Herman Miller Aeron Installation instructions

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 1
Part no. 1b9vtf rev A.
YAeron®Disassembly for Recycling
Tools Required:
Materials Identication and Segregation:
Disassembly Steps:
Power Driver Safety Glasses Torx Bit2 lbs Hammer Rubber Mallet
Where possible, plastic components are marked with ASTM recycling codes. Use
these codes to identify material type for recycling. Non marked components should
be treated as mixed plastic. Ferrous metals can be identied using a small magnet
for recycling. Non-ferrous metals should be separated and recycled separately.
1. Lay chair on back. 2. Grasp and pull to remove
casters from the base.

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 2
Part no. 1b9vtf rev A.
5. Hold base legs rmly and
strike the bottom of cylinder
with a rubber mallet until
base comes loose.
4. Pull out the base from
assembly.
3. Hit the bottom of the chair
with hammer until cylinder
separates from chair.
6. Remove base.

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 3
Part no. 1b9vtf rev A.
7. Using ratchet wrench and
6mm hex bit to remove hip
pivot screw from each swing
arm.
9. Remove seat frame prop-
erly.
8. Using 10mm socket,
ratchet wrench and 4mm hex
key to remove nut and screw
attaching seat link to seat
frame.
10. Using 6mm socket,
ratchet wrench remove front
B-link bolts.

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 4
Part no. 1b9vtf rev A.
13. Depress base of
wishbone and disconnect
cable end from keyhole slot
in wishbone.
12. Adjust control mechanism
counter-clockwise to set
posture t at minimum
support setting.
11. Remove the seat link.
Posture Fit Removal:

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 5
Part no. 1b9vtf rev A.
15. Using screwdrivers,
remove screws from wish-
bone.
16. Dispose support pad and
wishbone properly.
14. By hand, grasp wishbone
upper arms and slide wish-
bone with support pad up off
back frame.
17. Carefully insert awl into
pellicle and remove to create
opening where cable tip will
pass through.

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 6
Part no. 1b9vtf rev A.
21. Using phillips screw
driver, remove screw posture
t cable bracket to chair back
frame.
19. Using #2 phillips head
screwdriver, remove screws
fastening mounting bracket
to control mechanism.
20. Remove control mecha-
nism from swing arm.
18. Slide cable sleeve into
cable receiver.

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 7
Part no. 1b9vtf rev A.
22. Remove lumbar from
back.
24. Remove back frame and
set aside.
23. Using ratchet wrench
and 5mm hex bit to remove
(4) screws attaching back
frame to swing arms.
25. Using #2 phillips head
screwdriver, remove screws.

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 8
Part no. 1b9vtf rev A.
26. Dispose arm pad safely.
28. Using #2 phillips head
screwdriver, remove and
discard (2) screws securing
pneumatic actuator to tilt.
27. Remove upper tilt cover.
29. Using pliers, pull pneu-
matic knob from chair. Prop-
erly dispose of pneumatic
knob.

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 9
Part no. 1b9vtf rev A.
30. Using #2 phillips head
screwdriver, remove and
discard (2) screws securing
pneumatic control end to
swing arm.
32. Using pliers, twist off
appropriate tilt knobs from
lever of tilt control.
31. Remove pneumatic
cable assembly from chair
and dispose of properly.
33. Using #2 phillips head
screwdriver, remove the
screws from tilt control cover.

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 10
Part no. 1b9vtf rev A.
34. Remove lower tilt cover.
36. Remove Spacer from the
tilt.
35. Remove swing arm.
37. Remove Activation
power cable.

Z
© 2011 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron, Co/Struc and Mirra are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, Tu and Sayl are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products. 11
Part no. 1b9vtf rev A.
38. Using hand pull the
pellicle from the seat frame
and remove.
39. Using hand pull the
pellicle from the back frame
and remove.