HIK VISION DS-PD2-T12P-WEL User manual

EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG)2
Environmental Class(EC)IV
DS-PD2-T12P-WEL
12m Wireless Outdoor Detector
Diagram References
ENGLISH
Baery Informaon
1
2
3
4
5
6
7
8
Installation
Ensure that t he detector is installed away from reflected sunlight and large
objects.
Switches
If you disable the detector’s LEDs, you can remotely enable them in walk tests.
Microwave range and angle of detection
Use the highlighted dials to change the microwave range and angle
of detecon.
LEDs
Four LEDs show the status of the detector.
Lens inserts
Use lens inserts to control the coverage area.
Registration procedure
Aer powering up and aer registraon,there is a 10 minute mer that allows
a walk test of the PIR and microwave sensors.You can set up the sensivity and
microwave range without using the control panel to perform a walk test.Aer
10 minutes,the detector enters sleep mode. Please register the device within
90 seconds aer it being powered on.
Register Locally
1.Make the security control panel enter the registraon mode.
2. Register the detector: Hold the registraon key unl the three LEDs flash
alternately. The green LED will flash 8 mes if the registraon is finished.
3. Communicaon Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector should
be less than 50 cm.
Initialize the Detector
1. Remove the baery to power the detector off.
2. 5s later, hold the registraon key and reinstall the baery to power the
detector on at the same me to make the three LEDs start flashing alternately.
Release the registraon key while the three LEDs flash once together.
Signal strength test
Enter the signal checking mode by operang on the control panel
Indicator turns green:Strong Signal.
Indicator turns red:Weak Signal.
Bracket tamper signal input
The baeries supplied with this product have been chosen to provide long service life whilst, for safety
reasons, having limited output current.The baery leads must be connected for operaon. When disposing
of the product, remove the baeries and disposed of separately in accordance with the local regulaons.
Detectors Technical Characteriscs
Detecon Range
Detecon Angle
Detecon Zones
Detecon Speed
Mounng Height
Two-way Wireless Technology
Blue Wave Technology
Dual Element Pyroelectric Sensor
Tamper Protecon
Intergrated Walk Test Buzzer
Separated LED Indicaon:
Orange(Microwave),Blue(Alarm),Green(PIR)
Signal Strength Indicators (SSI)
3 Microwave Frequencies to Avoid Interference
Digital Independent Floang Threshold(IFT) Technology
Plasc Housing
Animal Immunity
Opcs
Adjustable Sensivity
Lens
Detecon Method
Sensor
Weatherproof
Cerfied Operang Temperature
Physical Dimensions(H x W x D)
Weight
Baery Type
Baery Life
Baery Capacity
Rotatable Wall Mounted
Fixed Wall Mounted
Ceiling Mounted
Baery
12m
90°
2x22 zones
0.25–2.5 m/s
1-1.5 m
Yes
Yes
Yes
Front, rear, and bracket tamper signal input
Yes
Top: Microwave, PIR 1 and alarm
Boom: PIR 2
Yes
Yes
Yes
3mm polycarbonate
Up to 24kg
Dual-vision sealed opcs
High or low range
UV compensated
Tri-Signal Detecon Logic
2 low noise dual element passive infrared sensors and a microwave doppler unit
IP55 rated
-25℃to +60℃(Cerfied)
118mm x 77mm x 84mm
0.3kg
2x3V 4700mAh Lithium baery packs
Up to 3 years
4700mAh
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional baery available separately
Electrical & baery
Environmental and Operang Features
Accessories
Technical Specification
Battery Information
1
2
45
3
ON posion
LEDs on
Buzzer on
Top PIR high sensivity
Boom PIR high sensivity
1
2
3
4
OFF posion
LEDs off
Buzzer off
Top PIR low sensivity
Boom PIR low sensivity

EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG)2
Environmental Class(EC)IV
DS-PD2-T12P-WEL
12m Wireless Outdoor Detector
Diagram References
ENGLISH
Baery Informaon
1
2
3
4
5
6
7
8
Installation
Ensure that t he detector is installed away from reflected sunlight and large
objects.
Switches
If you disable the detector’s LEDs, you can remotely enable them in walk tests.
Microwave range and angle of detection
Use the highlighted dials to change the microwave range and angle
of detecon.
LEDs
Four LEDs show the status of the detector.
Lens inserts
Use lens inserts to control the coverage area.
Registration procedure
Aer powering up and aer registraon,there is a 10 minute mer that allows
a walk test of the PIR and microwave sensors.You can set up the sensivity and
microwave range without using the control panel to perform a walk test.Aer
10 minutes,the detector enters sleep mode. Please register the device within
90 seconds aer it being powered on.
