HEIDELBERG Speedmaster SM 102 User manual

GR 009560002000000000
I.1
1 Preface Preset Plus feeder
1.1 Notes for the reader
Fig. 1 Operating manual
Target group
This operating manual is addressed to you as the
operator of the Preset Plus feeder. It is valid for all
Preset Plus feeders of this type series. It shows you
how you can operate the Preset Plus feeder and how
you can achieve good results quickly. Always have
this manual available in the vicinity of the printing
press.
Structure of the operating manual
The operating manual is subdivided into main chap-
ters and chapters. The main chapters are marked by
letters (A, B, C, ...).
The sub-chapters are marked by numbers
(1, 2, 3, ...).
The main chapter A Safety contains the information
that is required for working safely on the press.
The main chapter Bdescribes the function of the
electric controller.
The main chapter Cdescribes the mechanical com-
ponents of the Preset Plus feeder, and its operation
and adjustment.
The main chapter Ddescribes the maintenance of
the Preset Plus feeder.
The main chapter D Index helps you in finding spe-
cific information.
Each main chapter and each chapter starts with the
related table of contents.
Control panels and displays
This manual describes the maximum configuration of
the Preset Plus feeder. The control panels and dis-
plays on the Preset Plus feeder may therefore be
different. They depend on type and configuration.
Abbreviations used in this document
Fig. = Figure
D.S. = drive side
O.S. = operator’s side
PU = printing unit
LED = light-emitting diode
MID = press display
KID = compact display
UTK009560201001000000
UTK009560201000000000002

GR 009560000000000000
I.2
Topicality
The information provided in this manual corres-
ponds to the series version of the press at the time
of publication of this document. We reserve the
right to make changes in accordance with the pro-
gress of modern technology.
Should you have any questions, please contact
your Heidelberg agency.
Note on protection
Essential parts, devices and assemblies as well as
software, control and measuring devices of our
machines are internationally protected by copy-
right, patents and other intellectual property laws
and regulations.
Any form of disclosure or reproduction of this docu-
ment or exploitation and communication of its con-
tents are prohibited. Failure to meet these require-
ments may result in severe legal liability. All rights
reserved in case of patents granted or registered
utility models.
Copyright, address of manufacturer
ECopyright 2002 by
Heidelberger Druckmaschinen AG
Kurfürsten-Anlage 52 – 60
69115 Heidelberg
Germany
Printed in Germany
Fig. 2

Overall chapter overview
1
Table of Contents
A Safety A.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Safety A.1.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Testing the Preset Plus feeder protective devices with CP2000 A.1.2. . . . . . . . . . . . . . . .
3 Protective devices on the Preset Plus feeder A.1.4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Plus feeder control panels A.1.6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B Control B.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Adjustments for the Preset Plus feeder B.1.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Malfunctions – Preset Plus feeder B.1.12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C Machine C.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Feeder – To be observed when working at the press C.1.1. . . . . . . . . . . . . . . . . . . . . . . . . .
2 Pile change C.1.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Preloading and pile change C.1.9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Automatic pile alignment C.1.12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Suction head C.1.16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 Overview table – suction head settings for different printing materials C.1.22. . . . . . . . . . .
7 Sheet separator fingers C.1.25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 Adjusting blast air on the suction head C.1.27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 Pile stops C.1.31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 Ionizing unit C.1.33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 Lateral sheet separation blowers C.1.35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 Rope guide C.1.37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 Double sheet detector C.1.42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 Forwarding rollers C.1.48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 Pull lay C.1.49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 Separator rolls C.1.55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 Front lays C.1.58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 Crash bar C.1.62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 Replacing the suction tape C.1.63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 Adjustment information for special printing material C.1.74. . . . . . . . . . . . . . . . . . . . . . . . . . .
D General information / Checklists D.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General information D.1.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 General maintenance information D.1.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Notes on the maintenance schedule D.1.6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Overall chapter overview
2
3 Maintenance interval D.1.7.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Manual lubrication with grease D.1.9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Lubricants D.1.10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 Cleaners and washing fluids D.1.11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checklists D.2.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Note on the checklists D.2.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Check list, signature box D.2.4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Checklist for the Preset Plus feeder, SM 102/CD 102 D.2.5. . . . . . . . . . . . . . . . . . . . . . . . .
4 Checklist for the printing unit, SM 102/CD 102 with Preset Plus feeder D.2.8. . . . . . . . . .
Maintenance D.3.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Feeder – To be observed for all work D.3.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Service activities on the preloading device D.3.4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Service activities on the suction head D.3.5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Service activities on the compressed-air control unit D.3.9. . . . . . . . . . . . . . . . . . . . . . . . . .
5 Service activities on pile guide rail and pile transport D.3.11. . . . . . . . . . . . . . . . . . . . . . . . . .
6 Service activities on the feed table D.3.15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 Printing unit – To be observed for all work D.3.18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 Service activities on the sheet alignment system D.3.19. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E Index E.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Main chapter overview
A.1
A Safety
1 Safety A.1.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Important information about working safely on the Preset Plus feeder A.1.1. . . . . . . . . . .
2 Testing the Preset Plus feeder protective devices with CP2000 A.1.2. . . .
2.1 Testing the protective devices A.1.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Symbols of the protective devices A.1.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Protective devices on the Preset Plus feeder A.1.4. . . . . . . . . . . . . . . . . . . . .
3.1 Fixed guards A.1.4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Moveable guards A.1.4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Guards on the Preset Plus feeder A.1.4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Plus feeder control panels A.1.6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Plus feeder control panel A.1.6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Pile control control panel A.1.10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Suction head control panel A.1.11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4 Air control control panel A.1.12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Main chapter overview
A.2

