Herman Miller Canvas Vista Installation instructions

Power Driver #2 Phillips
Bit
Metric Allen
Wrench
Tools Required
Parts Included
HermanMiller
Canvas Vista Fixed Height Table
Installation and Disassembly for
Recycling Instructions
How to assemble Fixed Height Table
FG2B1
FG696
FGX10 Spacer
Tapping Screw
FG2B2
Instructions for A-Leg Desks
Note: Assemble legs to worksurface with the worksurface upside down.
. Assemble upper stamping/plate to bottom of worksurface by
aligning the holes on the upper stamping with the predrilled holes in
the bottom of the worksurface. There are two pre-drilled holes which
align to the outer most holes along the length of the upper plate.
Orient the upper stamping so that the small rectangular extended tab
in facing inboard (towards center of worksurface).
. Use  screws from hardware kit to fasten the plate to the
worksurface. Repeat this step for the other leg.
Note: Outbound Leg location shown. Inbound leg location will be
approximately  /” in from the edge of the table. For the condition
where one leg is inbound, one leg is outbound, pre-drilled holes will
locate the inbound leg. The outbound leg will be centered on the
surface front to back and /” in from the edge of the surface to the
edge of the top plate.
/”
Step  - Assemble leg to worksurface
1HermanMiller Installation Instructions1BMV2B rev A

2HermanMiller Installation Instructions1BMV2B rev A
Step 
Note: Install stiener with worksurface upside down and elevated.
. Align stiener with pre-drilled holes on the bottom of the
worksurface near the legs. Fasten the stiener to the back side of
worksurface using tapping screws.
. Install tapping screws two in each end then in every other hole.
Alternate back and forth on each flange.
(Note: for ” deep surfaces the stiener is centered on the surface.
For ” deep surfaces the stiener is Shied toward the from edge by
about /”.)
Note: Assemble legs to worksurface with the worksurface upside
down.
. Align the upper stamping with the pre-drilled holes in the
bottom of the worksurface. There are two pre-drilled holes which
align to the outer most holes along the length of the upper plate.
Orient the plate so that the small rectangular tab extension is
facing inboard (towards center of worksurface).
. Fasten the upper stamping to the bottom of the worksurface
with  screws from hardware pack. Repeat this step for the
other leg.
Note: Outbound Leg location shown. Inbound leg location will
be approximately  /” in from the edge of the table. For the
condition where one leg is inbound, one leg is outbound,
pre-drilled holes will locate the inbound leg. The outbound leg
will be centered on the surface front to back and /” in from the
edge of the surface to the edge of the top plate.
Instructions for T-Leg Desks
/”

3HermanMiller Installation Instructions1BMV2B rev A
Step  - Install stiener to worksurface.
. Fasten the spacer and cast T-foot to the leg tube with two cap
screws from hardware kit.
. Repeat these steps for the other leg.
Note: Install stiener with worksurface upside down and elevated
. Align stiener with pre-drilled holes on the bottom of the
worksurface near the legs. Fasten the stiener to the back side of
worksurface using tapping screws.
. Align the cast T-foot (” Table or ” Table) to the holes on the
spacer and leg tube.
Step 
. Place the spacer on the bottom of the Leg tube.

4HermanMiller Installation Instructions1BMV2B rev A
For more information about our products and services please visit us at
hermanmiller.com or call ()  .
© Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A. Part No. BMVB  A
. Install tapping screws in two in each end then every other
hole. Alternate back and forth on each flange.
(Note: for ” deep surfaces the stiener is centered on
the surface. For ” deep surfaces the stiener is Shied
toward the from edge by about /”.)
Disassembly and Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling
codes. Use these codes to identify material type for recycling. Non
marked components should be treated as mixed plastic. Ferrous metals
can be identied using a small magnet for recycling. Non-ferrous metals
should be separated and recycled separately.
To disassemble product, reverse the above installation steps: