Hella marine Sea Hawk-XLB User manual

Light Source LED
Light Output ~2200 lumens (white)
Colour Temperature 5000K (white)
Operating Voltage MultivoltTM 9-33V DC
Power Consumption High 25W (2A @ 12V / 1A @ 24V)
Low 5W (not applicable to pencil beam lamp models)
Housing Material 'Non-metal' thermally conductive housing
Lens Material Heavy duty Grilamid®
Cable Pre-wired with tinned marine cable
Degree of Protection IP 6K7 IP6K9K (Completely sealed)
Weight 580g (including cable)
Manufacturing Location New Zealand
Electrical Protection This lamp is protected against overvoltage, voltage spikes, reverse polarity
connection and negative voltage spikes.
Electromagnetic Compatibility (EMC)
This LED lamp is an electronic device. The electrical circuits contain components that suppress possible interference, both
emission as well as susceptibility, to the limits prescribed in international regulations.
Wiring and High / Low mode activation
The lamp defaults to High mode when positive (red) and negative (black) cables are connected.
To activate Low mode, connect blue cable to positive and the black cable to negative.
Switching between Low and High modes can be achieved using any regular ON / OFF / ON switch.
*Low mode not available on pencil beam lamp models
LED modules are polarity conscious. Reverse polarity will not damage this product but will inhibit its function. HELLA recommends
wire connections be soldered, and heat shrink tubing applied to seal the joint. Each lamp must be protected by a fuse rated at
5 amperes maximum.
Hella marine LED products offer many advantages over conventional bulb lamps. Signicantly reduced power consumption, ultra
long life and high tolerance to shock and vibration make HELLA LED lamps the ideal choice for the harsh marine environment.
www.hellamarine.com
Sea Hawk-XLB LED Deck Floodlight
Cable
colour Connect to Consumption
Red Positive (+) 25 watts
Black Negative (-)
Blue* Low mode (+) 5 watts
958 315-33 (ENG) V03
Tinned cable
+ve Red = High (25W)
+ve Blue* = Low (5W)
-ve Black
30º
20º
d
d
a
a
b
c
Dimensions:
a = 350mm / 13.78”
b = 56mm / 2.20”
c = 81mm / 3.19”
d = min. 200mm / 7.87”
max. 280mm / 11.02”
Light Source LED
Light Output ~2200 lumens (white)
Colour Temperature 5000K (white)
Operating Voltage MultivoltTM 9-33V DC
Power Consumption High 25W (2A @ 12V / 1A @ 24V)
Low 5W (not applicable to pencil beam lamp models)
Housing Material 'Non-metal' thermally conductive housing
Lens Material Heavy duty Grilamid®
Cable Pre-wired with tinned marine cable
Degree of Protection IP 6K7 IP6K9K (Completely sealed)
Weight 580g (including cable)
Manufacturing Location New Zealand
Electrical Protection This lamp is protected against overvoltage, voltage spikes, reverse polarity
connection and negative voltage spikes.
Electromagnetic Compatibility (EMC)
This LED lamp is an electronic device. The electrical circuits contain components that suppress possible interference, both
emission as well as susceptibility, to the limits prescribed in international regulations.
Wiring and High / Low mode activation
The lamp defaults to High mode when positive (red) and negative (black) cables are connected.
To activate Low mode, connect blue cable to positive and the black cable to negative.
Switching between Low and High modes can be achieved using any regular ON / OFF / ON switch.
*Low mode not available on pencil beam lamp models
LED modules are polarity conscious. Reverse polarity will not damage this product but will inhibit its function. HELLA recommends
wire connections be soldered, and heat shrink tubing applied to seal the joint. Each lamp must be protected by a fuse rated at
5 amperes maximum.