Register Locally
1.Make the security control panel enter the registraon mode.
2. Register the detector: Hold the registraon key unl the three LEDs flash
alternately. The green LED will flash 8 mes if the registraon is finished.
3. Communicaon Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector should
be less than 50 cm.
Initialize the Detector
1. Remove the baery to power the detector off.
2. 5s later, hold the registraon key and reinstall the baery to power the
detector on at the same me to make the three LEDs start flashing alternately.
Release the registraon key while the three LEDs flash once together.
Signal strength test
Enter the signal checking mode by operang on the control panel
Indicator turns green:Strong Signal.
Indicator turns red:Weak Signal.
Bracket tamper signal input
The baeries supplied with this product have been chosen to provide long service life whilst, for safety
reasons, having limited output current.The baery leads must be connected for operaon. When disposing
of the product, remove the baeries and disposed of separately in accordance with the local regulaons.
Detectors Technical Characteriscs
Detecon Range
Detecon Angle
Detecon Zones
Detecon Speed
Mounng Height
Two-way Wireless Technology
Blue Wave Technology
Dual Element Pyroelectric Sensor
Tamper Protecon
Intergrated Walk Test Buzzer
Separated LED Indicaon:
Orange(Microwave),Blue(Alarm),Green(PIR)
Signal Strength Indicators (SSI)
3 Microwave Frequencies to Avoid Interference
Digital Independent Floang Threshold(IFT) Technology
Plasc Housing
Animal Immunity
Opcs
Adjustable Sensivity
Lens
Detecon Method
Sensor
Weatherproof
Cerfied Operang Temperature
Physical Dimensions(H x W x D)
Weight
Baery Type
Baery Life
Baery Capacity
Rotatable Wall Mounted
Fixed Wall Mounted
Ceiling Mounted
Baery
12m
90°
2x22 zones
0.25–2.5 m/s
1-1.5 m
Yes
Yes
Yes
Front, rear, and bracket tamper signal input
Yes
Top: Microwave, PIR 1 and alarm
Boom: PIR 2
Yes
Yes
Yes
3mm polycarbonate
Up to 24kg
Dual-vision sealed opcs
High or low range
UV compensated
Tri-Signal Detecon Logic
2 low noise dual element passive infrared sensors and a microwave doppler unit
IP55 rated
-25℃to +60℃(Cerfied)
118mm x 77mm x 84mm
0.3kg
2x3V 4700mAh Lithium baery packs
Up to 3 years
4700mAh
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional baery available separately
Electrical & baery
Environmental and Operang Features
Accessories
Technical Specification
Battery Information
1
2
45
3
ON posion
LEDs on
Buzzer on
Top PIR high sensivity
Boom PIR high sensivity
1
2
3
4
OFF posion
LEDs off
Buzzer off
Top PIR low sensivity
Boom PIR low sensivity

EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG)2
Environmental Class(EC)IV
DS-PD2-T12P-WEL
12m Wireless Outdoor Detector
Diagram References
ENGLISH
Baery Informaon
1
2
3
4
5
6
7
8
Installation
Ensure that t he detector is installed away from reflected sunlight and large
objects.
Switches
If you disable the detector’s LEDs, you can remotely enable them in walk tests.
Microwave range and angle of detection
Use the highlighted dials to change the microwave range and angle
of detecon.
LEDs
Four LEDs show the status of the detector.
Lens inserts
Use lens inserts to control the coverage area.
Registration procedure
Aer powering up and aer registraon,there is a 10 minute mer that allows
a walk test of the PIR and microwave sensors.You can set up the sensivity and
microwave range without using the control panel to perform a walk test.Aer
10 minutes,the detector enters sleep mode. Please register the device within
90 seconds aer it being powered on.
Register Locally
1.Make the security control panel enter the registraon mode.
2. Register the detector: Hold the registraon key unl the three LEDs flash
alternately. The green LED will flash 8 mes if the registraon is finished.
3. Communicaon Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector should
be less than 50 cm.
Initialize the Detector
1. Remove the baery to power the detector off.
2. 5s later, hold the registraon key and reinstall the baery to power the
detector on at the same me to make the three LEDs start flashing alternately.
Release the registraon key while the three LEDs flash once together.
Signal strength test
Enter the signal checking mode by operang on the control panel
Indicator turns green:Strong Signal.
Indicator turns red:Weak Signal.