Safety
confidential
A.1.1
1 Safety
1.1 Important information about working safely on the Preset Plus feeder
The operating manual of the Preset Plus feeder is an
applicable document of the operating manual you
have received together with the press. The safety
chapter of the operating manual contains important
information about working safely with the press.
DBefore you start up the Preset Plus feeder, read
this operating manual and the operating manual
you have received together with the press.
DMake sure that all persons working on this
press
Dhave received training and instructions,
Dhave read this operating manual,
Dhave read the operating manual of the
press,
Dfollow the regulations and instructions for
working without risk.
DKeep the operating manual so that it is always
available to the operators of the press.
UTKSG9011811000000000

GR SG9010170000003000
Safety confidential
A.1.2
2 Testing the Preset Plus feeder protective devices with CP2000
2.1 Testing the protective devices
Service / Safety
É
É
12345
Job
Name
É
É
ÉÉ
Safety
5
2
3
4
1
Fig. 1 Service/safety menu
The menu on the CP2000 Center shows the safety
devices of the press in a diagram. The representa-
tion may differ from the configuration of your press.
Prior to testing the protective devices, close all
guards and unlock all emergency stop buttons .
1. Press the Malfunction button (Fig. 1/1) in the
banner line. The Malfunction menu appears.
2. Press the Service button (Fig. 1/2). The Ser-
vice menu appears.
3. Press the
Safety button (Fig. 1/3). The Safety
menu (Fig. 1) appears.
A picture of the press now appears on the screen in
which all the safety devices that are to be checked
are shown in red.
4. Press and unlock the
emergency stop button .
5. Actuate the finger protecting bars.
6. One by one and in succession open and close
every guard, except for the test of the finger
protecting bars. If the respective guard is func-
tioning correctly, its symbol in the display goes
off.
UTKSG9011810000000000

GR SG9010171000001000
Safety
confidential
A.1.3
7. Press the
Return button to exit the menu.
If another symbol is still visible:
1. Locate the displayed guard and check it again.
2. Notify the service department of your
Heidelberg agency if the guard is defective.
Re-initialize the test:
1. Press the
Reset button (Fig. 1/5). The test is
initialized so that it can be repeated completely
(after an interruption, for example).
2.2 Symbols of the protective devices
Fig. 2 Feeder protective devices
Feeder
Emergency stop button
Bottom main pile limitation
Upper main pile limitation
Bottom auxiliary pile limitation
Upper auxiliary pile limitation
Upper pile safety
Suction head at highest position
The control flap on the suction head was
actuated.

GR SG901
1861000000000
Safety confidential
A.1.4
3 Protective devices on the Preset Plus feeder
3.1 Fixed guards
Warning – Risk of injury
Start up the press only when all
guards, coverings and parts of the
housing are mounted on the press.
The coverings of the side frames of the Preset Plus
feeder on D.S. and on O.S. are firmly screwed on.
Operate the press only when all guards, coverings
and parts of the housing are mounted on the press.
3.2 Moveable guards
The moveable (electrically interlocked) guards can
be opened by hand to carry out makeready and
maintenance work.
When you open an electrically protected guard while
production is running, the press stops immediately
with the exception of
Dthe ink fountain roller,
Dthe water pan roller and the metering roller in
the dampening system, if the dampening sys-
tem guard was not opened.
Dthe coating pan roller when the guard in front of
the coating pan roller and the metering roller
was not opened.
3.3 Guards on the Preset Plus feeder
1
2
Fig. 3
UTKSG9011809000000000

Safety
confidential
A.1.5
Fig. Moveable guards Inching mode with
travel limitation Inching mode without travel
limitation
Crawl speed mode
1 Glass sliding guard in front of the
feeder pile (noise protection) Yes Yes Yes
2Door on the feed table Yes – –
Tab. 1

