Henny Penny LOV LVG-102 User manual

Model LVG-102, 103, 104
1
TECHNICAL MANUAL
Henny Penny
Split Vat & Full Vat
Open Fryers – Gas
Model LVG-102
Model LVG-103
Model LVG-104

Model LVG-102, 103, 104
2

Model LVG-102, 103, 104
i
TABLE OF CONTENTS
Section Page
Section 1. TROUBLESHOOTING.............................................................................................. 1-1
1-1 Introduction .................................................................................................... 1-1
1-2 Safety.............................................................................................................. 1-1
1-3 Troubleshooting.............................................................................................. 1-2
1-4 Error Code Table ............................................................................................ 1-7
Section 2. INFO, FILTER & TEMP BUTTON STATS ............................................................... 2-1
2-1 INFO Button Stats.......................................................................................... 2-1
2-2 FILTER Button Stats ...................................................................................... 2-1
2-3 TEMP Button Stats......................................................................................... 2-1
2-4 HP Info Mode................................................................................................. 2-2
Section 3. LEVEL 1 PROGRAMMING ...................................................................................... 3-1
3-1 Modifying Product Settings ........................................................................... 3-1
3-2 AIF Clock....................................................................................................... 3-3
3-3 Deep Clean Mode........................................................................................... 3-4
3-4 Fryer Setup ..................................................................................................... 3-5
Section 4. LEVEL 2 PROGRAMMING ...................................................................................... 4-1
4-1 Advanced Product Settings ............................................................................ 4-1
4-2 E-Log (error code log).................................................................................... 4-2
4-3 Passwords ....................................................................................................... 4-3
4-4 Alert Tone (and volume) ................................................................................ 4-3
4-5 Filter After ...................................................................................................... 4-4
4-6 Filter Time ...................................................................................................... 4-4
Section 5. LEVEL 3 PROGRAMMING ...................................................................................... 5-1
5-1 Additional Advanced Product Settings .......................................................... 5-1
5-2 Special Programming ..................................................................................... 5-2
5-3 Clock Set ........................................................................................................ 5-6
5-4 Data Comm & Heat Control........................................................................... 5-6
5-5 Tech Mode...................................................................................................... 5-7
5-6 Stats Mode...................................................................................................... 5-12
Section 6. INFORMATION MODE............................................................................................. 6-1
6-1 Info Mode....................................................................................................... 6-1
Section 7. MAINTENANCE SECTION...................................................................................... 7-1
7-1 Preventive Maintenance.................................................................................. 7-1
7-2 Oil Channel Clean-Out................................................................................... 7-1
7-3 Control Panel and Menu Card Replacement .................................................. 7-2
7-4 High Temperature Limit Control.................................................................... 7-3
7-5 Main Power switch......................................................................................... 7-5
7-6 Probe Replacement......................................................................................... 7-6
FM06-040
Revised 6-11-2015 AF
July 2010

Model LVG-102, 103, 104
ii
Section 7. MAINTENANCE SECTION (Continued)
7-7 Solenoid Valves .............................................................................................. 7-9
7-8 Drain Valve Actuators .................................................................................... 7-11
7-9 Filter Pump & Motor...................................................................................... 7-12
7-10 AIF Pump ....................................................................................................... 7-14
7-11 AIF PC Board................................................................................................. 7-14
7-12 Transformers .................................................................................................. 7-15
7-13 Filter Motor Relay.......................................................................................... 7-17
7-14 Gas Control Valves......................................................................................... 7-17
7-15 Blower Motors................................................................................................ 7-19
7-16 Drain Pan Switch............................................................................................ 7-20
7-17 Filter & JIB Lights ......................................................................................... 7-21
7-18 Air Pressure Switches..................................................................................... 7-22
7-19 Ignitor & Flame Sensor Assembly ................................................................. 7-23
7-20 Ignition Modules ............................................................................................ 7-24
7-21 Pressure Transducer........................................................................................ 7-25
Section 8. PARTS SECTION
8-1 Introduction .................................................................................................... 8-1
8-2 Genuine Parts ................................................................................................. 8-1
8-3 When Ordering Parts...................................................................................... 8-1
8-4 Prices .............................................................................................................. 8-1
8-5 Delivery.......................................................................................................... 8-1
8-6 Warranty ......................................................................................................... 8-1
8-7 Recommended Spare Parts for Distributors ................................................... 8-1
Apenndix A A-1 Wiring Diagrams & Scematics....................................................................... A-1
TABLE OF CONTENTS
Section Page
July 2010