Bracket tamper signal input
The baeries supplied with this product have been chosen to provide long service life whilst, for safety
reasons, having limited output current.The baery leads must be connected for operaon. When disposing
of the product, remove the baeries and disposed of separately in accordance with the local regulaons.
Detectors Technical Characteriscs
Detecon Range
Detecon Angle
Detecon Zones
Detecon Speed
Mounng Height
Two-way Wireless Technology
Blue Wave Technology
Dual Element Pyroelectric Sensor
Tamper Protecon
Intergrated Walk Test Buzzer
Separated LED Indicaon:
Orange(Microwave),Blue(Alarm),Green(PIR)
Signal Strength Indicators (SSI)
3 Microwave Frequencies to Avoid Interference
Digital Independent Floang Threshold(IFT) Technology
Plasc Housing
Animal Immunity
Opcs
Adjustable Sensivity
Lens
Detecon Method
Sensor
Weatherproof
Cerfied Operang Temperature
Physical Dimensions(H x W x D)
Weight
Baery Type
Baery Life
Baery Capacity
Rotatable Wall Mounted
Fixed Wall Mounted
Ceiling Mounted
Baery
12m
90°
2x22 zones
0.25–2.5 m/s
1-1.5 m
Yes
Yes
Yes
Front, rear, and bracket tamper signal input
Yes
Top: Microwave, PIR 1 and alarm
Boom: PIR 2
Yes
Yes
Yes
3mm polycarbonate
Up to 24kg
Dual-vision sealed opcs
High or low range
UV compensated
Tri-Signal Detecon Logic
2 low noise dual element passive infrared sensors and a microwave doppler unit
IP55 rated
-25℃to +60℃(Cerfied)
118mm x 77mm x 84mm
0.3kg
2x3V 4700mAh Lithium baery packs
Up to 3 years
4700mAh
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional baery available separately
Electrical & baery
Environmental and Operang Features
Accessories
Technical Specification
Battery Information
1
2
45
3
ON posion
LEDs on
Buzzer on
Top PIR high sensivity
Boom PIR high sensivity
1
2
3
4
OFF posion
LEDs off
Buzzer off
Top PIR low sensivity
Boom PIR low sensivity

EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG)2
Environmental Class(EC)IV
DS-PD2-T12P-WEL
12m Wireless Outdoor Detector
Diagram References
ENGLISH
Baery Informaon
1
2
3
4
5
6
7
8
Installation
Ensure that t he detector is installed away from reflected sunlight and large
objects.
Switches
If you disable the detector’s LEDs, you can remotely enable them in walk tests.
Microwave range and angle of detection
Use the highlighted dials to change the microwave range and angle
of detecon.
LEDs
Four LEDs show the status of the detector.
Lens inserts
Use lens inserts to control the coverage area.
Registration procedure
Aer powering up and aer registraon,there is a 10 minute mer that allows
a walk test of the PIR and microwave sensors.You can set up the sensivity and
microwave range without using the control panel to perform a walk test.Aer
10 minutes,the detector enters sleep mode. Please register the device within
90 seconds aer it being powered on.
Register Locally
1.Make the security control panel enter the registraon mode.
2. Register the detector: Hold the registraon key unl the three LEDs flash
alternately. The green LED will flash 8 mes if the registraon is finished.
3. Communicaon Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector should
be less than 50 cm.
Initialize the Detector
1. Remove the baery to power the detector off.
2. 5s later, hold the registraon key and reinstall the baery to power the
detector on at the same me to make the three LEDs start flashing alternately.
Release the registraon key while the three LEDs flash once together.
Signal strength test
Enter the signal checking mode by operang on the control panel
Indicator turns green:Strong Signal.
Indicator turns red:Weak Signal.
Bracket tamper signal input
The baeries supplied with this product have been chosen to provide long service life whilst, for safety
reasons, having limited output current.The baery leads must be connected for operaon. When disposing
of the product, remove the baeries and disposed of separately in accordance with the local regulaons.
