Hi-Target V200 User manual

V200 GNSS RTK System
User Manual

V200 GNSS System User Manual
Manual Revision
Revision Date
Revision Level
Description
July. 2021
1
V200 GNSS RTK System
User Manual

V200 GNSS System User Manual
V200
GNSS RTK System
User Manual

V200 GNSS System User Manual
I
Preface
Introduction
Welcome to the Hi-Target V200 receiver. This introduction describes how to use this product.
Experience requirement
To help you use the Hi-Target series products better, Hi-Target suggests that you read the instructions
carefully. If you are unfamiliar with the products, please refer to www.hi-target.com.cn
Tips for safe uses
Exclusions
Before using the product, please read these operating instructions carefully, as they will help you to use
it better. Hi-Target Surveying Instrument Co. Ltd assumes no responsibility if you fail to operate the
product according to the instructions, or operate it wrongly because you have misunderstood them.
Hi-Target is committed to constantly perfecting the product’s functions and performance, improving its
service quality, and reserves the right to change these operating instructions without notice.
We have checked the contents of the instructions and the software & hardware without eliminating the
possibility of deviation. The pictures in the operating instructions are for reference only. In the case of
non-conformity with products, the products shall prevail.
Warning: The contents here are generally very important as the wrong
operation may damage the machine. This can lead to the loss of data, or even
break the system and endanger your safety.
Notice: The contents here are special operations and need your special
attention. Please read them carefully.

V200 GNSS System User Manual
II
Technology and service
If you have any technical issues, please call the Hi-Target technology department for help, and we will
answer your question.
Relevant information
You can obtain this introduction by:
Purchasing Hi-Target products: this manual is found in the instrument container and will help you to
operate the instrument.
Logging on to the Hi-Target official website and downloading the electronic version of this introduction
from Partner Center: http://members.hi-target.com.cn/
Advice
If you have any suggestions for this product, please email them to: [e-mail]. Your
feedback information will help us to improve the product and service.

V200 GNSS System User Manual
3
Contents
Preface ...................................................................................................................................................... I
Introduction............................................................................................................................................. I
Experience requirement ............................................................................................................................I
Tips for safe use..................................................................................................................................... I
Exclusions............................................................................................................................................... I
Technology and service......................................................................................................................... II
Relevant information.............................................................................................................................. II
Advice.................................................................................................................................................... II
Contents.................................................................................................................................................. III
Chapter 1 ...............................................................................................................................................1
Overview............................................................................................................................................... 1
1.1 Foreword ......................................................................................................................................... 2
1.2 Features .......................................................................................................................................... 2
1.3 Use and precautions ....................................................................................................................... 2
Chapter 2 ...............................................................................................................................................3
Product introduction............................................................................................................................... 3
2.1 Overall appearance......................................................................................................................... 4
2.1.1 Upper cover .............................................................................................................................. 4
2.1.2 Bottom cover................................................................................................................................4
2.1.3 Control cover............................................................................................................................. 5
2.2 Button & LED................................................................................................................................... 6
2.2.1 Button function.......................................................................................................................... 6
2.2.2 LED........................................................................................................................................... 6
2.3 WEB management system.............................................................................................................. 7
2.3.1 Main menu................................................................................................................................ 7
2.3.2 Information................................................................................................................................ 9
2.3.3 Work mode.............................................................................................................................. 12
2.3.4 File manager........................................................................................................................... 13
2.3.5 Firmware................................................................................................................................ 14
2.3.6 System................................................................................................................................... 15
2.4 Static survey.................................................................................................................................. 17
2.4.1 Static settings.......................................................................................................................... 17
2.4.2 Static data collection steps..................................................................................................... 17

V200 GNSS System User Manual
4
2.5 Tilt survey........................................................................................................................................20
2.5.1 Calibration-free tilt survey....................................................................................................... 20
2.6 Firmware upgrade ....................................................................................................................... 21
2.6.1 Upgrade by USB cable..............................................................................................................21
2.6.2 Upgrade by using the web management system................................................................... 22
Chapter 3..............................................................................................................................................23
Technical specification............................................................................................................................ 23
Chapter 4..............................................................................................................................................26
Accessories and interfaces.................................................................................................................. 26
4.1 Data cable ..................................................................................................................................... 27
4.2 Antenna.............................................................................................................................................27
4.3 Battery ........................................................................................................................................... 27

V200 GNSS System User Manual
1
Chapter 1
Overview
This chapter contains:
- Foreword
- Features
- Use and precautions

V200 GNSS System User Manual
2
1.1 Foreword
V200 GNSS RTK receiver brings superior performance and high efficiency that will support your
fieldwork with reliable solutions. Its deployment of the advanced RTK engine and new-generation IMU
guarantees a 25% performance improvement even in the most demanding environments. Thus you can
count on Hi-Target V200 to provide you with better productivity.
1.2 Features
1. Its more durable and portable with an ultra-light EPP material instrument case.
2. It can bring accurate and reliable results and boost efficient fieldwork with a self-developed built-in
IMU and core algorithm.
3. Equipped with the High-performance Patch Antenna, it both enhances the low elevation angle
tracking capabilities and maintains a high gain for higher elevation satellites.
4. It does not provide overly optimistic coordinate quality and guarantees the high reliability of RTK fixed
positions, improving accuracy better than 8 cm by 20 %.
5. Hi-Fix technology enables both continuous connectivity and quality results.
1.3 Use and precautions
The V200 GNSS receiver is designed to have chemical and impact resistance, but precision instruments
require careful use and maintenance.
In order to ensure the continuous tracking observation of the satellite and quality of the satellite signal,
the space above the station should be as wide as possible, with no obstacles above the 15°elevation
angle. To reduce the interference of various electromagnetic waves on the GNSS satellite signal, there
should be no strong electromagnetic interference within a range of about 200m around the station, such
as TV towers, microwave stations, and high-voltage transmission lines. To avoid or reduce the
occurrence of multipath effects, the station should be away from terrain and features with strong
reflectors, such as high-rise buildings, water, etc.
Notice: The receiver must be within the specified temperature range when it
is used and stored. For detailed requirements, please refer to Chapter 3:
Technical specification.

V200 GNSS System User Manual
3
Chapter 2
Productintroduction
This chapter contains:
- Overall appearance
- Button & LED
- WEB management system
- Static survey
- Tilt survey
- Firmware upgrade

V200 GNSS System User Manual
4
2.1 Overall appearance
The product’s appearanceis dividedinto three parts, including theupper cover, bottom cover andcontrol
panel.
Figure 2-1-1
2.1.1 Upper cover
Figure 2-1-2
2.1.2 Bottom cover
The bottom cover includes the SMA antenna interface, Type-C USB interface.

V200 GNSS System User Manual
5
Notice:
1. If you don’t use the SMA antenna interface and USB interface, please cover
the rubber plug to protect them from dust and water.
2. When the speaker is flooded, the sound may be silent or hoarse, but it will
return to normal after it has dried.
2
3
1
4
Figure 2-1-3
1. SMA antenna interface 2. Connection screw 3. Speaker 4. Type-C USB interface
◇SMA antenna interface: Connect the radio antenna while using the Internal UHF mode.
◇Type-C USB interface: To upgrade the firmware and download static data.
◇Protective plug: Used for dustproof and waterproof sockets.
2.1.3 Control cover
The control panel includes a satellite light, power button and data light.
1
2
3
Figure 2-1-3
1. Satellite LED 2. Power button 3. Data LED

V200 GNSS System User Manual
6
2.2 Button & LED
2.2.1 Button function
Table 2-2-1 Button function description
Function
Description
Power-on
Long press the power button for 1 second.
Power-off
In the power-on state, long press the power button for more than 3 seconds but less
than 6 seconds.
Forcedshutdown
（use when the
devicecrashes）
Press the power button for at least 12 seconds.
Query current status
Press the power button once to voice the product’s current working status.
Resetmotherboard
When the device is powered on, long press the power button for 6 seconds and
release it after hearing the second "dingdong" sound.
Switch working
mode
Double-click the power button to enter the mode switch. After each double-click, switch
to a working mode, and click the power button to confirm it.
One-keysetting
station
When the device is powered off, long press the power button for 6s to turn it on.
2.2.2 LED
Table 2-2-2 LED function description
Function
Status
Description
Power LED(red)
Long-termlighting
When the device is powered off, it is for charging the
device.
OFF
It is not charging nor fully charged.
PowerLED(green)
Flash
The power ≤10%.
Long-termlighting
1. RTK mode: No correction data.
2. Static mode: Sampling has not started.
Flash
1. RTK mode:
Flashes at the frequency of the correction transmit and
receives.
2. Static mode:

V200 GNSS System User Manual
7
Data LED
Sampling interval >1s: Flashes at the sampling interval.
Sampling interval ≤1s: Flashes once per second.
Off
1. RTK mode: No correction data.
2. Static mode: Sampling has not started.
Satellite LED
Long-termlighting
Satellite is tracked.
Flash
Satellite is not tracked.
2.3 WEB management system
V200 has a built-in web management system that can be used to set the receiver's working mode,
data output, as well as view receiver information and satellite information. The receiver’s Wi-Fi name
is its S/N. You can connect it to a controller or phone (the default password is: 12345678) and then
input the IP address 192.168.20.1 into the browser to log onto the web management system.
Note: The web management system can only be visited when the receiver’s Bluetooth isn’t connected.
2.3.1 Main menu
After logging into the web management system, you can click Start to enter the main menu interface.
Each option of the main menu contains drop-down menus.
Figure 2-3-1 Home Figure 2-3-2 Main menu

V200 GNSS System User Manual
8
Figure 2-3-3 Information Figure 2-3-4 Work mode
Figure 2-3-5 File manager Figure 2-3-6 Firmware
Figure 2-3-7 System

V200 GNSS System User Manual
9
Table 2-3-1 Menu description
Main menu
Sub-menu
Description
Information
Device info
Device model, version, registration info, etc.
Position info
Coordinates, satellite tracking, solution state, etc.
Base info
Coordinates and distance to the base
Sky plot
Check the sky plot
Satellites list
Satellite tracking information
Work mode
Rover
Data link and parameter settings of the rover
Base
Data link and parameter settings of the base
Static
Static measurement parameter settings
File manager
Static data
Download, delete and format static data
Firmware
Upgrade
Select and upgrade the firmware
Restore
Restore the system
System
Constellation
The satellite tracking switches
Five-pin port
Output settings of the five-pin
Radio
Radio frequency list
Reset
Reset the motherboard
Registration
Device registration and information
Others
Switch of the static RINEX and volume control, etc
2.3.2 Information
1. Device information
Includes the main information about the device: device model, S/N, firmware version, OEM info,
battery power, work mode, configuration parameters, etc.
Figure 2-3-8 Device information

V200 GNSS System User Manual
10

V200 GNSS System User Manual
11
2. Position information
Includes the device’s position, satellites, solution state, latency, PDOP and time, etc.
Figure 2-3-9 Position information
3. Base information
Includes the coordinates and distance of the base in the rover mode.
Figure 2-3-10 Base information
4. Sky plot
Displays the visual satellites of the device and the switches of each constellation.

V200 GNSS System User Manual
12
Figure 2-3-11 Sky plot
5. Satellites list
Shows the satellite’s tracked information.
Figure 2-3-12 Satellites list
2.3.3 Work mode
1. Rover
Set up the rover’s data link and parameters. The rover station data link includes: Internal UHF.
Figure 2-3-13 Rover
2. Base
Set up the data link and parameters of the base and get the point coordinates by averaging. The base
station data link mode includes: Internal UHF.

V200 GNSS System User Manual
13
Figure 2-3-14 Base
3. Static
Set up the file name and parameters of the static collection.
Note: After ticking Static Mode, you can only cancel it in the base rover setting interface.
Figure 2-3-15 Static
2.3.4 File manager
1. Static data
Display the static data files, which supports the Download, Delete and Format options.
Note: After checking the "Static Mode", you can only uncheck the "Static Mode" in the base station
mode or rover mode.