GR SG901
1862000000000
GR SG901
1864000000000
Safety confidential
A.1.6
4 Plus feeder control panels
4.1 Plus feeder control panel
1000
h
Fig. 4 Feeder control panel
5
6
2
3
4
1
7
8
9
Fig. 5 Feeder control panel, detail
1
Blowing/suction nozzle
Increases the blast air volume of the blowing/
suction nozzle.
2– button
Reduces the blast air volume of the blowing/
suction nozzle.
3
Propelling roller
Increases the suction air volume of the propel-
ling roller.
4– button
Reduces the suction air volume of the propel-
ling roller.
5
Pull plate
Increases the suction air volume of the pull
plate.
6– button
Reduces the suction air volume of the pull
plate.
7
Suction tape
Increases the suction air volume of the suction
tape.
8– button
Reduces the suction air volume of the suction
tape.
9
Clearing the feed table
Transports all sheets that are on the feed table
up to the ratchet pawl.
UTKSG9011812000000000

GR SG901
1865000000000
Safety
confidential
A.1.7
1000
h
10
11
12
13
14
15 16
17
18
19
20
21
22
Fig. 6 Feeder control panel, detail
10 Press display
Displays the current press data (number of im-
pressions, degree value), monitoring of the feed
gripper, general malfunctions, etc.
11
Production
Press in operation: The press automatically
transitions to production mode.
If the press is not in operation: the start-up
warning sounds. If pressed again, the press
automatically goes into production mode.
Note
For presses with central air supply,
press the
Compressor button before-
hand.
12
Halt
Stops the press. Actuation during the produc-
tion run: switches off all functions for the pro-
duction run (except for the compressor).
Note
The
Halt button is not an Emergency
stop button
!
13
Increase print speed
Increases the press speed continuously.
14
Reduce printing speed
Reduces the press speed continuously.
15
Inch forward
The start-up warning signal sounds before the
press is inched forwards. Condition: The
Con-
trol panel selection
button on the feeder has
been pressed.
16
Select control panel
Press the button twice: From this control panel,
the press can only be moved in inching mode
(LED is ON).
To cancel the selection: Press the button again
(LED is OFF).
17 Operation
The start-up warning signal sounds.
The press starts up at minimum speed when
the button is actuated again.
18
Compressor
Switches the compressor ON (LED is ON) and
OFF.
19
Feeder ON
Switches the feeder automatically ON (LED is
ON) and OFF.
20 Dampening form rollers ON/OFF
Throws all preselects dampening form rollers
manually ON (LED is ON) or OFF.

GR SG901
1866000000000
Safety confidential
A.1.8
21
Paper ON
Switches the sheet travel ON (LED is ON) and
OFF.
22
EMERGENCY ST OP
The press stops immediately and the palm but-
ton is locked.
Turn: the lock is released.
23
2925 27
26
24
28 30
31
Fig. 7 Feeder control panel, detail
23
Malfunction button red
Due to a fault, the press cannot be put into op-
eration.
24
Malfunction button blue
Due to a fault, the press cannot be put into op-
eration.
25
Pull distance correction towards D.S.
26 Pull distance correction towards O.S.
Note
The feeder display shows the current
format width during adjustment or
when the
Pull distance correction but-
tons (Fig. 7/25 and 26) are pressed at
the same time.
27
Increase lateral sheet separation blower sheet
size
Moves the opposite lateral sheet separation
blower away from the pile. The lateral sheet
separation blower on the pull side remains.
28
Reduce lateral sheet separation blower sheet
size
Moves the opposite lateral sheet separation
blower towards the pile. The lateral sheet sepa-
ration blower on the pull side remains.
Note
The feeder display shows the current
format width during adjustment or
when the
Lateral sheet separation
blower sheet size
buttons (Fig. 7/27
and 28) are pressed at the same time.
29 Pile to D.S.
Moves the active pile to D.S.
30
Pile to O.S.
Moves the active pile to O.S.
31
Pile alignment automatic ON/OFF
Selects the pile alignment operating mode.
The LED is ON: ”Automatic”
The LED is OFF: ”Manual” mode

GR SG901
1867000000000
Safety
confidential
A.1.9
34
3532
3633
37
38
Fig. 8 Feeder control panel, detail
32
Suction head up
Automatic mode: Increases the nominal value
of the height adjustment.
Manual mode: Moves the suction head up.
33
Suction head down
Automatic mode: Decreases the nominal value
of the height adjustment.
Manual mode: Moves the suction head down.
Caution – Danger of collision!
The suction head can collide with the
pile when it is moved down. Lower the
pile before you move the suction head
downwards.
34
Height adjustment automatic ON/OFF
Selects the height adjustment operating mode.
The LED is ON: ”Automatic”
The LED is OFF: ”Manual” mode
35
Increase suction head sheet size
Moves the suction head away from the forward-
ing rollers.
36 Reduce suction head sheet size
Moves the suction head in the direction of the
forwarding rollers.
37
Increase blast air compensation
Increases the blast air volume of the blast air
compensation.
38
Reduce blast air compensation
Reduces the blast air volume of the blast air
compensation.

