Herman Miller Canvas Office Landscape Interiors 120 Installation instructions

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b3cxr rev E.
1
YCanvas Office Landscape® Interiors 120° Full Height & Change of Height
Connector Cover Installation and Disassembly for Recycling Instructions
Parts Included:
IMPORTANT: Save these instructions for layout changes.
One-sided COH
Connector Cover
(Painted & Veneer)
One-sided
Connector Cover
(Painted & Veneer)
Two-sided COH
Connector Cover
(Painted & Veneer)
Change of Height
Trim Block
Change of Height
2-Sided Trim Block
(Painted & Veneer)
Change of Height
Trim Block Clip Attachment Clip
A
G
B
C
D
EF
Tools Required:
Safety Glass

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b3cxr rev E.
2
1
1. Locate slots, anges, and tabs in One-sided
Full Height Cover Connector (G). Make sure
the tabs are at the top of the part.
2. Install One-sided Full Height Connector
Cover (G) by placing edge of Connector next
to Connector Tube and rotating so that anges
engage around edges of Connector Tube.
3. Slide One-sided Full Height Connector Cover
(G) down so that tab rests on connector Tube.
One-sided Full Height
Connector Cover G
Tabs
Slots
Tab
Connector
Tube
Flanges
G
Assembly Instructions:

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b3cxr rev E.
3
A
A
C
Connector
Tube
Top Cap
Connector
Upper
Frame
Top Cap
Lower
Frame
Top Cap Tiles
1. Locate slots, anges, and tabs on COH
Connector Cover (A).
4. Slide COH Connector Cover
Assembly down over Connector
Tubes so that tab rests on
Connector Tube.
5. Install tiles on frames.
6. Insert Top Cap Connector into
Upper Frame Top Caps.
7. Attach Upper Frame Top Caps
to frames making sure Top Cap
Connector ts into Connector
Cover (A)
8. Attach Lower Frame Top
Caps and slide over (C).
2. Install COH Trim Block (C) on the bottom
of Connector Cover (A), making sure tabs
are at the top.
3. Install COH Connector Cover Assembly
by placing edge of Connector next to
Connector tube and rotating so that anges
engage around edge of Connector Tube.
2One-sided COH Connector Cover

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b3cxr rev E.
4
3Two-sided COH Connector Cover
1. Install tiles on frames.
2. Install Attachment Clip (F) on
Frame.
3. Install COH Trim Block Clips (E)
on Trim Block (D) only on the sides
where frame top caps will mate
4. Install COH 2-sided Trim Block (D)
with Clip or Clips (E) on wire channel
and the lower connector cover.
5. Slide lower frame Top Caps over
Trim Block Clips (E). Frame Top Caps
must be snapped to Top Hook Rails
and slide over Trim Block Clip (F) and
Trim Block Clip (E).
6. Attach and slide 2-Sided Connector
Cover (B) over Attachment Clip (F) and
Trim Block (D).
7. Insert Connector Top Cap into Frame
Top Caps.
8. Attach Top Caps to Frames making
sure the Connector Top Cap ts into
Connector Cover (B).
Light Seal
ush at top
Cover must slide
over Attachment
Clip
Lower
Connector
Cover
Lower Top Cap
Connector
Top Cap
Top Hook Rail
Wire Channel
F
E
B
B
D
E
D

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b3cxr rev E.
5
Disassembly for Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling codes.
Use these codes to identify material type for recycling. Non marked components
should be treated as mixed plastic. Ferrous metals can be identied using a
small magnet for recycling. Non-ferrous metals should be separated and recycled
separately.
To disassemble product, reverse the above installation steps.