Hi-Target V100 User manual

V100 GNSS RTK
System Getting Started
Hi-Target Surveying Instrument Co., Ltd.
All Rights Reserved

II
Manual Revision
File number：
Revision Date
Revision
Level
Description
2015-11-30
1
V100 GNSS RTK System User Manual

V100 GNSS RTK System Getting Started
III
Preface
Introduction
Welcome to use Hi-target V100 receiver, this introduction is
applicable to Hi-Target V100 products. The introduction describes
how to install, set and use V100 products.
Experience Requirement
In order to help you use Hi-Target series products better, Hi-Target
suggests you carefully reading the instruction. If you are unfamiliar
with V100 products, please refer to www.hi-target.com.cn
Tips for safe use
Notice: The contents here generally are special operations, needing
your special attention. Please read the contents carefully.
Warning: The contents here generally are very important. Such
wrong operation may make the machine damaged, make
the data lost, even breaks down the system and
endangers personal safety.

Preface
IV
Exclusions
Before using the products, please carefully read the operating
instruction, and it will help you better use the product. Hi-Target
Surveying Instrument Co., Ltd will not assume the responsibilities
if you fail to operate the product according to the requirements in
operating instruction, or operate the product wrongly because of
failing to understand the operating instruction.
Hi-Target is committed to constantly perfect product functions and
performance, improve service quality and reserve the rights to
change the contents in operating instruction without separate
notice.
We have checked the consistency between contents in instruction
and software & hardware, without eliminating the possibility of
deviation. The pictures in operating instruction are only used for
reference. In case of inconformity with products, the products shall
prevail.

V100 GNSS RTK System Getting Started
V
Technology and Service
If you have any technical issues, you can call Hi-Target technology
department for help, we will answer your question in time.
Relevant Information
You can get this introduction in the following ways:
1. After purchasing hi-target V100 receiver, there will be “V100
GNSS RTK System User Manual” in the instrument container
to guide you how to operate instrument.
2. Log in hi-target official website, download the electronic
version introduction in “Download Center” → “Manual” →
“Surveying Products”
Advice
If you have any advice or suggestion on V100, please call us or
Dial the national hotline: [phone]. Your feedback
information will improve the production quality.

Content
VI
Content
Preface......................................................................................................III
Content..................................................................................................... VI
Product Introduction .................................................................................1
1.1. Hardware structure..................................................................2
1.2. Power supply system.................................................................4
1.3. Button operation.......................................................................8
1.4. LED............................................................................................9
1.5. Handheld controller iHand20................................................11
Technical parameters...............................................................................19
Work Modes Introduction.......................................................................24
3.1. Static Mode..............................................................................25
3.1.1. Static data collection..........................................................25
3.1.2. Static data storage and download ......................................27
3.2. Network Rover Mode .............................................................29
3.2.1. Project setting ....................................................................29
3.2.2. Data collection...................................................................43
3.2.3. Stake out ............................................................................48
3.2.4. Data Export........................................................................53
3.2.5. Auto-backup and quickly recover......................................54
3.3. Base Mode with External Radio............................................56
Trouble Shooting......................................................................................58
4.1. Registration procedure...........................................................59
4.2. Firmware upgrade..................................................................61
4.3. Reset operation........................................................................62
Schedule1 factory default parameters.................................................63
Schedule2 Key accessories information...............................................64

Product Introduction
1
Product Introduction
This chapter describes:
Hardware structure
Power supply system
Button operation
LED
Handheld controller iHand20
C H A P T E R
1

Product Introduction
2
1.1. Hardware structure
The product appearance is divided into three parts, upper cover,
bottom cover and control panel.
Figure 1-1-1
Figure 1-1-2
Control panel
Bottom cover
Upper cover
Raised point
Guard collar

V100 GNSS RTK System Getting Started
3
Figure 1-1-3
Connection screw: for the instrument fixed to the base or the
pole.
Battery compartment: for housing lithium battery.
Five-pin socket: for external data linking and external power
supply.
Mini USB socket: for connection to the host and external
devices, upgrade firmware and download the static data, can
also charge or supply electricity to the host.
Protective plug: for dustproof and waterproof.
Notice:
If it is unnecessary to use five-pin socket, and USB
interface, please cover the rubber plug to prevent dust.
Battery compartment
Connection screw
Five-pin socket
Mode
Mini USB socket
Protective plug

Product Introduction
4
1.2. Power supply system
Battery, adapter type
Name
type
lithium battery
BLP-6300S
Power adapter
PSAI10R-050Q
Lithium battery
Figure 1-2-1
Adapter
Figure 1-2-2
Recharge
V100 lithium battery should be charged by PSAI10R-050Q adapter,
about 7 hours of charging time.