Model LVG-102, 103, 104
1-1
1-1. INTRODUCTION This section provides troubleshooting information in the form
of an easy to read table.
 Ifaproblemoccursduringtherstoperationofanewfryer,
recheck the installation per the Installation Section of the
operator’s manual.
Before troubleshooting, always recheck the operation pro-
cedures per Section 3 of the operator’s manual.
SECTION 1. TROUBLESHOOTING
Where information is of particular importance or safety related,
the words DANGER, WARNING, CAUTION, and NOTICE
are used. Their usage is described below.
SAFETY ALERT SYMBOL is used with DANGER,
WARNING, or CAUTION which indicates a personal
injury type hazard.
NOTICE is used to highlight especially important
information.
CAUTION used without the safety alert symbol indicates
a potentially hazardous situation which, if not avoided,
may result in property damage.
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
DANGER INDICATES AN IMMINENTLY
HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, WILL RESULT IN DEATH OR
SERIOUS INJURY.
1-2. SAFETY
Feb. 2010

Model LVG-102, 103, 104
1-2
1-3. TROUBLESHOOTING To isolate a malfunction, proceed as follows:
 1. Clearlydenetheproblem(orsymptom)andwhenit 
occurs.
2. Locate the problem in the Troubleshooting table.
3. Review all possible causes. Then, one-at-a-time work
through the list of corrections until the problem is solved.
4. Refer to the maintenance procedures in the Maintenance
Section to safely and properly make the checkout and
repair needed.
If maintenance procedures are not followed correctly,
injuries and/or property damage could result.
Feb. 2010

Model LVG-102, 103, 104
1-3
Problem Cause Correction
POWER SECTION
With power switch in •Open circuit •Check to see that unit is plugged in
ON position, the fryer
is completely inoperative • Check the breaker or fuse
(NO POWER) at supply box
• Check voltage at wall receptacle
• Check MAIN POWER
switch; replace if defective
• Check cord and plug
•Reset transformer circuit breaker
• Blown fuse or tripped •Reset breaker or replace fuse
circuit breaker at supply
box or control panel
•Faulty power switch. •Check power switch
•Faulty cord and plug •Check cord and plug
• Check power at receptacle
•Faulty drain switch •Check drain switch
•Faulty PC Board •Check control panel per maintenance
section and replace as needed
•High limit control switch tripped •Let unit cool down (15-20 minutes),
press red reset button under right
side of the controls; if high limit
does not reset, high limit must be
replaced
HEATING OF SHORTENING SECTION
Oil will not heat
July 2010

Model LVG-102, 103, 104
1-4
Problem Cause Correction
HEATING OF SHORTENING SECTION (Continued)
• Drain valve open •Close drain valve
(Continued)
•Faulty temperature probe •Replace temperature probe
•Faulty gas valve •Check gas valve
Oil heating too slow • Low gas pressure • Have gas pressure checked
• Wire(s) loose • Tighten
• Burnt or charred wire • Replace wire and clean
connection connectors
Oil overheating • Programming wrong • Check temperature setting
in the program mode
• Faulty PC board • Replace control board if heat
indicator stays on past ready
temperature
• Faulty temperature probe • Check probe calibration and
replace if temperature is off + 5
degress
• Faulty gas valve • Check gas valve
Oil will not heat
July 2008