Hella marine LED products offer many advantages over conventional bulb lamps. Signicantly reduced power consumption, ultra
long life and high tolerance to shock and vibration make HELLA LED lamps the ideal choice for the harsh marine environment.
www.hellamarine.com
Sea Hawk-XLB LED Deck Floodlight
Cable
colour Connect to Consumption
Red Positive (+) 25 watts
Black Negative (-)
Blue* Low mode (+) 5 watts
958 315-33 (ENG) V03
Tinned cable
+ve Red = High (25W)
+ve Blue* = Low (5W)
-ve Black
30º
20º
d
d
a
a
b
c
Dimensions:
a = 350mm / 13.78”
b = 56mm / 2.20”
c = 81mm / 3.19”
d = min. 200mm / 7.87”
max. 280mm / 11.02”

Warranty
ENGLISH
Congratulations! The product you have selected comes from HELLA – one of the world's leading manufacturers of lighting
products. The product comes with a 5 year warranty from end user purchase covering faults in materials, components or
workmanship.
In the unlikely event that you should experience a conrmed warranty related problem with your purchase, HELLA will, at its discretion,
either repair, replace or refund the purchase price of the product. Warranty services may be obtained by returning the product within the
warranty period to the HELLA dealer where the product was originally purchased.
This warranty is in addition to and does not preclude any other rights or remedies available to the consumer under any local legislation
related to the provision of goods or services.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty does not cover:
1. Claim/s as a result of normal wear and tear or of any modications and / or alterations to the product in any shape or form.
2. Claim/s as a result of non-compliance of the assembly, service and operating instructions and/or any unt or improper use.
3. Any expenses incurred in the process of making the claim.
Note: For lamps sold in Australia warranty services are provided by: Hella Australia Pty Ltd, 54-76 Southern Rd, Mentone VIC 3194
Customer Service 1800 061 729 www.hella.com/hella-au/21.html
For general comments about Hella marine products please email [email protected]
1
2
CLICK
2
3
min. 47 mm
max. 280mm
min. 200mm
5 mm
Ø7 mm
Ø7 mm
Tip:
When assembling bracket (2) push
grey barbed insert (3) up slightly while
gently pushing the outer bracket pieces
together.
This will enable barbed insert to seat
correctly into outer brackets and lock
down when tightened.
Note:
Supplied M6 Hex Socket Capscrews
are suitable for mounting onto <18mm
thick structures. If longer fastenings are
required ensure 316 stainless steel Hex
Socket Capscrews are used.
Brackets are designed to be mounted
onto at surfaces.
Warranty
ENGLISH
Congratulations! The product you have selected comes from HELLA – one of the world's leading manufacturers of lighting
products. The product comes with a 5 year warranty from end user purchase covering faults in materials, components or
workmanship.
In the unlikely event that you should experience a conrmed warranty related problem with your purchase, HELLA will, at its discretion,
either repair, replace or refund the purchase price of the product. Warranty services may be obtained by returning the product within the
warranty period to the HELLA dealer where the product was originally purchased.
This warranty is in addition to and does not preclude any other rights or remedies available to the consumer under any local legislation
related to the provision of goods or services.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty does not cover:
1. Claim/s as a result of normal wear and tear or of any modications and / or alterations to the product in any shape or form.
2. Claim/s as a result of non-compliance of the assembly, service and operating instructions and/or any unt or improper use.
3. Any expenses incurred in the process of making the claim.
Note: For lamps sold in Australia warranty services are provided by: Hella Australia Pty Ltd, 54-76 Southern Rd, Mentone VIC 3194
Customer Service 1800 061 729 www.hella.com/hella-au/21.html
For general comments about Hella marine products please email [email protected]
1
2
CLICK
2
3
min. 47 mm
max. 280mm
min. 200mm
5 mm
Ø7 mm
Ø7 mm
Tip:
When assembling bracket (2) push
grey barbed insert (3) up slightly while
gently pushing the outer bracket pieces
together.
This will enable barbed insert to seat
correctly into outer brackets and lock
down when tightened.
Note:
Supplied M6 Hex Socket Capscrews
are suitable for mounting onto <18mm
thick structures. If longer fastenings are
required ensure 316 stainless steel Hex
Socket Capscrews are used.
Brackets are designed to be mounted
onto at surfaces.