V100 GNSS RTK System Getting Started
5
Warning:
1. Only the battery and charger configured by the manufacturer can
be used; the battery must not be thrown into fire or used in metal
short circuit electrode.
2. Stop using when the battery is heating, deformation, liquid
leakage, smelling or other abnormal reactions, please exchange
new battery.
3. Stop using when the battery’s working time has been
Significantly reduced, the battery is aged, please exchange new
battery.
Battery installation and removal
(1) Push up the battery cover button, open battery cover.
Figure 1-2-3
(2) Align battery pole with battery compartment pole, push the
battery to the end and the mental button will upspring.
Battery cover button

Product Introduction
6
Figure 1-2-4
Figure 1-2-5
(3) Close the battery cover.
Removal
Push up the battery cover button to open it, then press the metal
button and remove battery.
Metal button
Battery pole

V100 GNSS RTK System Getting Started
7
Power supply
Power supply mode
Power
supply
Power supply mode
Internal：lithium battery
External：USB, Five-pin socket
External power supply
request
USB socket：DC power 4.2-5.5V/1.5A
Five-pin socket：DC power 6-28V/1A
When external power supply, the host will automatically detect the
voltage of lithium battery and external power supply, and choose
the higher voltage power. As for external power supply, it shall use
the special power specified by Hi-Target.
Notice:
1. The service time of lithium battery will decrease along
with the decrease in temperature and
charging-discharging times increasing. A new 6300mAh
lithium battery can be used for 7 hours of static data
collection or rove work.
2. Please charge the battery within 24 hours after using
up, to extend the service life of battery, or the battery
performance will be damaged.
3. If the battery won't be used for long times, please
charge once every month to extend the service life of
battery.

Product Introduction
8
1.3. Button operation
Most settings and operations of receiver are completed using a
button on control panel.
Figure 1-3-1
Description of power button operation
Operation name
Description
On
Shutdown status, long press the button one second to
boot, all lights are on
Off
Boot status, long press the button three seconds, all
lights double fast flash, release the button
Automatic setting station
Shutdown status, long press the button six seconds,
all lights double fast flash, release the button, the
instrument will automatically set the base station
Operating mode switching
Double-click the button to switch working mode,
double-click each time to switch between static and
RTK mode
Status inquiry
Click power button, power LED flashing times
displays power
Reset motherboard
Boot status, long press the button more than 6
seconds, all lights flash at the same time, release the
button, it will reset motherboard
Power button

V100 GNSS RTK System Getting Started
9
1.4. LED
In different setting mode, it displays the different LED status.
Figure 1-4-1
LED Function Description
LED
Meaning
Power LED
(Green)
Long-term
lighting
Full battery
Power LED
(Yellow)
Long-term
lighting
Full battery voltage: internal battery≥3.9V（100%
power）
Power LED
(Red)
Long-term
lighting
Normal voltage: 6% <internal battery power ≤99%
Slow flash
Low voltage: internal battery≤5%
Fast flash
Power indication: 1-4 flash per minute under the
direction of electricity
1：0％~25％
2：25％~50％
3：50％~75％
4：75％~100％
Network LED
(Green)
Off
Static mode
Long-term
lighting
RTK mode
Power LED
Network LED
Satellite LED

Product Introduction
10
Network LED
(Red)
Slow flash
1. RTK mode: flash as difference data interval
2. Static mode: flash as sampling interval
Fast flash
Static mode, storage space<10MB
Satellite LED
(Green)
Long-term
lighting
Satellite lock
Slow flash
satellites are lost
Three LEDs
Fast flash
Satellite LED, Network LED, Power LED all fast
flash at the same time, when release power button,
the motherboard will be reset.

V100 GNSS RTK System Getting Started
11
1.5. Handheld controller iHand20
Front of handheld controller
The front of iHand20 handheld controller includes touch screen,
keyboard and microphone
Figure 1-5-1
Touch screen: Multipoint capacitive touch screen with touch
pen, which supports Chinese and English input.
Keyboard: Photograph, direction control, switch between
Chinese and English, data collection, volume control, power on,
power off and other functions.
Touch screen
Keyboard
Microphone

Product Introduction
12
Microphone: Internal microphone can be used for field
collection of voice message.
Reverse side of handheld controller
There are camera, battery cover, belt, trumpet, etc. on the reverse
side of iHand20 handheld controller.
Figure 1-5-2
Camera: Used for field collection of image information.
Battery cover: Internal removable lithium battery
NFC module
Camera
Speaker
Battery cover
Belt

V100 GNSS RTK System Getting Started
13
Belt: Connect the belt to prevent sliding down.
Speaker: Conduct real-time voice broadcast for the instrument
operation and status.
Side of handheld controller
Figure 1-5-3
Mini USB: Used for connecting USB data line and iHand20
handheld controller.
Audio port: Used for connecting headphone cable and iHand20
handheld controller.
Warnings:
In case of not using audio port or Mini USB, please close the
rubber cover so as to be waterproof and dustproof.
Waterproof & dustproof rubber cover
Audio port
Mini USB

Product Introduction
14
Handheld controller accessories
Charger
Figure 1-5-4
Battery (Lithium battery: 3.7V /6300mAh)
Figure 1-5-5
Data line
Figure 1-5-6
Connect to the USB port of computer, and used for download of
data Connect to the USB port of charger and used for charging