Detectors Technical Characteriscs
Detecon Range
Detecon Angle
Detecon Zones
Detecon Speed
Mounng Height
Two-way Wireless Technology
Blue Wave Technology
Dual Element Pyroelectric Sensor
Tamper Protecon
Intergrated Walk Test Buzzer
Separated LED Indicaon:
Orange(Microwave),Blue(Alarm),Green(PIR)
Signal Strength Indicators (SSI)
3 Microwave Frequencies to Avoid Interference
Digital Independent Floang Threshold(IFT) Technology
Plasc Housing
Animal Immunity
Opcs
Adjustable Sensivity
Lens
Detecon Method
Sensor
Weatherproof
Cerfied Operang Temperature
Physical Dimensions(H x W x D)
Weight
Baery Type
Baery Life
Baery Capacity
Rotatable Wall Mounted
Fixed Wall Mounted
Ceiling Mounted
Baery
12m
90°
2x22 zones
0.25–2.5 m/s
1-1.5 m
Yes
Yes
Yes
Front, rear, and bracket tamper signal input
Yes
Top: Microwave, PIR 1 and alarm
Boom: PIR 2
Yes
Yes
Yes
3mm polycarbonate
Up to 24kg
Dual-vision sealed opcs
High or low range
UV compensated
Tri-Signal Detecon Logic
2 low noise dual element passive infrared sensors and a microwave doppler unit
IP55 rated
-25℃to +60℃(Cerfied)
118mm x 77mm x 84mm
0.3kg
2x3V 4700mAh Lithium baery packs
Up to 3 years
4700mAh
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional baery available separately
Electrical & baery
Environmental and Operang Features
Accessories
Technical Specification
Battery Information
1
2
45
3
ON posion
LEDs on
Buzzer on
Top PIR high sensivity
Boom PIR high sensivity
1
2
3
4
OFF posion
LEDs off
Buzzer off
Top PIR low sensivity
Boom PIR low sensivity

EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG)2
Environmental Class(EC)IV
DS-PD2-T12P-WEL
12m Wireless Outdoor Detector
Diagram References
ENGLISH
Baery Informaon
1
2
3
4
5
6
7
8
Installation
Ensure that t he detector is installed away from reflected sunlight and large
objects.
Switches
If you disable the detector’s LEDs, you can remotely enable them in walk tests.
Microwave range and angle of detection
Use the highlighted dials to change the microwave range and angle
of detecon.
LEDs
Four LEDs show the status of the detector.
Lens inserts
Use lens inserts to control the coverage area.
Registration procedure
Aer powering up and aer registraon,there is a 10 minute mer that allows
a walk test of the PIR and microwave sensors.You can set up the sensivity and
microwave range without using the control panel to perform a walk test.Aer
10 minutes,the detector enters sleep mode. Please register the device within
90 seconds aer it being powered on.
Register Locally
1.Make the security control panel enter the registraon mode.
2. Register the detector: Hold the registraon key unl the three LEDs flash
alternately. The green LED will flash 8 mes if the registraon is finished.
3. Communicaon Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector should
be less than 50 cm.
Initialize the Detector
1. Remove the baery to power the detector off.
2. 5s later, hold the registraon key and reinstall the baery to power the
detector on at the same me to make the three LEDs start flashing alternately.
Release the registraon key while the three LEDs flash once together.
Signal strength test
Enter the signal checking mode by operang on the control panel
Indicator turns green:Strong Signal.
Indicator turns red:Weak Signal.
Bracket tamper signal input
The baeries supplied with this product have been chosen to provide long service life whilst, for safety
reasons, having limited output current.The baery leads must be connected for operaon. When disposing
of the product, remove the baeries and disposed of separately in accordance with the local regulaons.
Detectors Technical Characteriscs
Detecon Range
Detecon Angle
Detecon Zones
Detecon Speed
Mounng Height
Two-way Wireless Technology
Blue Wave Technology
Dual Element Pyroelectric Sensor
Tamper Protecon
Intergrated Walk Test Buzzer
Separated LED Indicaon:
Orange(Microwave),Blue(Alarm),Green(PIR)
Signal Strength Indicators (SSI)
3 Microwave Frequencies to Avoid Interference
Digital Independent Floang Threshold(IFT) Technology
Plasc Housing
Animal Immunity
Opcs
Adjustable Sensivity
Lens
Detecon Method
Sensor
Weatherproof
Cerfied Operang Temperature
Physical Dimensions(H x W x D)
Weight
Baery Type
Baery Life
Baery Capacity
Rotatable Wall Mounted
Fixed Wall Mounted
Ceiling Mounted
Baery
12m
90°
2x22 zones
0.25–2.5 m/s
1-1.5 m
Yes
Yes
Yes
Front, rear, and bracket tamper signal input
Yes
Top: Microwave, PIR 1 and alarm
Boom: PIR 2
Yes
Yes
Yes
3mm polycarbonate
Up to 24kg
Dual-vision sealed opcs
High or low range
UV compensated
Tri-Signal Detecon Logic
2 low noise dual element passive infrared sensors and a microwave doppler unit
IP55 rated
-25℃to +60℃(Cerfied)
118mm x 77mm x 84mm
0.3kg
2x3V 4700mAh Lithium baery packs
Up to 3 years
4700mAh
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional baery available separately
Electrical & baery
Environmental and Operang Features
Accessories
Technical Specification
Battery Information
1
2
45
3
ON posion
LEDs on
Buzzer on
Top PIR high sensivity
Boom PIR high sensivity
1
2
3
4
OFF posion
LEDs off
Buzzer off
Top PIR low sensivity
Boom PIR low sensivity

EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG)2
Environmental Class(EC)IV
DS-PD2-T12P-WEL
12m Wireless Outdoor Detector
Diagram References
ENGLISH
Baery Informaon
1
2
3
4
5
6
7
8
Installation
Ensure that t he detector is installed away from reflected sunlight and large
objects.
