the system (see page 13).

Display

Allows for the display of salt (default) or mineral values.

BaseStation

Pluginthe pigtailconnectorfrom thewirelessbasestationintothe“wireless”connectoronthemainPCB

inthe ECOMMAND4control unit.

GoldlineAquaRiteorHaywardSwimpureChlorinator

TheECOMMAND4 can control one or more GoldlineAquaRiteor Hayward Swimpure chlorinators

whenadditionalsanitizingcapacity isrequired. A4wireconnectionisusedtocommunicate totheAqua

Rite/Swimpure and can be wired up to 500' apart. Any outdoor rated 4 conductor cable can be used.

Refertothewiringdiagramsbelowforproperwiringconnectionto theAquaRite/Swimpure.NOTE:

Theremustbeonly1"primary"unit. AllotherAquaRite/Swimpureunitsmustbeconfiguredas"second-

ary".

Ecommand 4 Aqua Rite

Swimpure

(Primary)

Aqua Rite

(Secondary)

Swimpure

Additional

qua Rite/Swimpure(s)

(if required)

Jumper Removed

For Secondary(s)

Jumper Installed

For Primary

(Factory Default)

GREEN

YELLOW

BLACK

RED

NOTE: Primary/Secondary jumper is located underneath small circuit board.

AQL2-BASE-RF

Base Receiver

Tighten nut

Main PCB

Connector for

Base Receiver

GRN GRN

BLK BLK

YEL YEL

RED RED

ECOMMAND 4 Aqua Rite

Swimpure

green

yellow

black

red

4. Configuration Setup

After plumbing and wiring are complete, the ECOMMAND 4 MUST BE CONFIGURED before at-

temptingto operate. Configurationinformation isentered atthekeypadand“tells”theECOMMAND 4

whatequipment isconnectedand howeach shouldbecontrolled.

Accessing the Configuration Menus

Configuringthe ECOMMAND4requires that younavigate through theConfiguration Menu andinput

variousinformation. Formore detailedinformation aboutusingtheECOMMAND4 menusystem,refer

tothe OperationManual.

To access the Configuration Menu

Configuration

Menu-Unlocked

Configuration

Menu-Locked

Press repeatedly until “Configuration Menu” is displayed

Move to configuration menu items

Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock

NOTE: The configuration menu automatically “locks” after 2 minutes of no buttons being

pressed to prevent unauthorized people from changing the control logic inadvertently and

possibly damaging the pool equipment or causing a “call back” to fix the configuration.

Configuration Menu Items

Eachitem needstobe programmed andmay contain additionalsub-menu items. Refer tothe following

pagesforinformationonprogramming.

Move to next menu item

Ext. Chlorinator

Enabled

Display

Salt

Chlor. Config.

+ to view/change

Toggle between Display Salt (default) and Minerals

Toggle between External Chlorinator Enabled and Disabled (default)

Move to previous/next configuration menu

Move to next configuration menu

Push to access Chlorinator option

Chlorinator

If the optional external chlorinator is enabled (requires the use of a Goldline Aqua Rite or

HaywardSwimpure chlorinator), the ECOMMAND 4 will automatically chlorinate both the

pool and spa according to the desired output setting (see Settings Menu in the Operation

manual). If disabled (default), all displays relating to the chlorinator will be suppressed.

When the chlorinator is enabled, the ECOMMAND 4 will automatically detect and control

anyAqua Rite/Swimpure(s) that is installed in the system (see page 13).

Display

Allows for the display of salt (default) or mineral values.

BaseStation

Pluginthe pigtailconnectorfrom thewirelessbasestationintothe“wireless”connectoronthemainPCB

inthe ECOMMAND4control unit.

GoldlineAquaRiteorHaywardSwimpureChlorinator

TheECOMMAND4 can control one or more GoldlineAquaRiteor Hayward Swimpure chlorinators

whenadditionalsanitizingcapacity isrequired. A4wireconnectionisusedtocommunicate totheAqua

Rite/Swimpure and can be wired up to 500' apart. Any outdoor rated 4 conductor cable can be used.

Refertothewiringdiagramsbelowforproperwiringconnectionto theAquaRite/Swimpure.NOTE:

Theremustbeonly1"primary"unit. AllotherAquaRite/Swimpureunitsmustbeconfiguredas"second-

ary".

Ecommand 4 Aqua Rite

Swimpure

(Primary)

Aqua Rite

(Secondary)

Swimpure

Additional

qua Rite/Swimpure(s)

(if required)

Jumper Removed

For Secondary(s)

Jumper Installed

For Primary

(Factory Default)

GREEN

YELLOW

BLACK

RED

NOTE: Primary/Secondary jumper is located underneath small circuit board.

AQL2-BASE-RF

Base Receiver

Tighten nut

Main PCB

Connector for

Base Receiver

GRN GRN

BLK BLK

YEL YEL

RED RED

ECOMMAND 4 Aqua Rite

Swimpure

green

yellow

black

red