Heatstore HSQWPH1500N User manual

HSQWPH1500N
Quartz Weatherproof Heater
Installation and Operating Instructions
Telephone: [phone] Fax: [phone]
Victoria Road, Avonmouth, Bristol BS11 9DB
www.heatstore.co.uk
Maintenance
The heater contains no moving parts and therefore very little maintenance
is required other than to ensure that
there is no excessive build-up of dust/dirt on the reflectors or emitters
as this can cause overheating and premature emitter failure.
To clean the appliance, turn off and disconnect from mains supply,
allow to cool then wipe with a damp cloth.
Lamp Replacement
The lamp used in the fitting is robust and if knocks and shock vibrations are
avoided, will last for around 5000 hours.
To replace the lamp:
Disconnect the heater from the power supply by unplugging from the mains
socket and wait until the body has cooled down.
Remove both end caps by undoing the 2 socket head screws at each end.
Remove the guard and end reflectors.
Unclip the lamp from the spring clips at each end, allowing the emitter to
move forward clear of the back reflector.
Unclip the reflector from the heater casing.
Disconnect the emitter wires from the terminals located in the electrical box
on the rear of the heater, and then remove the lamp.
Insert the wires of the new lamp through the holes in the heater body to the
electrical box and reconnect them into the terminals. Ensure that the
terminals are tightened correctly to make a good electrical connection.
Re-assemble making sure all the parts are replaced and the guard is in
position IMPORTANT SAFEGUARDS
WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
IF IN ANY DOUBT ABOUT THE INSTALLATION OR USE OF THIS
PRODUCT, CONSULT A COMPETENT ELECTRICIAN.
Issue 2 0910
Waste electrical products should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authority or
retailer for recycling advice.
Specification
HSQWPH1500N:
1500W; 230-240V ~50Hz; 6.5A
IP
55
F
HSQWPH1500N[10]instructions 7/9/10 10:46 Page 1

Models covered by these
instructions:
HSQWPH1500N – 1.5kW
Quartz Weatherproof
Heater.
HSQWPH1500RL – 1.5kW
Replacement Lamp for
the above.
Before installation
The heater should be
mounted horizontally
where possible or at a
maximum angle of 35
degrees from the
horizontal using the
mounting brackets
provided to ensure
adequate clearances.
If mounted on Parasols
ensure the heater is left
to completely cool
before closing.
A minimum air gap of
500mm should always
be allowed between the
top of the heater and the ceiling, roof or canvas.
A safety distance of 1metre should always be left in front of the heater.
Heaters should not be installed in areas where hazardous vapours may be
present as defined in BS5345
This fitting is rated class I and IP55 suitable for outdoor use. To maintain
the protection rating all connections to the mains must be done with a
minimum of IP55 equipment.
Ensure that there is no possibility of inflammable material coming into
contact with the heater, or is too near the heater.
The essential element of the heater is the halogen filled quartz linear lamp
with a tungsten element. This operates at about 1600°C and emits short
wave infrared radiant heat.
The lamp operates at full output almost instantly and emits a radiant
energy of 1.6 – 1.8 microns.
Important Safeguards
After unpacking make sure that the appliance is complete and shows no
signs of visible damage or tampering.
Check the supply voltage is the same as indicated on the device.
Avoid improper use of extension cords.
DO NOT touch the heater with wet hands;
DO NOT operate the heater without the guard in position.
The heater should only be used with adult supervision.
Keep packing materials, which are potential dangers, away from children.
Installation
The mains lead is made from high temperature cable and as such should
not be replaced without consulting a suitable qualified electrician.
The fitting must always be installed using the mounting brackets provided.
This ensures correct positioning and adequate clearance.
This unit should be mounted at a minimum of 1800mm above ground level
(See figure 1 opposite) with a minimum air gap of 500mm maintained
above the heater and the ceiling or canopy.
A safety distance of 1metre should always be left in front of the heater.
Ensure that there is no possibility of inflammable material coming into
contact with the heater, or is too near the heater.
The fitting must be earthed.
Wall mounting
Remove the bracket from the back of the heater by unscrewing the 2 x M8
bolts.
Before drilling any holes ensure that the wall is solid and that there are no
water pipes or electrical wires in the area where you are placing the heater.
Secure the bracket to the wall then refit the heater to the bracket using the 2
x M8 bolts.
The heater must be mounted at an angle of between 45° and 90°.
(See figure 1 opposite).
Parasol mounting
Use the supplied bracket for clamping to a parasol arm. You must ensure
the canvas/material of the parasol is at least 500mm away from the back
of the heater. The parasol must not come into contact with the heater in
high winds when the heater is in use.
min 45°
max 90°
500mm
minimum
1800mm
minimum
1000mm minimum
Figure 1
The HSQWPH1500N is an easy to install weatherproof
Quartz Heater for wall-mounting or fixing to a parasol.
HSQWPH1500N[10]instructions 7/9/10 10:46 Page 3