Model LVG-102, 103, 104
1-5
Problem Cause Correction
OIL LEVEL SECTION
Oil foaming or boiling over vat • Water in oil • At end of a Cook Cycle, drain
and clean vat; add fresh oil
• Improper or bad oil • Use recommended oil
 •Improperltering •Refertotheprocedure
    onlteringtheoil
• Cold zone (bottom of vat) • Filter oil
full of crumbs
• Improper rinsing after • Rinse the vat thoroughly to remove
cleaning the fryer any cleaning agent in the vat
Oil will not drain from vat • Drain valve clogged with • Open valve, using cleaning brush,
force crumbs through drain valve
• Faulty actuator • Replace actuator
• Oil channel clogged • Access the clean-out plug on the
sides of the unit (see Oil Channel
Clean-out Section)
Oil leaking • Obstruction in drain • Remove obstruction
through drain valve
• Faulty drain valve • Replace drain valve
Vatisunder-lled •LocationswithRTI,the •TheRTIsystemcanbediscon-
3-way valve is stuck open nected until RTI repairs the valve
• JIB is low or empty • Fill the JIB
• JIB oil line is clogged or • Check JIB line
collapsed
Bubblesinoilduring • Filterpanneedscleaned •Cleanlterpanandchangepad
entirelteringprocess
 • Filterpannotcompletely •Makesurelterpanreturnlineis
engaged pushed completely into the receiver
on the fryer
• Filter pan clogged • Clean pan and change pad
 • Damagedo-ringonlter •ChangeO-ring   
line tube on fryer
Feb. 2011

Model LVG-102, 103, 104
1-6
Problem Cause Correction
FILTER MOTOR SECTION
Filter motor runs but
pumps oil slowly
Filter motor will not run
 “ISPOTFILLED”ltererror
prompt
“CHECK PAN” prompt
“CHANGE FILTER PAD”
prompt appears
• Filter line connections
loose
• Drain pan o-rings damaged or
missing
• Filter paper or pad clogged
• Power cord for vat #1
is not plugged-in
• Thermal reset button on
the rear of the pump motor
is tripped
• All oil did not completely
 returnafteraltercycle
• Filter pad clogged
• Filter drain pan missing
• Filter drain pan not completely
engaged
• Filter drain interlock switch not
engaged
• Filter pad has not been
changed within a 24hr time
period; Main power switch
 wasturnedoffduringlter 
pad change
• Drain pan microswitch stuck
•Tightenalllterlineconnections
• Install new o-rings
• Changelterpaperorpad
• Plug power cord into receptacle
• Remove the right side panel and
allow time for the motor to cool
and then, using a screwdriver,
press hard against the button
until it clicks
• Have manager follow prompts
• IsJIBfull?Ifnot,llJIB
• Replacelterpad/cleanpan.
• Find pan and install
•Adjustlterdrainpanposition
• Check drain microswitch
•ReplaceoldlterpadwithNEW
 lterpadwithmainpowerswitch
turned on.
 *NOTE*24/7storereplace 
 ltertwiceaday.
• Check drain microswitch
DISPLAYED PROMPT SECTION
Feb. 2011

