Helion four 10 tr User manual

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
Quick-Start
Guide
Product specications are subject to change without notice.
Due to ongoing development, the actual product may vary from
images shown.
This product contains chemicals known to the State of California
to cause cancer, birth defects and other reproductive harm.
This product is not a toy! (14+) Recommended for ages 14 and
up. Adult supervision required for ages under 18 years old.
Contains small parts, keep out of reach of children 3 years of
age and younger.
To download the full Owner’s Manual &
Technical Information Guide, please visit
www.Helion-RC.com or scan the QR code
with your smart phone.
Distributed in the
UK by:
J Perkins Distribution Ltd,
Lenham,
Kent, UK
ME17 2DL.
www.jperkins.com
Distributed in Australia by:
Model Engines (Aust.) Pty. Ltd.,
Unit 1, 158-168 Browns Road,
Noble Park,
Victoria,
3174,
Australia.
www.modelengines.com.au
Ph [phone]
[email protected]
Distributed in the US by:
Firelands Customer Service/Product Support
1133 Libra Drive, Lincoln, NE 68512
www.relandsgroup.com
1-800-205-6773
customerservice@relandsgroup.com
Quick Start applies to:
HLNS1200
MADE IN CHINA

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
Locate the wheelie bar and, using
a 2mm and 2.5mm hex driver,
secure it as shown with two M3
x 15mm and two M4 x 15mm
dome, hex head, machine screws.
1Remove the components from
the box and ensure the contents
are correct:
• 1x Four 10TR 4WD truggy
• 1x IKONNIK ET4 2.4GHz
4-channel transmitter
• 1x wheelie bar
• 1x rear spoiler
• 1x screw set
• 1x Quick-Start Guide
2To complete the nal assembly of
your Four 10TR you will need the
following items:
• 1x 2-4S LiPo battery*
• 1x Suitable LiPo battery
charger
• 1x 2mm hex driver
• 1x 2.5mm hex driver
• 4x AA batteries.
3Peel the protective wrapping
from your car, remove all four
body clips, the body itself and the
protective netting.
4
*ensure battery ts in truck if purchasing new

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
5Locate the spoiler and, using
a 2mm hex driver secure it as
shown using two M3 x 10mm
dome, button head, machine
screws and countersunk plastic
washers.
6Fully charge your chosen Li-Po
battery in accordance with charging
and safety guidelines supplied with
the product. Note that the battery
must have a compatible High
Current T-plug. Also, note that if
using a NiMH battery, you will need
to reset the Low-Voltage Cut-Off on
your ESC to suit.
7Locate the battery cradle on the
left side of the car, insert the fully
charged LiPo into the cradle and
tighten the hook and loop straps
to secure it rmly in position.
8Plug the two pin headlight lead
into the channel 3 receiver socket
noting the polarity, i.e. black lead
closest to the edge of the receiver
case.
9Remove the transmitter battery
cover and insert four AA alkaline
cells.
We recommend starting with a 2S Li-Po then
moving up to 3S and eventually 4S if desired.

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
10 Ensure the radio switch is in the
off position, then connect the
battery to the ESC.
11 Reinstall the protective netting,
then replace the body and secure
it with the four body clips.
12 Switch ON your ET4 transmitter and
ensure that the LED is lit solid red
and that no alarms are audible.
And conrm beginner mode setting
is as desired.
13 Locate the switch and turn
ON your Four 10TR. In the
unlikely event that the car does
not operate, see the PAIRING
instructions at the back of this
guide.
14 Check the operation of the throttle
and steering. Pulling the throttle
trigger back will drive the car
forwards. Pushing the trigger
forwards will apply the brakes or
drive the car in reverse. Turning
the wheel right will cause the car
to turn right and vice versa.
15 Use the throttle and steering trim
buttons to ne tune the controls
of your car. Double check that the
Four 10TR tracks in a straight line
and doesn’t creep forwards or
backwards at zero throttle.

QUICK-START GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
PAIRING/BINDING GUIDE
1Place your Four 10TR and ET4
transmitter in close proximity but
not less than 12” (300mm) apart.
2Switch ON your ET4 transmitter.
Switch ON your Four 10TR. The
receiver’s LED will blink.
3Switch OFF your ET4 transmitter,
hold down the REV/PAIR button
and switch the transmitter ON
once again.
4Press the Pair button on the
receiver. The LED will blink.
Release the Pair button.
5When the LED on the receiver
shows solid red your ET4 and Four
10TR will be paired. Return to
Step 13 of this guide to complete
the set-up of your car.
Having followed steps 1 to 13, in the unlikely event that your car does not operate please
follow the 6 stage pairing/binding process detailed here.
300mm
Minimum

PAIRING /BINDING GUIDE
Full manual available to download from: www.Helion-RC.comFull manual available to download from: www.Helion-RC.com
NOTE: If you experience any problems,
please consult online troubleshooting guide. 000632-002 (REV A)