Switches
If you disable the detector’s LEDs, you can remotely enable them in walk tests.
Microwave range and angle of detection
Use the highlighted dials to change the microwave range and angle
of detecon.
LEDs
Four LEDs show the status of the detector.
Lens inserts
Use lens inserts to control the coverage area.
Registration procedure
Aer powering up and aer registraon,there is a 10 minute mer that allows
a walk test of the PIR and microwave sensors.You can set up the sensivity and
microwave range without using the control panel to perform a walk test.Aer
10 minutes,the detector enters sleep mode. Please register the device within
90 seconds aer it being powered on.
Register Locally
1.Make the security control panel enter the registraon mode.
2. Register the detector: Hold the registraon key unl the three LEDs flash
alternately. The green LED will flash 8 mes if the registraon is finished.
3. Communicaon Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector should
be less than 50 cm.
Initialize the Detector
1. Remove the baery to power the detector off.
2. 5s later, hold the registraon key and reinstall the baery to power the
detector on at the same me to make the three LEDs start flashing alternately.
Release the registraon key while the three LEDs flash once together.
Signal strength test
Enter the signal checking mode by operang on the control panel
Indicator turns green:Strong Signal.
Indicator turns red:Weak Signal.
Bracket tamper signal input
The baeries supplied with this product have been chosen to provide long service life whilst, for safety
reasons, having limited output current.The baery leads must be connected for operaon. When disposing
of the product, remove the baeries and disposed of separately in accordance with the local regulaons.
Detectors Technical Characteriscs
Detecon Range
Detecon Angle
Detecon Zones
Detecon Speed
Mounng Height
Two-way Wireless Technology
Blue Wave Technology
Dual Element Pyroelectric Sensor
Tamper Protecon
Intergrated Walk Test Buzzer
Separated LED Indicaon:
Orange(Microwave),Blue(Alarm),Green(PIR)
Signal Strength Indicators (SSI)
3 Microwave Frequencies to Avoid Interference
Digital Independent Floang Threshold(IFT) Technology
Plasc Housing
Animal Immunity
Opcs
Adjustable Sensivity
Lens
Detecon Method
Sensor
Weatherproof
Cerfied Operang Temperature
Physical Dimensions(H x W x D)
Weight
Baery Type
Baery Life
Baery Capacity
Rotatable Wall Mounted
Fixed Wall Mounted
Ceiling Mounted
Baery
12m
90°
2x22 zones
0.25–2.5 m/s
1-1.5 m
Yes
Yes
Yes
Front, rear, and bracket tamper signal input
Yes
Top: Microwave, PIR 1 and alarm
Boom: PIR 2
Yes
Yes
Yes
3mm polycarbonate
Up to 24kg
Dual-vision sealed opcs
High or low range
UV compensated
Tri-Signal Detecon Logic
2 low noise dual element passive infrared sensors and a microwave doppler unit
IP55 rated
-25℃to +60℃(Cerfied)
118mm x 77mm x 84mm
0.3kg
2x3V 4700mAh Lithium baery packs
Up to 3 years
4700mAh
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional baery available separately
Electrical & baery
Environmental and Operang Features
Accessories
Technical Specification
Battery Information
1
2
45
3
ON posion
LEDs on
Buzzer on
Top PIR high sensivity
Boom PIR high sensivity
1
2
3
4
OFF posion
LEDs off
Buzzer off
Top PIR low sensivity
Boom PIR low sensivity

EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG)2
Environmental Class(EC)IV
DS-PD2-T12P-WEL
12m Wireless Outdoor Detector
Diagram References
ENGLISH
Baery Informaon
1
2
3
4
5
6
7
8
Installation
Ensure that t he detector is installed away from reflected sunlight and large
objects.
Switches
If you disable the detector’s LEDs, you can remotely enable them in walk tests.
