Hi-Target V100 User manual

I
Manual Revision
File number：YFZ-2015-0741
Revision Date Revision
Level Description
Nov.2015.04 1 V100 GNSS RTK System User Manual A/1

Preface
II
Preface
Introduction
Welcome to use Hi-target V100 receiver, this introduction is
applicable to Hi-Target V100 products. V100 is a new type of
GNSS receiver used for measurement. The introduction
describes how to install, set and use V100 products.
Experience Requirement
In order to help you better use Hi-Target series products,
Hi-Target suggests you carefully reading the instruction. If you
are unfamiliar with V100 products, please refer to
www.hi-target.com.cn
Tips for safe use
Note: the contents here generally are special
operations, needing your special attention.
Please read the contents carefully.

V100GNSSRTKSystemUserManual
III
Warning: the contents here generally are very
important. In case of failing to operate
based on warning contents, it will
damage the machine, lose the data, break
down the system and endanger personal
safety.
Exclusions
Before using the products, please carefully read the operating
instruction, and it will help you better use the product.
Hi-Target Surveying Instrument Co., Ltd will not assume the
responsibilities if you fail to operate the product according to
the requirements in operating instruction, or operate the
product wrongly because of failing to understand the operating
instruction.
Hi-Target is committed to constantly perfect product functions
and performance, improve service quality and reserve the
rights to change the contents in operating instruction without

Preface
IV
separate notice.
We have checked the consistency between contents in
instruction and software & hardware, without eliminating the
possibility of deviation. The pictures in operating instruction
are only used for reference. In case of inconformity with
products, the products shall prevail.
Technology and Service
If you have any technical issues, you can call company
technology department for help, we will answer your
question in time.
Relevant Information
You can get this introduction in the following ways:
1. After purchasing hi-target V100 receiver,there will be
“V100 GNSS RTK System User Manual” in the
instrument container to guide you how to operate
instrument.

V100GNSSRTKSystemUserManual
V
2. Log in hi-target official website, download the electronic
version introduction in “Download Center” →“Manual”
→“Surveying Products”
Advice
If you have any advice or suggestion on V100, please call us
or Dial the national hotline: [phone]. Your feedback
information will improve the production quality more.

Content
VI
Content
Product Introduction ...................................... 1
Preface ............................................... 2
Product Characteristics ............................... 3
Cautions for Use ...................................... 3
Introductions to Receiver ................................. 5
Receiver Appearance ................................... 6
Control Panel ......................................... 6
Upper Cover ........................................... 7
Bottom Cover .......................................... 7
Power Supply System ................................... 9
Environmental Requirements ........................... 13
Electronic Jamming ................................... 14
Elementary Operation ..................................... 15
Control Panel ........................................ 16
Function Key ......................................... 16
LED Function ......................................... 17
Working Mode Switch .................................. 18
Rovel Handheld Difference ............................ 19
Static Collection .................................... 22
Static Data Storage .................................. 24
Static Data Download ................................. 25
Firmware Upgrading ................................... 26
Technical Parameters ..................................... 28
GNSS Configuration ................................... 29
System Configuration ................................. 30
Built-in Communication ............................... 30
Control Panel ........................................ 30
External Interface ................................... 30
Electric Characteristics ............................. 30
Physical Characteristics ............................. 31
Environment Characteristics .......................... 31
Private Cloud Service ................................ 31
Socket and Main Accessories .............................. 32

V100GNSSRTKSystemUserManual
VII
Preface .............................................. 33
Five-pin Socket ...................................... 33
Five-wire ............................................ 34
Mini USB Cable ....................................... 36
Measurement Bench Marker ............................. 37
Schedule 1 control panel lights .......................... 38
Schedule2 factory default parameters ..................... 39

Product Introduction
1
Product Introduction
This chapter describes:
■Preface
■Product Characteristics
■Cautions for Use
C H A P T E R
1

ProductIntroduction
2
Preface
V100 is a new subminiaturized type of GNSS receiver
used for measurement pushed forward by Hi-Target Brand,
used a delicate design, Magnesium alloy construction,
multi-satellite and multi-frequency technique, built-in
constellation motherboard, Bluetooth both with dual-mode and
long-distance , it is a realization of quick, efficient , safe
measurement GNSS receiver.
Warning: the instruction represents no standard
configuration. The articles within the
box can be adjusted according to
different user requirements. The
specific configuration shall be subject
to the outgoing list upon purchasing.
The suggestions before using the
machine: check whether the product
package is damaged; please open the
package carefully and confirm whether
the articles are consistent with
outgoing list; in case of loss or damage
in the product and its accessories,
please immediately contact with local
office or dealers; please carefully read
the operating instruction before
carrying, transporting and using the