GR SG9015883000000000
Safety confidential
A.1.10
4.2 Pile control control panel
5
6
7
2
3
4
1
Fig. 9 Pile control control panel
1
Auxiliary pile up
The auxiliary pile moves upwards as long as
the button is pressed.
2
Auxiliary pile down
The auxiliary pile moves down as long as the
button is pressed.
3 Main pile up
The main pile moves upwards as long as the
button is pressed.
4 Main pile down
Moves the main pile down. The downward
movement stops approximately 12 cm above
the ground. Pressing the button again briefly
moves the pile support plate down to a distance
of approximately 1 cm above the floor. Pile sup-
port plate and pile support frame are centered
and set down to the floor.
5
Pile stop
Interrupts the movement of auxiliary pile and
main pile.
6
Pile to D.S.
”Manual” mode: Moves the active pile to D.S.
7
Pile to O.S.
”Manual” mode: Moves the active pile to O.S.

GR SG901
1863000000000
Safety
confidential
A.1.11
4.3 Suction head control panel
3
11
12
9
10
81
4 5 6
7
2
Fig. 10 Suction head control panel
1
Forwarding sucker O.S.
Adjusts the level of the forwarding sucker on
O.S.
2
Lifting sucker inclination
Adjusts the inclination of the lifting suckers.
3
Rear edge blowers
Adjusts the blast air volume of the rear edge
blowers.
4
Inner carrier air blowers
Adjusts the blast air volume of the inner carrier
air blowers.
5
Outer carrier air blowers
Adjusts the blast air volume of the outer carrier
air blowers.
6 Sheet separation blowers
Adjusts the blast air volume of the sheet sepa-
ration blowers.
7 Lifting sucker distance
Adjusts the magnitude of the stroke movement.
8
Forwarding sucker D.S.
Adjusts the level of the forwarding sucker D.S.
9
Suction head up
Automatic mode: Increases the nominal value
of the height adjustment.
Manual mode: Moves the suction head up.
10
Suction head down
Automatic mode: Decreases the nominal value
of the height adjustment.
Manual mode: Moves the suction head down.
Caution – Danger of collision!
The suction head can collide with the
pile when it is moved down. Lower the
pile before you move the suction head
downwards.
11
Increase blast air compensation
Increases the blast air volume of the blast air
compensation.
12
Reduce blast air compensation
Reduces the blast air volume of the blast air
compensation.

GR SG9015877000000000
Safety confidential
A.1.12
4.4 Air control control panel
2 4
1 3 5
6
Fig. 11 Air control control panel
1
Corner blowers D.S.
Adjusts the blast air volume of the corner blow-
ers D.S.
2
Corner blowers O.S.
Adjusts the blast air volume of the corner blow-
ers O.S.
3 Diagonal blower bars D.S.
Adjusts the blast air volume of the diagonal
blower bars D.S.
4 Diagonal blower bars O.S.
Adjusts the blast air volume of the diagonal
blower bars O.S.
5
Guide plate
Adjusts the level of the guide plate.
6
Pre-separation air
Adjusts the pre-separation air volume of the
carrier air blowers and sheet separation blow-
ers. The pre-separation air is blown into the pile
before the sheet travel is switched on.

Main chapter overview
B.1
B Control
1 Adjustments for the Preset Plus feeder B.1.1. . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Print job preparation B.1.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Sheet travel/Feeder pile menu B.1.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Air adjustment B.1.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 Selecting cardboard mode for the separator roll bar B.1.5. . . . . . . . . . . . . . . . . . . . . . . . . .
1.5 Changing the cover guide height later B.1.6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6 Adjusting the front lay deflection B.1.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7 Switching automatic pull lay cleaning on/off B.1.8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8 Switching the double sheet detector in the pull lay on or off (option) B.1.9. . . . . . . . . . . .
1.9 Switching the ultrasonic double sheet detector on/off (option) B.1.10. . . . . . . . . . . . . . . . . .
2 Malfunctions – Preset Plus feeder B.1.12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Malfunctions in the pile height sensor B.1.12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Bundle detector B.1.13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Tear-off detector / multiple-sheet detector B.1.14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Main chapter overview
B.2