Microwave range and angle of detection
Use the highlighted dials to change the microwave range and angle
of detecon.
LEDs
Four LEDs show the status of the detector.
Lens inserts
Use lens inserts to control the coverage area.
Registration procedure
Aer powering up and aer registraon,there is a 10 minute mer that allows
a walk test of the PIR and microwave sensors.You can set up the sensivity and
microwave range without using the control panel to perform a walk test.Aer
10 minutes,the detector enters sleep mode. Please register the device within
90 seconds aer it being powered on.
Register Locally
1.Make the security control panel enter the registraon mode.
2. Register the detector: Hold the registraon key unl the three LEDs flash
alternately. The green LED will flash 8 mes if the registraon is finished.
3. Communicaon Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector should
be less than 50 cm.
Initialize the Detector
1. Remove the baery to power the detector off.
2. 5s later, hold the registraon key and reinstall the baery to power the
detector on at the same me to make the three LEDs start flashing alternately.
Release the registraon key while the three LEDs flash once together.
Signal strength test
Enter the signal checking mode by operang on the control panel
Indicator turns green:Strong Signal.
Indicator turns red:Weak Signal.
Bracket tamper signal input
The baeries supplied with this product have been chosen to provide long service life whilst, for safety
reasons, having limited output current.The baery leads must be connected for operaon. When disposing
of the product, remove the baeries and disposed of separately in accordance with the local regulaons.
Detectors Technical Characteriscs
Detecon Range
Detecon Angle
Detecon Zones
Detecon Speed
Mounng Height
Two-way Wireless Technology
Blue Wave Technology
Dual Element Pyroelectric Sensor
Tamper Protecon
Intergrated Walk Test Buzzer
Separated LED Indicaon:
Orange(Microwave),Blue(Alarm),Green(PIR)
Signal Strength Indicators (SSI)
3 Microwave Frequencies to Avoid Interference
Digital Independent Floang Threshold(IFT) Technology
Plasc Housing
Animal Immunity
Opcs
Adjustable Sensivity
Lens
Detecon Method
Sensor
Weatherproof
Cerfied Operang Temperature
Physical Dimensions(H x W x D)
Weight
Baery Type
Baery Life
Baery Capacity
Rotatable Wall Mounted
Fixed Wall Mounted
Ceiling Mounted
Baery
12m
90°
2x22 zones
0.25–2.5 m/s
1-1.5 m
Yes
Yes
Yes
Front, rear, and bracket tamper signal input
Yes
Top: Microwave, PIR 1 and alarm
Boom: PIR 2
Yes
Yes
Yes
3mm polycarbonate
Up to 24kg
Dual-vision sealed opcs
High or low range
UV compensated
Tri-Signal Detecon Logic
2 low noise dual element passive infrared sensors and a microwave doppler unit
IP55 rated
-25℃to +60℃(Cerfied)
118mm x 77mm x 84mm
0.3kg
2x3V 4700mAh Lithium baery packs
Up to 3 years
4700mAh
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional baery available separately
Electrical & baery
Environmental and Operang Features
Accessories
Technical Specification
Battery Information
1
2
45
3
ON posion
LEDs on
Buzzer on
Top PIR high sensivity
Boom PIR high sensivity
1
2
3
4
OFF posion
LEDs off
Buzzer off
Top PIR low sensivity
Boom PIR low sensivity

User Manual
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co.,Ltd.
ALL RIGHTS RESERVED.
Any and all informaon, including, among others, wordings, pictures, graphs are the properes of Hangzhou Hikvision Digital
Technology Co., Ltd. or its subsidiaries (hereinaer referred to be “Hikvision”). This user manual (hereinaer referred to be
“the Manual”) cannot be reproduced, changed, translated, or distributed, parally or wholly, by any means, without the prior
wrien permission of Hikvision. Unless otherwise spulated, Hikvision does not make any warranes, guarantees or representaons,
express or implied, regarding to the Manual.
About this Manual
This manual is applicable to detector.
The Manual includes instrucons for using and managing the product.
Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon contained in the
Manual is subject to change, without noce, due to firmware updates or other reasons.
Please find the latest version in the company website (hp://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and
logos menoned below are the properes of their respecve owners.
This product and - if applicable - the supplied accessories
too are marked with“CE”and comply therefore with the
applicable harmonized European standards listed under
the RE Direcve 2014/53/EU, the RoHS Direcve 2011/65/EU.
For electrical products sold within the European Community.
At the end of the electrical products life,it should not be
disposed of with household waste. Please recycle where
facilies exist. Check with your local Authority or retailer for
recycling advice in your country.
