Health O Meter 402KL User manual

Model 402KL
Physician Beam Scale
User Instructions
PELSTAR, LLC 9500 West 55th Street, McCoo , IL 60525k
P/N UM402KL Rev20150526 1

Model 402KL
Thank you for your purchase of this Health o meter®Professional product. Please read this
manual carefully, and keep it for easy reference or training.
TABLE OF CONTENTS
Caution and Warning.................................................................................................3
Specifications for This Scale.....................................................................................3
Certifications / Disposal / Service..............................................................................4
Assembly Instructions 402KL Scale .........................................................................5
Transportation ..........................................................................................................10
Operating Instructions...............................................................................................13
Counterweight Instructions........................................................................................16
Height Measurement Instructions..............................................................................21
Troubleshooting ........................................................................................................23
Maintenance..............................................................................................................24
Warranty....................................................................................................................25
Note: This scale has been factory calibrated, and does not
require calibration prior to use.
Please register your scale for warranty coverage at:
www.homscales.com
For User Instructions updates and revisions please go to:
www.homscales.com
2

3
CAUTION AND WARNING
To prevent injury and damage to your scale, please follow these instructions very
carefully.
To prevent injury, as well as scale damage during assembly, exercise
caution when assembling the scale pillar.
Assemble and operate the scale per the enclosed user instructions.
For accurate weighing, this scale must be placed on a flat, stable surface.
For accurate weighing, verify before each use the proper operation
according to the procedure described in this manual.
Do not transport the scale with any weight on the platform.
Do not exceed recommended weight limit of 390 lb / 180 kg or 490 lb /
210 kg with optional counterweights for this scale.
Do not use in the presence of flammable or explosive materials.
If the scale becomes damaged, it should not be operated until properly serviced. All
repairs should only be performed by authorized Health o meter®Professional
service personnel.
To prevent patient injury, the patient must be attended throughout the
entire weighing event.
Patient should wear socks or other form of lightweight foot covering during
weighing event.
SPECIFICATIONS FOR THIS SCALE
General
The Model 402KL physician beam scale employs a proven and rugged mechanical design to
measure patient weight and height. Each precision scale is designed to provide accurate,
reliable, and repeatable weight measurements. In addition, each scale is designed to provide
the user with features that make the weighing process simple, fast, and convenient.
Weight is displayed in pounds (lb) or in kilograms (kg). Height is displayed in inches (in) or in
centimeters (cm).
402KL Scale Specifications
Capacity: 390 lb (180 kg)
Capacity with optional
counterweights: 490 lb (210 kg)
Environmental: Operating temperatures: 50°F to 104°F (10°C to 40°C)
Storage temperatures: 50°F to 104°F (10°C to 40°C)
Maximum Humidity: 85% RH
Physical Dimensions: Scale (Overall Dimensions)
Width: 16-¾” (42.6 cm)
Depth: 20-1/4” (51.4 cm)
Height: 57-½” (146.1 cm)
Weight: 28 lb (12.7 kg)
Platform (Standing Area)
Width: 10-½” (26.7cm)
Depth: 14” (35.6 cm)
Height: 3-1/4” (8.3 cm)

CERTIFICATIONS / DISPOSAL / SERVICE
Certification Descriptions
Pelstar, LLC has been officially certified as the manufacturer
of Health o meter®Professional medical devices. The Pelstar,
LLC quality assurance system covers the development,
production, sales and service of medical scales and
measuring systems.
Products carrying this symbol meet the requirements of:
1.Directive governing medical devices 93/42/EEC
402KL Scale Disposal
This Health o meter®Professional scale must be disposed of properly as steel waste. Follow
the national, regional or local regulations which apply to you for disposal of steel waste.
CUSTOMER SERVICE INFORMATION
The 402KL physician beam scale is shipped disassembled in one carton. Carefully inspect the
carton for shipping damage before unpacking. If damage is found, contact Customer Service.
For further information or telephone support, please contact Customer Service at:
Telephone: [phone]
Email: [email protected]
4