Model LVG-102, 103, 104
1-7
1-4. ERROR CODES In the event of a control system failure, the digital display
shows an error message. The message codes are shown in the
DISPLAY column below. A constant tone is heard when an er-
ror code is displayed, and to silence this tone, press any button.
Feb. 2011
DISPLAY CAUSE CORRECTION
“E-4” Control board overheating Turn switch to OFF position, then turn switch back
to ON; if display shows “E-4”, the control board is
getting too hot; check the louvers on each side of
the unit for obstructions
“E-5”
Oil overheating Turn switch to OFF position, then turn switch back
to ON; if display shows “E-5”, the heating circuits
and temperature probe should be checked
“E-6A”
Temperature probe open Turn switch to OFF position, then turn switch back
to ON; if display shows “E-6A”, the temperature
probe should be checked
“E-6B”
Temperature probe shorted checked Turn switch to OFF position, then turn switch back
to ON; if display shows “E-6B”, temperature probe
should be
“E-10” E-10A- tripped above 300F
E-10B- tripped below 300F
E-10C- tripped while cooking
E-10D- tripped <5min. of Auto Filter
E-10F-trippedduringltercycle
E-10M- tripped during melt mode
E-10Y- tripped <5min of “YES” to
“IS THE POT FULL?” prompt
Allow fryer to cool for 15-20 minutes; reset high
limit by pressing down & releasing raisedside of
the switch for the vat that is not operating; a single
reset switch is found behind the door of each well;
if high limit does not reset, high limit must be
replaced
“E-15” Drain valve open Cleanand/orcloseshvatdrainvalve;ifcleanand
closed, have drain switch continuity checked
“E-18-A”
“E-18-B”
“E-18-C”
Left level sensor open
Right level sensor open
Both level sensors open
Turn switch to OFF position, then turn switch back
to ON; If display still indicates a failed sensor,
check the connectors at the control board; check
sensor & replace, if necessory
“E-20-A”
“FAN
SENSOR
STUCK
CLOSED”
Pressureswitchfailure/Wiring
problem
If fan is not running, have pressure switch
checked; should be open circuit, if no air pressure
If fan is running, wiring error

Model LVG-102, 103, 104
1-8
1-4. ERROR CODES (Continued)
Feb. 2011
DISPLAY CAUSE CORRECTION
“E-20-B”
“NO
DRAFT”
“CHECK
FAN”
PressureSwitchfailure/hoseloose
DraftFanfailure/lowvoltage/Flue
or hood obstruction
Press power button to vat off and back on again,
if E-20-B persists, have pressure switch checked;
should be open circuit if no air pressure; make sure
hose is connected to fan and pressure switch
Have draft fan checked; low voltage going to fan
Checkthefryerueandhoodsystemfor
obstructions
“E-20-D”
• Failuretoignite/noamesense
• Plugged atmospheric
equalization hole in regulator cap
resultinginpilotameslowly
fading
• Press power button to vat off and back on
again, if E-20-D persists, check gas line
connections; check gas shutoff valve; check
ignitionmodule;checkgasvalve;checkame
sensor gap; check gas valve, and check ignition
module wiring
• Clear obstruction from hole
“E-21”
Slow heat recovery Haveacertiedservicetechniciancheckthefryer
for correct gas supply and pressure to the unit;
have the gas valves checked; have unit checked
for loose or burnt wires
“E-22”
“NO
HEAT”
Burner not igniting Have gas valve and heat circuit checked
“E-41” ,
“E-46”
Programming failure Turn switch to OFF, then back to ON; if display
shows any of these error codes, re-initialize the
controls; if error code persists, check control board
and replace as needed
“E-47” Analog converter chip or 12 volt
supply failure
Turn switch to OFF, then back to ON; if “E-47”
persists, replace the PC board
“E-48” Input system error Turn switch to OFF, then back to ON; have control
PC board replaced if “E-48” persists
“E-54-C”
Temperature input error Turn switch to OFF, then back to ON; have control
PC board replaced if “E-54C” persists

