Helo LAINE STJ User manual

ELECTRIC SAUNA HEATER
0418 –6 –171809
0418 –8 –171809
0418 –9 –171809
314 SKDT 1-3 A
Product Manual Laine STJ
The genuine Finnish sauna

Contents
1. Manual for sauna heater 3
1.1 Check before taking a sauna bath 3
1.2 Operation of the sauna heater controls 3
1.3 Infromation for use 3
1.4 Sauna room 3
2. Recommended sauna room ventilation 4
2.1 Heating the sauna 4
2.2 Sauna heater stones 5
2.3 Sauna heater controls 6
2.3.1 Timer switch 6
2.3.2 Thermostat 6
2.4 Electric heating toggle 6
2.5 If the sauna heater will not heat up 6
2.6 Preparing for sauna heater installation 7
2.7 Installation 7
2.8 Main connection 8
2.9 Electric heating toggle 9
2.10 Location the connection box for connection cable in 9
the sauna room 9
2.11 Wiring diagram 10
3. Spare parts for Laine STJ 11
4. ROHS 11
Instructions for environmental protection 11
Images and table
Image 1 Sauna room ventilation 4
Image 2 Safety clearances distances, minimum dimensions (mm) 7
Image 3 Location for the connection box 9
Image 4 Switch diagram for the sauna heater 10
Table 1 Safety clearances distances, minimum dimensions (mm) 8
Table 2 Connection cable and fuse 8
Table 3. Spare parts for Laine STJ 11
Product Manual Laine STJ
2

1. Manual for sauna heater
1.1 Check before taking a sauna bath
1. The sauna room is suitable for taking a sauna bath.
2. The door and the window are closed.
3. The sauna heater is topped with stones that comply with the manufacturer's
recommendations, the heating elements are covered with stones, and the stones are
piled sparsely.
NOTE: Structural clay tiles are not allowed.
1.2 Operation of the sauna heater controls
The main switch of the sauna heater is located in the lower part of the sauna heater, beside the ther-
mostat.
Set the heater's thermostat to the desired temperature. You can find the ideal temperature for taking a
sauna bath by first turning the thermostat to the maximum. Once the sauna room is warm enough,
simply turn the thermostat control backwards, i.e. counter-clockwise, until the heating elements turn
off (you can hear a clicking sound). You can fine-tune the temperature by slightly turning the thermo-
stat knob in either direction.
The sauna heater operates with a 12-hour timer.
The timer is operated by turning the timer knob clockwise from the 0 position.
In the 0 position, the power is off and the sauna heater is not on.
In the 0–3 hour zone, heating elements will turn on and the sauna heater is warm for the selected
period of time.
In the 1–9 hours zone, you can preset the time after which the sauna heater will turn on. For example,
by turning the knob at 6, the sauna heater will turn on after six hours and stay warm for three hours
unless the timer is turned to the 0 position earlier.
Pleasant, smooth sauna bath temperature is about 70 °C.
Rearrange the sauna stones at least once a year and replace any weathered stones. This enhances
air circulation between the stones, which extends the useful life of the thermal resistors.
If you encounter any problems, please contact the manufacturer's warranty service shop. A list of war-
ranty service shops is included in the delivery.
For additional information about enjoying a sauna bath, please visit our website at:
www.sauna360.com
1.3 Infromation for use
This appliance may not be used by children aged less than eight years, by persons with reduced
physical, sensory or mental capabilities, or by persons lacking experience and knowledge regarding
its operation only if such have been given instructions on the safe use of the device and the risks in-
volved. Children must not be allowed to play with the appliance or to clean and service it without su-
pervision. (7.12 EN 60335-1:2012)
1.4 Sauna room
The walls and ceiling of a sauna room should be thermally well insulated. All surfaces that store heat,
such as tiled and stone surfaces must be insulated. It is recommended to use wooden panel cladding
inside the sauna room. If there are heat storing elements in the sauna room, such as decorative
stone, glass etc., note that these elements may extend the pre-heating period even though the sauna
room is otherwise well insulated (see page 7, section 2,6 Preparing ).
Product Manual Laine STJ
3