5
402KL ASSEMBLY INSTRUCTIONS
Before Assembly
Each 402KL physician beam scale is shipped disassembled in one carton. Carefully inspect the
carton for shipping damage before unpacking. If damage is found, contact your shipper or a
Health o meter®Professional representative immediately. Claims must be filed with the shipper
as soon as possible after receipt of the package. The following information details what you will
find inside the main carton as you unpack the parts for assembly.
To prevent scratching any components and avoid damaging the scale parts when unpacking, do
not use a box cutter, knife, scissors, or any sharp object to open the protective inner packaging.
Carefully remove each assembly from the carton and unwrap the packing materials. Set the
carton aside for storage.
Parts List
Carton
(1) Scale platform
(1) Pillar with height rod attached
(4) Pillar nuts
(1) User instructions
(1) Wrench
Tools Required
Wrench (included)

6
402KL ASSEMBLY INSTRUCTIONS (CONTINUED)
Assembling the 402KL Scale (Refer to Figures 1 - 6 on pages 7- 9)
Caution: It is recommended that the assembly be performed by two persons.
1. Carefully remove the scale platform and pillar from the carton. Place the scale platform and
pillar on a flat, level, and dry surface. Using a table can be helpful for assembly of 402KL
scale (see Figures 1 & 5 on pages 7 & 9).
2. Remove the four pillar nuts and wrench from the carton.
3. Locate the steel rod at the base of the pillar (see Figures 4, 5 & 6 on pages 8 & 9).
4. Cut the tie wrap that holds the steel rod to the pillar studs (see Figure 3 on page 8).
5. Insert studs into the four holes provided in the scale platform (See Figure 2 on page 7).
6. Tip the scale platform at an angle, resting the top of the pillar on any convenient support.
Using the wrench provided, secure the pillar to the scale platform with the four nuts (see
Figures 4 & 5 on pages 8 & 9).
7. Pull the steel rod toward the base of the scale platform by grasping the finger pull loop on the
steel rod end (see Figures 4, 5 & 6 on pages 8 & 9).
8. Push the lever extension toward the pillar with your hand (see Figure 4, 5 & 6 on pages 8 &
9).
9. While holding this position, hook the steel rod to the hole at the end of the lever extension.
Release the finger pull loop and ensure that the steel rod and lever extension is hooked
together.
10. Carefully position the scale to its upright position.
11. The scale is now assembled and is ready for use (see Figure 1 on page 7).
Note: To transport your scale, acquire the optional wheel bracket (Part Number # 55000). Please
refer to the “Transportation” section for assembly instruction.
Note: To increase your scale’s capacity, acquire the optional counterweight set (Part Number
# 55090). Please refer to the “Counterweights” section for user instruction.

402KL ASSEMBLY INSTRUCTIONS (CONTINUED)
402KL Assembly
Figure 1
Figure 2
7

402KL ASSEMBLY INSTRUCTIONS (CONTINUED)
Tie wrap
Figure 3
8
Pillar nuts
Finger pull
loop
Studs
Finger pull
loop
Figure 4

402KL ASSEMBLY INSTRUCTIONS (CONTINUED)
Figure 5
Pillar nuts Finger pull
loop
Steel rod
Lever extension
Figure 6
9

10
TRANSPORTATION
Preparing a 402KL Scale for Transportation (see Figures 7-10 on pages 11 & 12)
This scale can be easily assembled with a wheel bracket (Part Number 55000, see Figure 7 on
page 11) for storage, or for transport from one room to another. This scale does not include
55000 Wheel Bracket, and must be acquired separately. To prepare the scale for transport,
follow these steps:
Caution: It is recommended that the assembly be performed by two persons.
1. Remove the mounting screws attaching the clamping plate to the wheel bracket. (See
Figure 8 on page 11)
2. Tip the scale forward until top front of the pillar is resting on the floor.
3. Position the clamping plate inside the base, and align the clamping plate, wheel bracket,
and base assembly holes. (See Figure 9 on page 12)
4. Install the mounting screws through the wheel bracket, base, and clamping plate.
Tighten the mounting screws securely. (See Figure 10 on page 12)
5. Carefully tip the scale to its upright position.
6. To transport the scale, tip the scale pillar back until the scale is supported by the wheel
bracket. Carefully move the scale to its new location.
Required Parts
(1) 402KL
(1) Wheel Bracket (Part Number 55000)
Note: Wheel bracket is not included.
Tools Required (not included)
Adjustable wrench or 10mm wrench

