Herman Miller Canvas Office Landscape User manual

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2ghc rev E.
1
YCanvas Office Landscape® Interiors Base Power Harness Assembly
Installation and Disassembly for Recycling Instructions
Parts Included:
120/208V, 120/240V 20A (15A CSA)
15A when powered with energy manager (PT 130, PT 131)
1. A 20A rated circuit can supply a maximum of 13 receptacles
at 15 A.
2. A 15A rated circuit can supply a maximum of 10 receptacles
rated at 15A. Receptacles rated at 20A are not allowed.
Electrical Rating:
WARNING
Disconnect power before installation. Failure to do so can
cause electrical shock and personal injury.
WARNING
Electrically interconnected units must be mechanically
interconnected.
!
!
Base Power Harness Assembly 30”-48”
Base Power Harness Assembly 24”
A
A
Festoon Connector
B
Safety Glass
Tools Required:

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2ghc rev E.
2
1
1. Set frame on side.
2. Insert Hooks on Harness Assembly (A) into Slots in bottom of Frame. Slide Harness
Assembly along frame until Hooks engage in slots and Anti-Dislodgement clip
engages into Square Hole.
Note: Installing Raceway Cover Supports before Harness Assembly will make
installing Raceway Covers easier.
Hook
Square Hole
Slot
Raceway Cover Support
Raceway Cover Support
Anti-Dislodgement
Clip
A
Assembly Instructions:

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2ghc rev E.
3
2
1. Connect Power Harness Assemblies together, Frame to Frame, with Festoon
Connector (B).
2. See diagrams at right for proper panel connections.
B
2-Way Intersection Connection
B
Frame Stile
Power Harness

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2ghc rev E.
4
3-Way Intersection Connection 4-Way Intersection Connection
BB
BBB
Frame Stile
Frame Stile
Power Harness Power Harness
Disassembly for Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling codes.
Use these codes to identify material type for recycling. Non marked components
should be treated as mixed plastic. Ferrous metals can be identied using a
small magnet for recycling. Non-ferrous metals should be separated and recycled
separately.
To disassemble product, reverse steps 2 through 1.