2. Recommended sauna room ventilation
Image 1 Sauna room ventilation
1. Sauna room 3. Electric sauna heater 5. Exhaust flue or channel
2. Washroom 4. Exhaust valve 6. Door to the sauna room
7. A ventilation valve can be installed here to be kept closed while the sauna is heated and during bathing.
Inlet vent can be positioned in the A zone. Make sure the incoming fresh air will not interfere with (i.e. cool down) the sauna
heater's thermostat near the ceiling.
The B zone serves as the incoming air zone, if the sauna room isn't fitted with forced ventilation. In this case, the exhaust
valve is installed min 1m higher than the inlet valve.
DO NOT ISTALL INLET VALVE WITHIN ZONE C, IF THE SAUNA HEATER'S CONTROL THERMOSTAT IS LOCATED AT
THE SAME ZONE.
2.1 Heating the sauna
Before turning the sauna heater on, make sure the sauna room is suitable for taking a sauna bath. When heated for the first
time, the sauna heater may emit some odour. If you detect any odour while the sauna heater warms up, disconnect the
sauna heater briefly, and air the room. Then turn the sauna heater back on.
The sauna heater is turned on by twisting the timer knob, and the temperature is adjusted from the thermostat knob.
You should turn the sauna heater on roughly an hour before you plan to take a sauna bath, so that the stones have time to
heat up properly and the air warms up evenly in the sauna room.
Do not put any objects on the sauna heater. Do not dry clothes on the sauna heater or anywhere in its vicinity.
Product Manual Laine STJ
4
55
4
4
2
1
1
1
A
7
A
min
500 mm
6
3
B
3
B
C
C
C
C A
1000 mm

2.2 Sauna heater stones
Quality stones meet the following requirements:
-Sauna stones should withstand heat and heat variation caused by vaporisation of the water thrown on the
stones.
- Stones should be rinsed before use in order to avoid odour and dust.
- Sauna stones should have an uneven surface to supply a larger surface for the water to evaporate from.
- Sauna stones should be large enough, over 100 mm to allow good ventilation between the stones. This extends
the useful life of the heating elements.
- Sauna stones should be piled sparsely in order to enhance ventilation between the stones. Do not bend the
heating elements together or against the frame.
- Rearrange the stones regularly (at least once a year) and replace small and broken stones with new, larger
stones.
- Stones are piled so that they cover the heating elements. Do not, however, pile a large heap of stones on the
heating elements. For a sufficient amount of stones refer to Table 1 on page 8. Any small stones in the package
of stones must not be piled on the sauna heater.
- The warranty does not cover defects resulting from poor ventilation caused by small and tightly packed stones.
-Structural clay tiles are not allowed. They may cause damage to the sauna heater that will not be covered
by the warranty.
- Do not use soapstone as sauna rocks. Any damages resulting from this will not be covered by the stove
warranty.
- Do not use lava stone as sauna rocks. Any damages resulting from this will not be covered by the stove
warranty.
-DO NOT USE THE HEATER WITHOUT STONES.
Product Manual Laine STJ
5

2.3 Sauna heater controls
2.3.1 Timer switch
The sauna heater is controlled by operating a 12-hour timer with three operating zones. The timer is set by twisting the knob
clockwise until the desired operating zone is reached. When operating, the timer gradually travels counter-clockwise towards
the zero position.
1. 0 position. The sauna heater is not on.
2. Operating zone 1–3 hours. Set on this zone, the sauna
heater heats up at full power while the sauna thermostat
controls the temperature.
3. Preset zone 1–9 hours. Set on this zone, the sauna heater
can be preset to turn on after a certain period of time. The
heating elements will not heat up when the timer is within
this zone.
Before turning the sauna heater on, make sure the sauna room
is suitable for taking a sauna bath.
The timer operates better if it is first turned further than the desired time
and then turned back to the desired time. If the switch has not travelled
back to 0 position after finishing bathing, turn it to 0 manually.
2.3.2 Thermostat
The thermostat knob is next to the timer knob. The further
right (clockwise) the timer is switched, the higher the
temperature will rise in the sauna room. The best way to find
the ideal temperature is to first turn the thermostat fully on
the right and let the temperature rise to the desired temperature.
Subsequently, turn the thermostat knob slowly counter-clockwise
until you hear a gentle clicking sound. If you want to readjust the
temperature, turn the thermostat gradually until the temperature
is ideal.
The thermostat will not operate correctly if the stones are piled too
densely or they are too small. Please refer to section ”Sauna heater
stones” on page 5
The thermostat has an integrated temperature limiter with a reset switch
next to the thermostat knob.
2.4 Electric heating toggle
Electric heating toggle applies to homes with an electric heating system.
The sauna heater thermostat also controls the heating toggle. In other words, home heating turns on once the sauna ther-
mostat cuts power off the sauna heater.
2.5 If the sauna heater will not heat up
If the sauna heater will not heat up, please check that:
1. The power is on;
2. The timer is on the heating zone (operating zone);
3. The thermostat is switched to a temperature that is higher than the current temperature of the sauna room;
4. The front fuses of the sauna heater are intact;
5. The timer is not stuck. Make sure the knob doesn't chafe against the base; there should be min 1mm gap between the
knob and the base.
If the sauna heater has been exposed to freezing conditions, the temperature limiter may have gone off. The limiter is reset
by pressing the reset switch. Note that the limiter does not work until the temperature has risen to approx. -5°C. If the sauna
heater still fails to work, please contact an authorised service for repair.
THE PERSON INSTALLING THE SAUNA HEATER SHOULD LEAVE THESE INSTRUCTIONS TO THE PREMISES FOR
THE FUTURE USER.
Product Manual Laine STJ
6