TRANSPORTATION (CONTINUED)
11
55000 Wheel bracket
Figure 7
Figure 8

TRANSPORTATION (CONTINUED)
Figure 9
Wheel Bracket
Clamping plate
Mounting screws
Base
Figure 10
12

13
OPERATING INSTRUCTIONS
Zero Balance Adjustment (see Figures 11 – 12 on page 14)
The scale should be checked periodically, particularly when moved, by following the instructions
below:
Note: A flat head screwdriver is required.
1. Ensure that the scale is located on a hard, flat, and level surface. Step on and off scale
several times in order to align all internal parts.
2. Place both poise weights on the “0” value on both bars. The beam pointer should float gently
up and down, and not touch the top or bottom of the trig-loop.
3. If the beam pointer is not centered in the trig-loop opening, rotate balance ball screw to
correct the beam pointer.
Weighing Instructions (See Figure 13 on page 15)
1. Set the large and small poises to indicate the patient’s approximate weight.
2. Have patient step onto the scale. Ensure they are positioned directly in the center of the
platform. Continue to adjust the small and large poise weights until the pointer is centered.
Note: It is not necessary for you to wait for the pointer to stop moving in order to read the
correct weight. As long as the pointer is moving equally within the trig-loop opening, the
patient’s weight can be determined.
3. The patient weight can be recorded in either pounds or kilograms.
4. Observe the location of the indicator arrow built into each poise weight. Read the value on
the poise bar, closest to the indicator arrow.
5. For easy identification, pounds (lb) have black graduations on a silver background, located
on the upper portion of each poise bar; kilograms (kg) have silver graduations on a black
background, located on the lower portion of each poise bar.
6. Add the indicated reading of the small poise value to the indicated reading of the large poise
value. The total amount is the patient’s weight.

OPERATING INSTRUCTIONS (CONT)
14
Upper poise bar
Lower poise weight
Pointer
Upper poise weight
Balance ball screw Lower poise bar
Pillar head Pillar
Figure 11
Pounds (lb)
Kilograms (kg)
Trig loop
Balance ball
Figure 12

OPERATING INSTRUCTIONS (CONT)
Indicator
Indicator Value reads 100 lb
Value reads 13.5 kg Combined value: 100 lb +
29.75 lb = 129.75 lb
- or -
Combined value: 45.4 kg
13.5 kg = 58.9 kg
Value reads 29.75 lb
Value reads 45.4 kg
Figure 13
15