V100GNSSRTKSystemUserManual
3
product.
Product Characteristics
A new generation of subminiaturized GNSS RTK，
equipped with new efficient intelligent real-time core
platform;
Using BDS constellation system, Support BDS, GPS,
GLONASS;
Subminiaturized zero-phase antenna ;
Built-in 4.0 standard long-distance dual-mode Bluetooth,
backward compatible 2.1standard Bluetooth;
Built-in 8GB large capacity data memory;
Equipped with iHand20 intelligent hand held or industrial
tablet PC;
Handbook controller receives differential signal;
Designed for the Android development of customized
smart metering software--Hi-Survey；
A key Multifunction；
New subminiaturized fuselage，Magnesium alloy structure，
more solid；
Cautions for Use
V100 receiver used Chemical resistance and impact
resistance design ，but we also need carefully use and

ProductIntroduction
4
maintenance the sophisticated instruments.
Warning: the receiver shall be in stipulated
temperature range upon using and
storage. The detailed requirements are
shown in ChapterⅣ:
Technical Parameters—> Environment
Characteristics.
In order to guarantee the quality of continuous tracking
observation and satellite signals, it is required that the
overhead observation station shall be open, without flaky
barriers above 15° elevating angle; in order to diminish the
interference of electromagnetic wave to GNSS satellite signals,
the observation station shall be free form strong
electromagnetic wave within the range of 200m, such as
television tower, microware station and high-voltage
transmission line; in order to avoid or reduce multiparty effect,
the observation station shall be far away from the terrain and
ground features with strong reflection against electromagnetic
wave signal, such as high-rise buildings, waters, etc.

V100GNSSRTKSystemUserManual
5
Introductions to Receiver
This chapter describes:
■Receiver Appearance
■Control Panel
■Upper Cover
■Bottom Cover
■Power Supply System
■Environmental Requirements
■Electronic Jamming
C H A P T E R
2

IntroductionstoReceiver
6
Receiver Appearance
The product appearance is divided into three sections，upper
cover, bottom cover and control panel.
Figure 2-1
Control Panel
The control panel includes a power switch button, three
indicators, namely satellite lights, power light (bi-color light),
signal light (bi-color light).
Satellite light power light
signal light
Power Button Functions: Startup, shutdown, operating mode
switching, automatically set the base station, reset the board
upper cover
bottom cover
control panel

V100GNSSRTKSystemUserManual
7
and so on.
Upper Cover
Figure 2-2
Loss Prevention boss: boss can effective anti-wear;
Color Mode: appearance of the structure, Clear , beautiful,
drop
Bottom Cover
Including battery compartment, five-pin socket,Mini USB
interface.
Loss Prevention boss
Color Mode

IntroductionstoReceiver
8
1- Screw connection 2- Battery compartment 3- Five-pin socket 4-Mini USB
interface 5- protective plug
Figure 2-3
Connection screw: for the instrument fixed to the base or
the pole.
Battery compartment: for housing lithium batteries.
Five-pin socket: For connection to the host and external
data links and external power source.
Mini USB interface: For connection to the host and
external devices, upgrade firmware and download
The static data can also charge or supply electricity to the
host.
3
4
5
2
1

V100GNSSRTKSystemUserManual
9
Protective plug: socket for dust and waterproof.
Note: If it is unnecessary to use five-pin socket,
and USB interface, please cover the rubber
plug to prevent dust.
Power Supply System
Battery and adapter
Table 2.1 Battery, adapter type
name type
lithium battery BLP-6300S
Power adapter PSAI10R-050Q
Lithium battery appearance:
Figure 2-4
ada
p
te
r

IntroductionstoReceiver
10
Figure 2-5
Recharge
V100 lithium battery shall use PSAI10R-050Q power
adapter to charge, about 7 hours of charging time.
Warning: 1. only the battery and charger configured
by the manufacturer can be used; the
battery shall not be thrown into fire or
used in metal short circuit electrode.
2. It shall stop using in case of heating,
deformation, liquid leakage, smelling or
other abnormal reactions during using,
charging or storage process. It shall
exchange new battery.
3.Itshallstopusingincaseoftheservice
time of battery is shortened , the battery
is aged, it shall exchange new battery.
4. Charge environment can't be higher than
40℃.
Battery installation and removal
Installation
1) Push up the battery cover button, then uncover it.

V100GNSSRTKSystemUserManual
11
Figure 2-6
2) Align battery pole with battery compartment pole, boost
until it flush with battery cover and the mental button
upspring.
Figure 2-7
Battery cover button
battery pole
Metal button

IntroductionstoReceiver
12
Figure 2-8
3) Close the battery cover to finish installing.
Removal
Push up the battery cover button to uncover it, then press the
metal button and remove battery.
Power supply
Table 2.2 power supply mode
power
supply
power supply
mode
internal：lithium battery
external：USB, Five-pin socket
scope of
external power
supply
USB socket：DC power 4.2-5.5V/1.5A
Five-pin socket：DC power 6-28V/1A
Upon external power supply, the host will automatically
detect the voltage of lithium battery and external power
supply, and supply power choosing higher voltage. As for
external power supply, it shall use the special power
specified by Hi-Target.