Model LVG-102, 103, 104
1-9
1-4. ERROR CODES (Continued)
May 2016
DISPLAY CAUSE CORRECTION
“E-60”
AIF PC board not communicating
with control PC board
Turn switch to OFF, then back to ON; if “E-60”
persists, check 1.5 amp fuse on AIF PC board on
International units only; check connector between
the PC boards; replace AIF PC board or control PC
board if necessary
“E-62A”
Communication error -Verify the OQM senser wiring is correct.
-Replace cable.
-Replace Sensor
“E-62B” Wrong calibration parameter Replace OQM Sensor
“E-62C” Shorted capacitance Replace OQM Sensor
“E-62D” Shorted RTD Replace OQM Sensor
“E-62E” Open RTD Replace OQM Sensor
”E-62F” Open capacitance Replace OQM Sensor
”E-62G” Out of range (TPM value over 35) Replace oil and take a TPM reading, if the error is
still present replace OQM sensor.
“E-70-C”
Drain valve jumper wire missing or
disconnected
Have the jumper wire checked on the PC board at
drain switch interlock position
“E-82A”
Selector Valve not detected Have wiring checked between Selector Valve and
AIF board
“E-82B” Selector Valve failed Have the “Home” switch on Selector Valve
checked
“E-83”
“PRES-
SURE ”
“TOO
HIGH”
Pressure Trasducer senses too high
pressure in AIF system
Check AIF system or the RTI quick-disconnect;
See details below;
“E-83-A” Pressure too high Check AIF system in Vat #1
“E-83-B” Pressure too high Check AIF system in Vat #2
“E-83-C” Pressure too high Check AIF system in Vat #3
“E-83-D” Pressure too high Check AIF system in Vat #4
“E-83-E” Pressure too high Check AIF system in Vat #5
“E-83-J” RTI “JIB FILL” switch ON when
pressure too high
CheckJIBllvalves
“E-83-R” RTI “DISPOSE” switch ON when
pressure too high
Check RTI quick-disconnect behind fryer; RTI
phone no. if needed: 888-796-4997
“E-83-Z” Unknown source CheckRTIsystem&JIBllvalve
“E-93-A” 24VDC tripped Have drain actuator checked

Model LVG-102, 103, 104
2-1
SECTION 2. INFO, FILTER & TEMP BUTTON STATS
2-1. INFO BUTTON STATS Recovery Information for each Vat/OQM Information
1. Press and release and REC shows in left display and
the recovery time that oil temperature went from 250°F
(121°C) to 300°F (149°C) shows in the right display. For
example, means it took 5 minutes and
30 seconds for the oil temperature to recover to 300°F
(149°C) from 250°F (121°C).
Pressing the button twice shows the 2nd language, if
programmed.
If no buttons are pressed within 5 seconds in any of stats
modes, the controls revert back to normal operation.
1a. Press and release , the display will show the last TPM
reading, date of the last TPM reading, and time stamp of last
TPM reading (only if OQM sensor is installed and enabled).
Cook Cycles Remaining before Filtering
1. Press and release either or and left display
shows “COOKS REMAIN” and right display shows the
 numberofcookcyclesbeforethenextautolter.For
example,
means after 3 more cook cycles on the left vat, the controls
 askoperatoriftheyarereadytolterornot.But,6more
cook cycles remain on the right vat.
Time and Date
2. Press either or twice and time-of-day and date
shows in the displays.
Filter Pad Usage
3. Press either or three times and number of hours
 thepresentlterhasbeenusedishowninthedisplays.
Actual Oil Temperature
1. Press and the actual oil temperature shows in the
display, for each vat.
Set-point Temperature
2. Press twice and SP shows in the display, along with
the set-point (preset) temperature of each vat.
REC 5:30
2-2. FILTER BUTTON STATS
2-3. TEMP BUTTON STATS
REMA IN 3 6
May 2016

Model LVG-102, 103, 104
2-2
2-4. HP INFO MODE Cook Cycles Remaining before Filtering
Press and release both and at the same time to
enter HP Info Mode. You can view the following option in HP
Info Mode:
1. E-Log
2. Last Load
3. Daily Stats
4. Review Usage
5. Inputs HDE (to check: high limit, drain switch jumper, and
tilt switch)
6. OutputsS_H(safteycontactor/heatcontactor)
7. Oil Temperature
8. CPU Temp
9. Communication OQM Sensor
10. Analog
11. Activity Log
12. Oil Levels (see if low level sensing temperature difference
between probes).
13. Pumps and Valves
14. AIF Info (check for drain pan recognition: Left F button 1X
and down arrow 2X.
15. Print Report to USB
16. Remove USB
17. Oil Quality Support
a. Software Version (SVN); hardware (HVN)
b. Serial Number
c. RTC Date
d. RTC Time
e. Vat-1
f. Vat-2
g. Vat-3
h. Vat-4
i. Vat-5
j. Vat-6
k. Vat-7
l. Vat-8
18. oil quality (OQ) history
May 2016