2.6 Preparing for sauna heater installation
Check the following before installing the sauna heater:
1. The ratio of the heater's input (kW) and the sauna room's volume (m3). Volume/input recommendations are
presented in Table 1 on page 8. The minimum and maximum volumes must not be exceeded.
2. The sauna room ceiling must be min 1900 mm high.
3. Uninsulated and masonry stone walls extend the preheating time. Each square metre of plastered ceiling or
wall surface adds 1.2 m3to the sauna room's volume.
4. Check page 8 table 2 section for a suitable fuse size (A) and the correct diameter of the power supply
cable (mm²) for the sauna heater in question.
5. Conform to the specified safety clearance around the sauna heater.
There should be enough room around the sauna heater for maintenance purposes, a doorway etc.
2.7 Installation
Image 2 Safety clearances distances, minimum dimensions (mm)
Follow the safety clearance specifications on page 8 when installing the sauna heater.
The sauna heater is a floor-standing model. The base must be solid, because the sauna heater weighs about 75 kg
with stones
The sauna heater is levelled by the adjustable legs.
The sauna heater needs to be fixed directly onto the wall or to the sauna bench module by using the provided metal
rack to make sure the safety distances will be maintained in use.
Walls or ceilings must not be clad with fibre-reinforced plaster board or other light-weight cladding, because they may
cause a fire hazard.
Only a single sauna heater is allowed per sauna room.
Product Manual Laine STJ
7
The sauna heater is attached mainly to the wall or In central installation to the boards with the lower
mounting holes for the sauna heater or to the floor using the floor brackets supplied. Diameter of drill bit
for wall mount Ø3.5 mm. Lid screw 6 x 40 mm (2 pcs.).
Min. mm Min. mm
2 x ( mm)6 x 40
330
A
A
D
75 230
75 230 D
860
1040
1900
H
6 x 40mm

Table 1 Safety clearances distances, minimum dimensions (mm)
2.8 Main connection
The sauna heater must be connected to the mains by a qualified electrician and in compliance with current regulations. Sau-
na heater is connected with a semi-permanent connection. Use H07RN-F (60245 IEC 66) cables or a corresponding type.
Other output cables (signal lamp, electric heating toggle) must also adhere to these recommendations. Do not use PVC
insulated cable as a connection cable for the sauna heater.
A multipolar (e.g. 7-pole) cable is allowed, if the voltage is the same. In the absence of a separate control current fuse, the
diameter of all cables must be the same, i.e. in accordance with the front fuse.
The connecting box on the sauna wall should be located within the minimum safety clearance specified for the sauna heater.
The maximum height for the connection box is 500mm from the floor.
If the connection box is located at 500mm distance from the heater, the maximum height is 1000mm from the floor.
Sauna heater insulation resistance:
The sauna heater heating elements may absorb moisture from air, e.g. during storage. This may cause bleeder currents.
The moisture will be gone after a few heating sessions. Do not connect the heater power supply through a ground fault inter-
rupter.
However, always adhere to the effective electrical safety regulation when installing the sauna heater.
Effect
kW
Heater connec-
tion cable
H07RN-F/
60245 IEC 66
mm2
400V –415V 3N~
Fuse
A
Heater connec-
tion cable
H07RN-F/
60245 IEC 66
mm2
230V 3~
Fuse
A
Heater connection
cable H07RN-F/
60245 IEC 66
mm2
230V –240V 1N~ / 2~
Fuse
A
6,0
8,0
9,0
5 x 1,5
5 x 2,5
5 x 2,5
3 x 10
3 x 16
3 x 16
4 x 2,5
4 x 6
4 x 6
3 x 16
3 x 25
3 x 25
3 x 10
3 x 10
-------
1 x 35
1 x 35
-------
Table 2 Connection cable and fuse
Power
Saunaroom
Minimum distance to
Stone
kW
Volume
m³
Side wall
A
mm
In front of
D
mm
Back surface
mm
Approx.
kg
6,0
8,0
9,0
5 –9
8 –12
9 - 13
60
80
100
100
120
150
75
75
75
62
62
62
Product Manual Laine STJ
8

