Heatstore HS4212XNi User manual

overheating then plug the appliance in again. If it still cannot be reset,
contact Heatstore for advice.
CLEANING AND MAINTENANCE
Before cleaning always remove the plug from the electrical socket.
Clean the air inlet / outlet grilles frequently.
The external surfaces of the heater may be cleaned with a moist cloth.
Never use abrasive powders or solvents.
Ensure the product is thoroughly dry before re-using.
Telephone: [phone] Fax: [phone]
Victoria Road, Avonmouth, Bristol BS11 9DB
www.heatstore.co.uk
ISSUE 2: 1108
ONE YEAR
Waste electrical products should not be disposed of with household waste. Please recycle
where facilities exist. Check with your local authority or retailer for recycling advice.

SPECIFICATION
HS4212XNi 2000W; 240V; 50Hz
HS4212XNi Fan Heater
Operating Instructions
IMPORTANT SAFEGUARDS
WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
IF IN ANY DOUBT ABOUT THE INSTALLATION OR USE OF THIS
PRODUCT, CONSULT A COMPETENT ELECTRICIAN.
HS4212XNi[09]_instructions 2/12/08 11:33 Page 1

OPERATION OF THE HEATER
NOTE:- It is normal when the heater is turned
on for the first time or when turned on after
having not been used for a long period of
time for a smell to be emitted. This will
disappear when the heater has been on a
short while.
INSTALLATION
The appliance requires no installation.
It should be used solely as a portable
appliance. The use of extension leads is not recommended.
Portable appliances are not suitable for use in a bathroom.
OPERATION
Ensure the heater is on a flat, even surface.
Turn the thermostat knob in a clockwise direction until it reaches the
maximum setting.
Summer setting (ventilation only): turn the switch to setting
Heating at mid power: turn the switch to setting I(1000W)
Heating at full power: turn the switch to setting II (2000W)
Switching off: turn the switch to setting 
REGULATING THE THERMOSTAT
When the room has reached the required temperature turn the left
thermostat knob slowly in an anti-clockwise direction up to the point where
the appliance switches off and not beyond. The temperature fixed in this
way will be automatically regulated and kept at a constant level by the
thermostat.
NOTE:- The temperature control does not vary the fan speed.
AUTOMATIC SAFETY CUTOUT
The heater is fitted with a safety device which will switch off the heater in
case of accidental overheating (e.g. obstruction of air intake and outlet
grilles, motor turning slowly or not at all). To reset, disconnect the plug
from the power for approximately10 minutes, remove the cause of
FOR YOUR OWN SAFETY
1. Do not use the appliance in rooms less than 4m2area.
2. Only connect the fan heater to a single-phase socket with a main
voltage as specified on the rating plate.
3. Always use in an upright position.
4. Keep the air inlet and outlet free from objects: at least 1m in front and
500mm behind the heater. Keep combustible material such as
furniture, cushions, bedding, paper, clothes, curtains etc. at least 1m
away from the fan heater.
5. Do not hang anything on, or in front of the fan heater.
6. Always unplug the heater when not in use. Do not pull the cord to
unplug the heater.
7. Do not install the heater below a socket.
8. The air outlet gets hot during operation. Do not touch the hot surface.
Unplug the heater and allow to cool for 5 minutes before moving.
9. Do not cover.
10. Do not move the appliance while it is functioning in order to avoid
overheating.
11. Do not use this fan heater in the immediate surroundings of a bath,
shower or a swimming pool.
12. Do not use the fan heater in rooms with explosive gas or while using
inflammable solvents, varnish or glue.
13. Do not use outdoors or leave unattended while in use.
14. Take care when using this appliance near children, the elderly or
infirm.
15. If the power cord is damaged, the appliance malfunctions or is
dropped or damaged, stop using the appliance and contact Heatstore
for further instructions.
16. To avoid overheating, do not cover the cable and ensure it is fully
unwound.
17. Keep the fan heater clean. Do not allow any objects to enter any
ventilation or exhaust opening as this may cause electric shock, fire or
damage to the heater.
18. Store in a cool dry place when not in use.
THERMOSTAT
SWITCH
HANDLE
POWER
INDICATOR
Figure 1
32
HS4212XNi[09]_instructions 2/12/08 11:33 Page 3