Model LVG-102, 103, 104
3-1
Level 1 contains the following:
• Modify product settings
• Set the AIF clock for products
• Perform the Deep Clean procedure
• Fryer Setup Mode
1. Press and hold and buttons until LEVEL - 1
shows in the display, followed by ENTER CODE.
2. Entercode1,2,3,4(rst4productbuttons).
“PRODUCT” and “SELECTN” show in the displays.
3. Press right √button and ‘SELECT PRODUCT’ and “-P 1-”
(ex: NUGGETS) show in the displays.
Change Product Names
4. Use the and buttons to scroll through 40 products,
or press desired product button
5. Press right √button and the product (ex: NUGGETS)
shows in left display and “MODIFY”, and “YES NO”
shows in right display. Press √button to change this
product, or press the Xbutton to choose another product.
6. If √button was pressed, press and release a product button
 andtheashingletterchangestotherstletterunderthe
product button that was pressed. For example, if
 pressed,theashingletterchangestoan“A”.
 Presssamebuttonagainandtheashingletterchangestoa
 “B”.Pressitagainandtheashingletterchangestoa“C”.
Once desired letter shows in the display, press button
to continue to the next letter and repeat the procedure.
Press and hold the right Xbutton to exit Program Mode, or
press button to continue on to “1. COOK TIME”.
To Change Times and Temperatures
7. Press button until “COOK TIME” shows in display,
and then use product buttons
to change the time in minutes and seconds, to a maximum
of 59:59.
SECTION 3. LEVEL 1 PROGRAMMING
3-1. MODIFYING PRODUCT
SETTINGS
Dec. 2007

Model LVG-102, 103, 104
3-2
8. Press and release button and “TEMP” shows in the
display, along with the preset temperature on the right side
of the display.
Press the product buttons
to change the temperature. The temperature range is 190°F
(88°C) to 380°F (193°C).
Cook ID Change
9. Press button until “COOK ID” shows in the display
along with the product ID. For example, NUG would be
the ID for nuggets. Use the product buttons to change the
ID, following the same procedure as Steps 4 thru 6 above.
Alarms (Duty 1 & 2)
10. Press button until “DUTY 1” shows in left display,
and an alarm time in the right display. Press the product
buttons to set an alarm.
Ex., If a Cook Cycle was set at 3 minutes, and an alarm
was to go off after 30 seconds into the Cook Cycle, “0:30”
would be set in the display at this time. When the timer
counts down to 2:30 the alarm sounds.
After alarm time is set, press button and “DUTY 2”
shows in display, and a second alarm can be programmed.
Quality Timer
11. Press button until QUAL TMR shows in display along
with preset holding time. Press product buttons to adjust
hold time (2 hrs., 59 min. max.).
AIF Disable
12. Press button until “AIF DISABLE” shows in display
along with “YES” or “NO”. Using and buttons
change the display to “YES” if that product is to not be
includedintheautomaticintermittentltrationoperation,
or “NO” if it is to be included.
Assign Button
13. Press button until “ASSIGN BTN” shows in the
display, along with the product (ex: NUGGETS). If this
product already has a product button assigned to it, that
LED will be lit. To assign other product buttons to that
product, press and hold the product button for 3 seconds
and that LED stays lit. To remove a product from a button,
press and hold the product button with a lit LED and the
LED goes out.
3-1. MODIFYING PRODUCT
SETTINGS (Continued)
Feb. 2011