This product operates in a
European non-harmonised
frequency band
678
Product Information

User Manual
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co.,Ltd.
ALL RIGHTS RESERVED.
Any and all informaon, including, among others, wordings, pictures, graphs are the properes of Hangzhou Hikvision Digital
Technology Co., Ltd. or its subsidiaries (hereinaer referred to be “Hikvision”). This user manual (hereinaer referred to be
“the Manual”) cannot be reproduced, changed, translated, or distributed, parally or wholly, by any means, without the prior
wrien permission of Hikvision. Unless otherwise spulated, Hikvision does not make any warranes, guarantees or representaons,
express or implied, regarding to the Manual.
About this Manual
This manual is applicable to detector.
The Manual includes instrucons for using and managing the product.
Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon contained in the
Manual is subject to change, without noce, due to firmware updates or other reasons.
Please find the latest version in the company website (hp://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and
logos menoned below are the properes of their respecve owners.
This product and - if applicable - the supplied accessories
too are marked with“CE”and comply therefore with the
applicable harmonized European standards listed under
the RE Direcve 2014/53/EU, the RoHS Direcve 2011/65/EU.
For electrical products sold within the European Community.
At the end of the electrical products life,it should not be
disposed of with household waste. Please recycle where
facilies exist. Check with your local Authority or retailer for
recycling advice in your country.
This product operates in a
European non-harmonised
frequency band
678
Product Information

User Manual
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co.,Ltd.
ALL RIGHTS RESERVED.
Any and all informaon, including, among others, wordings, pictures, graphs are the properes of Hangzhou Hikvision Digital
Technology Co., Ltd. or its subsidiaries (hereinaer referred to be “Hikvision”). This user manual (hereinaer referred to be
“the Manual”) cannot be reproduced, changed, translated, or distributed, parally or wholly, by any means, without the prior
wrien permission of Hikvision. Unless otherwise spulated, Hikvision does not make any warranes, guarantees or representaons,
express or implied, regarding to the Manual.
About this Manual
This manual is applicable to detector.
The Manual includes instrucons for using and managing the product.
Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon contained in the
Manual is subject to change, without noce, due to firmware updates or other reasons.
Please find the latest version in the company website (hp://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and
logos menoned below are the properes of their respecve owners.
This product and - if applicable - the supplied accessories
too are marked with“CE”and comply therefore with the
applicable harmonized European standards listed under
the RE Direcve 2014/53/EU, the RoHS Direcve 2011/65/EU.
For electrical products sold within the European Community.
At the end of the electrical products life,it should not be
disposed of with household waste. Please recycle where
facilies exist. Check with your local Authority or retailer for
recycling advice in your country.
This product operates in a
European non-harmonised
frequency band
678
Product Information

EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG)2
Environmental Class(EC)IV
DS-PD2-T12P-WEL
12m Wireless Outdoor Detector
Diagram References
ENGLISH
Baery Informaon
1
2
3
4
5
6
7
8
Installation
Ensure that t he detector is installed away from reflected sunlight and large
objects.
Switches
If you disable the detector’s LEDs, you can remotely enable them in walk tests.
Microwave range and angle of detection
Use the highlighted dials to change the microwave range and angle
of detecon.
LEDs
Four LEDs show the status of the detector.
Lens inserts
Use lens inserts to control the coverage area.
Registration procedure
Aer powering up and aer registraon,there is a 10 minute mer that allows
a walk test of the PIR and microwave sensors.You can set up the sensivity and
microwave range without using the control panel to perform a walk test.Aer
10 minutes,the detector enters sleep mode. Please register the device within
90 seconds aer it being powered on.
Register Locally
1.Make the security control panel enter the registraon mode.
2. Register the detector: Hold the registraon key unl the three LEDs flash
alternately. The green LED will flash 8 mes if the registraon is finished.
3. Communicaon Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector should
be less than 50 cm.
Initialize the Detector
1. Remove the baery to power the detector off.
2. 5s later, hold the registraon key and reinstall the baery to power the
detector on at the same me to make the three LEDs start flashing alternately.
Release the registraon key while the three LEDs flash once together.
Signal strength test
Enter the signal checking mode by operang on the control panel
Indicator turns green:Strong Signal.
Indicator turns red:Weak Signal.
Bracket tamper signal input
The baeries supplied with this product have been chosen to provide long service life whilst, for safety
reasons, having limited output current.The baery leads must be connected for operaon. When disposing
of the product, remove the baeries and disposed of separately in accordance with the local regulaons.