2.9 Electric heating toggle
Electric heating toggle applies to homes with an electric heating system.
Sauna heater has connections (marked N - 55) for controlling the electric heating toggle. Connectors N - 55 and the heating
elements are simultaneously live (230V). The sauna heater thermostat also controls the heating toggle. In other words,
home heating turns on once the sauna thermostat cuts power off the sauna heater.
200 mm
A A
500 mm
3.
2.
500 mm
1
3.
2.
Image 3 Location for the connection box
2.10 Location the connection box for connection cable in
the sauna room
A = Specified minimum safety clearance
1. Recommended location for the connection box
2. Silumin box recommended in this area.
3. This area should be avoided. Always use a silumin box.
In other areas, use a heat-resisting box (T 125 °C) and heat-resisting cables (T 170 °C). The connection box
must be clear of obstacles. When installing the connection box to zones 2 or 3, refer to the instructions and
regulations of the local energy supplier.
Product Manual Laine STJ
9

2.11 Wiring diagram
1
2
3
kW
230V
SEPC 242 SEPC 243 SEPC 244
2000W 2670W 3000W
6,0
8,0
9,0
13
N N 55
B1 B2 B3
A1 A2 A3
354 SK ADT 1
1. 2. 3.
1,2,3 1,2,3
1 2 3 6 4 5
230 V 3~
kW - 9,0 kW6,0
L1 L2 L3
N
1 2 3 64 5
N /L1 L2
1 2 3 6 4 5
400V - 415V 3N~
kW - 9,0kW6,0
L1 L2 L3
230V - 240V 1N~/ 2~
kW- 8,0 kW6,0
13
13 46 46 46
1,2,3
1. Syöttö / Nätet / Stromnetz / Power input. / Puissance absorbée / Vermogensingang / Entrada de
alimentación / Входное напряжение / Wejście zasilania.
2. Merkkilamppu / Signallampa / Signal lamp / Kontrolleuchte / lampe de signal / lámpara de /
сигнальная лампа / lampa sygnalizacyjna
3. Sähkölämmityksen vuorottelu /Alternering med elvärme / Signal kontakt / Signal contact / Contact
du signal / Signaalcontact / Contacto señal /сигнала контакт / Sterowanie ogrzewaniem elektrycznym
Teho, Effekt
Input, Potencia
Leistung, Moc
Vöimsus,Wejscie
Puissance
Lämpövastukset, Värmeelement, Tennid, Heating elements,
Heizeelement, Resistores Térmicos, Éléments chauffants,
Elementy grzewcze,ТЭНы
Image 4 Wiring diagram for the sauna heater
Product Manual Laine STJ
10

3. Spare parts for Laine STJ
Parts
Product
number
Product title
Laine 6 STJ
Laine 8 STJ
Laine 9 STJ
1
SP5509053
Clock
OYKF 1
1
1
1
2
SP4321015
Thermostat
OLHC 2
1
1
1
3
SP7812550
Mains connector
NLWD 1-1
1
1
1
4
SP7712000
Cable clamp
NKWA 1
1
1
1
5
SP7309531
Knob
YWWA 6-1
2
2
2
6
SP5200731
Heater element
SEPC 242
2000W/230V
3
7
SP5200732
Heater element
SEPC 243
2670W/230V
3
8
SP5200733
Heater element
SEPC 244
3000W/230V
3
9
SP7513002
Screw
M5 x 10
3
3
3
Table 3. Spare parts for Laine STJ
4. ROHS
Product Manual Laine STJ
11
Instructions for environmental protection
This product must not be disposed with
normal household waste at the end of
its life cycle. Instead, it should be
delivered to a collecting place for the recycling
of electrical and electronic devices.
The symbol on the product, the instruction manual or the
package refers to this.
The materials can be recycled according to the
markings on them. By reusing, utilising the
materials or by otherwise reusing
old equipment, you make an important
contribution for the protection of our environment.
Please note that the product is returned to the recycling centre
without any sauna rocks and soapstone cover.
Please contact the municipal administration
with enquiries concerning the recycling place.