16
COUNTERWEIGHT INSTRUCTIONS
Counterweight Instruction (see Figures 14 – 20 on page 18 - 20)
In order to increase the scale’s capacity to a maximum value of 490 lb / 210 kg, the
counterweight set (55090, see Figure 14 on page 18) must be acquired. The scale can be easily
assembled with a counterweight set (Part Number 55090 for whole set, 55080 for counterweight
in pounds, and 55085 for counterweight in kilograms).
In order to employ the counterweight set, refer to the instructions below. Contact technical
support with any questions or concerns regarding the use of the counterweight set.
Counterweight Instructions for Weighing in Pounds (lb)
Note: The 100 lb counterweight is required when weighing a patient who is over 390 lbs.
Counterweight Instructions for Weighing a Patient 391 - 400 (lb)
1. When a patient weighs between 391 - 400 lb, place the lower poise weight at 250 lb. (See
Figure 16 on page 19)
2. Place the 100 lb counterweight on the 3rd notch from the left, between the 50 and 100 lb
value. (See Figure 15 on page 18)
3. Adjust the small poise weight to match the patient weight. The poise bar will center in the
trig-loop.
Note: To read a patient weight, refer to: “Recording a Patient Weight” section below.
4. Read and record the weight.
Counterweight Instructions for Weighing a Patient 401 - 440 (lb)
1. When a patient weighs between 401 - 440 lb, place the lower poise weight at 300 lb. (See
Figure 17 on page 19)
2. Place the 100 lb counterweight on the 3rd notch from the left, between the 50 and 100 lb
value. (See Figure 15 on page 18)
3. Adjust the small poise weight to match the patient weight. The poise bar will center in the
trig-loop.
Note: To read a patient weight refer to, “Recording a Patient Weight” section below.
4. Read and record the weight.
Counterweight Instructions for Weighing a Patient 441 - 490 (lb)
1. When a patient weighs between 441 - 490 lb, place the lower poise weight at 340 lb. (See
Figure 18 on page 19)
2. Place the 100 lb counterweight on the 3rd notch from the left, between the 50 and 100 lb
value. (See Figure 15 on page 18)
3. Adjust the small poise weight to match the patient weight. The poise bar will center in the
trig-loop.
Note: To read a patient weight refer to, “Recording a Patient Weight” section below.
4. Read and record the weight.

17
COUNTERWEIGHT INSTRUCTIONS (CONT)
Counterweight Instructions for Weighing in Kilograms (kg)
Note: The 30 kg counterweight is required when weighing a patient who is over 170 kg.
Counterweight Instructions for Weighing a Patient 171 - 190 (kg)
1. When a patient weighs between 171 - 190 kg, place the lower poise weight at 140 kg.(See
Figure 19 on page 20)
2. Place the 30 kg counterweight on the 3rd notch from the left, between 20 and 40 kg value on
the lower poise bar. (See Figure 15 on page 18)
3. Adjust the small poise weight to match the patient weight. The poise bar will center in the
trig-loop.
Note: To read a patient weight refer to: “Recording a Patient Weight” section below.
4. Read and record the weight.
Counterweight Instructions for Weighing a Patient 191 - 210 (kg)
1. When a patient weighs between 191 - 210 kg, place the lower poise weight at 160 kg. (See
Figure 20 on page 20)
2. Place the 30 kg counterweight on the 3rd notch from the left, between 20 and 40 kg value on
the lower poise bar. (See Figure 15 on page 18)
3. Adjust the small poise weight to match the patient weight. The poise bar will center in the
trig-loop.
Note: To read a patient weight refer to: “Recording a Patient Weight” section below.
4. Read and record the weight.
Recording a Patient Weight
To read the patient’s weight, add the weight value indicated on the lower and upper poise bars,
along with the counterweight at the 3rd notch on the lower poise bar.
For example: If a patient weighs 441 lb:
1. When a patient weighs 441 lb, place the lower poise weight at 340 lb.
2. Place the 100 lb counterweight on the 3rd notch from the left, between the 50 and 100 lb
value.
3. Adjust the small poise weight to match the patient weight. The poise bar will center in the
trig-loop.
4. Add the weight value indicated on the upper and lower poise bars, as well as the additional
100 lb counterweight:
340 lb + 1 lb + 100 lb = 441 lb
Patient’s weight is: 441 lb

COUNTERWEIGHT INSTRUCTIONS (CONT)
Counterweight Set (55090)
Figure 14
3r
d
Notch from the left
Figure 15
18

COUNTERWEIGHT INSTRUCTIONS (CONT)
391 - 400 lb Assembly
Figure 16
401 - 440 lb Assembly
Figure 17
441 - 490 lb Assembly
Figure 18
19

COUNTERWEIGHT INSTRUCTIONS (CONT)
171 - 190 kg Assembly
Figure 19
191 - 210 kg Assembly
Figure 20
20