Model LVG-102, 103, 104
3-3
This feature allows controls to be set for periods of the day that
block the automatic “Filter Now” prompts. For example, the
controls could be set not interrupt with “Filter Now” prompts
duringthelunchrush,andduringthesupperrush.But,iflter-
ing is desired during this time, press and hold a button to
accesstheltermenu.
EachAIFBlockingperiodisdenedbyastarttime(atimeof
day, XX:XX A, etc) and a duration in minutes.
Weekdays M-F are all grouped together. Up to four different
AIF blocking periods may be programmed throughout the day
for Monday - Friday. (All days share the same settings.)
A separate set of four blocking periods may be programmed
forSaturdays,andanalsetoffourblockingperiodsmaybe
programmed for Sundays.
1. Press and hold and buttons until LEVEL - 1
shows in the display, followed by ENTER CODE.
2. Entercode1,2,3,4(rst4productbuttons).“PRODUCT”
and “SELECTN” show in the displays.
3. Press button once and “AIF CLOCK” show in
displays.
4. Press √button and use and buttons to scroll
through “ENABLE” and “DISABLE” and then press √
button again to select one.
5. If “ENABLE” is chosen, then and buttons can be
used to scroll through following list of blocking periods:
Left Display Right Display
M-F 1 XX:XX A XX
M-F 2 XX:XX A XX
M-F 3 XX:XX A XX
M-F 4 XX:XX A XX
SAT 1 XX:XX A XX
SAT 2 XX:XX A XX
SAT 3 XX:XX A XX
SAT 4 XX:XX A XX
SUN 1 XX:XX A XX
SUN 2 XX:XX A XX
SUN 3 XX:XX A XX
SUN 4 XX:XX A XX
3-2. AIF CLOCK
Dec. 2011

Model LVG-102, 103, 104
3-4
3-3. DEEP CLEAN MODE
3-2. AIF CLOCK
(Continued)
In 12-hour clock mode, there are three items on each line: the start
time“XX:XX”,theAorP(am/pm)setting,andthe“XX”duration.
Usetheandbuttonstosettheseitems,whichasheswhen
the item is selected.
To set a new start time setting, use the product buttons,
to enter the new value.
PressthebuttontostepovertotheAM/PMsetting.TheAorP
can be toggled by pressing the ‘0’ product button.
Press the button again to step over to the duration value (in
minutes). Enter a new value using the product buttons,
In 24-hour clock mode, there are only two items on each line: the
time (XX:XX) and the duration (XX). Again, the and
buttons step you between these items.
Press the right-side Xbutton to exit out of AIF Clock programming
mode.
This procedure allows a thorough cleaning of the vat by remov-
ing caramelized oil from vat. See Section 4-3 in the Operator’s
Manual for complete set of instructions.
Jan. 2008

Model LVG-102, 103, 104
3-5
This mode has the same settings as seen upon initial start-up of the
fryer.
1. Press and hold and buttons until LEVEL - 1
shows in the display, followed by ENTER CODE.
2. Entercode1,2,3,4(rst4productbuttons).“PRODUCT”
and “SELECTN” show in the displays.
3. Press button 3 times and “FRYER SETUP” show in
the displays.
4. Press √button and *SETUP* *MODE* shows in displays,
followed by, “LANGUAGE” on the left display,
“ENGLISH” on the right display.
Use or buttons to change the operation display to,
“FRANCAIS”, “CAN FREN”, “ESPANOL”, “PORTUG”,
“DEUTSCHE”,“SVENSKA”,“РУССКИИ”.
Press to continue with other set-up items which include:
• TEMP FORMAT - oF or oC
• TIME FORMAT - 12-HR OR 24-HR
• ENTER TIME - Time of day (use product buttons to change)
• ENTER TIME - AM OR PM
• DATE FORMAT - US OR INTERNATIONAL
• ENTER DATE - Today’s date (use product buttons to change)
• FRYER TYPE - GAS or ELEC
• VAT TYPE - FULL OR SPLIT
• DISPOSEBULKOIL-YES/NO(BULKhasRTIsystem)
• SUPPLYBULKOIL-YES/NO(BULKhasRTIsystem)
• DAYLIGHT SAVING TIME - 1.OFF; 2.US (2007 & after);
3.EURO; 4.FSA (US before 2007)
• OIL QUALITY ENABLED (yes or no)
• TPM WARN (value can be set to 0% - 40%)
• TPM MAX (value can be set to 0% - 40%)
Unless otherwise indicated, use or to change settings.
3-4. FRYER SETUP
May. 2016