Detectors Technical Characteriscs
Detecon Range
Detecon Angle
Detecon Zones
Detecon Speed
Mounng Height
Two-way Wireless Technology
Blue Wave Technology
Dual Element Pyroelectric Sensor
Tamper Protecon
Intergrated Walk Test Buzzer
Separated LED Indicaon:
Orange(Microwave),Blue(Alarm),Green(PIR)
Signal Strength Indicators (SSI)
3 Microwave Frequencies to Avoid Interference
Digital Independent Floang Threshold(IFT) Technology
Plasc Housing
Animal Immunity
Opcs
Adjustable Sensivity
Lens
Detecon Method
Sensor
Weatherproof
Cerfied Operang Temperature
Physical Dimensions(H x W x D)
Weight
Baery Type
Baery Life
Baery Capacity
Rotatable Wall Mounted
Fixed Wall Mounted
Ceiling Mounted
Baery
12m
90°
2x22 zones
0.25–2.5 m/s
1-1.5 m
Yes
Yes
Yes
Front, rear, and bracket tamper signal input
Yes
Top: Microwave, PIR 1 and alarm
Boom: PIR 2
Yes
Yes
Yes
3mm polycarbonate
Up to 24kg
Dual-vision sealed opcs
High or low range
UV compensated
Tri-Signal Detecon Logic
2 low noise dual element passive infrared sensors and a microwave doppler unit
IP55 rated
-25℃to +60℃(Cerfied)
118mm x 77mm x 84mm
0.3kg
2x3V 4700mAh Lithium baery packs
Up to 3 years
4700mAh
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional wall and fixed brackets available separately
Yes – addional baery available separately
Electrical & baery
Environmental and Operang Features
Accessories
Technical Specification
Battery Information
1
2
45
3
ON posion
LEDs on
Buzzer on
Top PIR high sensivity
Boom PIR high sensivity
1
2
3
4
OFF posion
LEDs off
Buzzer off
Top PIR low sensivity
Boom PIR low sensivity

User Manual
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co.,Ltd.
ALL RIGHTS RESERVED.
Any and all informaon, including, among others, wordings, pictures, graphs are the properes of Hangzhou Hikvision Digital
Technology Co., Ltd. or its subsidiaries (hereinaer referred to be “Hikvision”). This user manual (hereinaer referred to be
“the Manual”) cannot be reproduced, changed, translated, or distributed, parally or wholly, by any means, without the prior
wrien permission of Hikvision. Unless otherwise spulated, Hikvision does not make any warranes, guarantees or representaons,
express or implied, regarding to the Manual.
About this Manual
This manual is applicable to detector.
The Manual includes instrucons for using and managing the product.
Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon contained in the
Manual is subject to change, without noce, due to firmware updates or other reasons.
Please find the latest version in the company website (hp://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and
logos menoned below are the properes of their respecve owners.
This product and - if applicable - the supplied accessories
too are marked with“CE”and comply therefore with the
applicable harmonized European standards listed under
the RE Direcve 2014/53/EU, the RoHS Direcve 2011/65/EU.
For electrical products sold within the European Community.
At the end of the electrical products life,it should not be
disposed of with household waste. Please recycle where
facilies exist. Check with your local Authority or retailer for
recycling advice in your country.
This product operates in a
European non-harmonised
frequency band
678
Product Information

User Manual
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co.,Ltd.
ALL RIGHTS RESERVED.
Any and all informaon, including, among others, wordings, pictures, graphs are the properes of Hangzhou Hikvision Digital
Technology Co., Ltd. or its subsidiaries (hereinaer referred to be “Hikvision”). This user manual (hereinaer referred to be
“the Manual”) cannot be reproduced, changed, translated, or distributed, parally or wholly, by any means, without the prior
wrien permission of Hikvision. Unless otherwise spulated, Hikvision does not make any warranes, guarantees or representaons,
express or implied, regarding to the Manual.
About this Manual
This manual is applicable to detector.
The Manual includes instrucons for using and managing the product.
Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon contained in the
Manual is subject to change, without noce, due to firmware updates or other reasons.
Please find the latest version in the company website (hp://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and
logos menoned below are the properes of their respecve owners.
This product and - if applicable - the supplied accessories
too are marked with“CE”and comply therefore with the
applicable harmonized European standards listed under
the RE Direcve 2014/53/EU, the RoHS Direcve 2011/65/EU.
For electrical products sold within the European Community.
At the end of the electrical products life,it should not be
disposed of with household waste. Please recycle where
facilies exist. Check with your local Authority or retailer for
recycling advice in your country.
This product operates in a
European non-harmonised
frequency band
678
Product Information