Hilti SMD 50 Assembly instructions

Operating instructions en
Mode d’emploi fr
Manual de instrucciones es
SMD 50
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00

1 23 5
543
79
6
8
1
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00

1
2
3
4
2
11
2
3
3
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00

11
9-13
46-57
36-45 26-35
14-25
8
3
9
2
3
3
2
4 5
6
1
2
7
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00

ORIGINAL OPERATING INSTRUCTIONS
SMD 50 magazine
It is essential that the operating instructions
are read before the tool is operated for the
first time.
Always keep these operating instructions to-
gether with the tool.
Ensure that the operating instructions are
with the tool when it is given to other persons.
Contents Page
1 General information 1
2Description 2
3 Accessories 2
4 Spare parts 2
5 Technical data 3
6 Safety instructions 3
7Beforeuse 4
8 Operation 4
9 Care and maintenance 4
10 Disposal 5
11 Manufacturer’s warranty - tools 5
1These numbers refer to the corresponding illustra-
tions. The illustrations can be found on the fold-out cover
pages. Keep these pages open while studying the oper-
ating instructions.
Operating controls and parts of the magazine 1
@Depth gauge
;Screw length adjustment button
=Screw length marks
%Screwdriving depth adjustment thumbwheel
&Release buttons
(Strip guide
)Transport latch
+Lockbutton for sustained operation
§Strip release
1 General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that will lead to
seriousbodilyinjuryorfatality.
WARNING
Draws attention to a potentially dangerous situation that
could lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that
could lead to slight personal injury or damage to the
equipment or other property.
NOTE
Draws attention to an instruction or other useful informa-
tion.
1.2 Explanation of the pictograms and other
information
Warning signs
General
warning
Warning:
electricity
Obligation signs
Wear eye
protection
Wear a hard
hat
Wear ear
protection
Wear
protective
gloves
en
1
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00

Symbols
Return waste
material for
recycling.
Read the
operating
instructions
before use.
Location of identification data on the tool
The type designation and the serial number are stamped
ontherearofthemagazine.Makeanoteofthisdatain
your operating instructions and always refer to it when
making an enquiry to your Hilti representative or service
department.
Type:
Serial no.:
2 Description
2.1 Use of the product as directed
The SMD 50 magazine is an accessory used for driving
collated screws. The magazine is suitable for use with
the Hilti SF 4000 / SF 4000‑A / SD 2500 / SD 4500
/ SD 5000 / SD 5000‑A22 / SD 4500‑A18 and SD 45
screwdrivers. The magazine and Hilti screwdrivers are
optimally matched to each other.
In the safety rules in these operating instructions, the
designation “power tool” refers to the magazine.
Modification of the power tool is not permissible.
Observe the information printed in the operating instruc-
tions concerning operation, care and maintenance.
To avoid the risk of injury, use only genuine Hilti ac-
cessories and insert tools.
The power tool and its ancillary equipment may present
hazards when used incorrectly by untrained personnel or
when used not as directed.
The power tool is designed for professional use and may
be operated, serviced and maintained only by trained,
authorized personnel. This personnel must be informed of
any special hazards that may be encountered. The power
tool and its ancillary equipment may present hazards
when used incorrectly by untrained personnel or when
used not as directed.
The working environment may be as follows: construction
site, workshop, renovation, conversion or new construc-
tion.
Working on materials hazardous to the health (e.g. as-
bestos) is not permissible.
2.2 Items supplied as standard
1Magazine
1 S‑MBL 116 PH2 bit
1 Operating instructions
1 Cardboard box
3 Accessories
Designation
S‑MBL 116 PH2 bit
SME extension
4 Spare parts
SMD 50 magazine 2
2 Magazine unit, complete 382905
3 Depth gauge 288253
4 Magazine spring 387674
en
2
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00

5 Technical data
Right of technical changes reserved.
Magazine SMD 50
Weight Without screwdriver, Without screw strip: 0.35 kg
Length 186 mm
Contact pressure to 40 N (4.0 kp)
Screw capacity (screws per strip) 50
Suitable drywall screw types SMD 50
Length 9…57 mm
Thread inside diameter 3…4.5 mm
Head diameter 7.5…8.6 mm
Drive type Philips no. 2 (S‑MBL 116 PH2)
Philips no. 2 can be driven with the following Hilti
screwdrivers
SF 4000 / SF 4000‑A / SD 5000 / SD 2500 / SD 4500 /
SD 5000‑A22 / SD 4500‑A18 / SD 45
6 Safety instructions
6.1 Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for opera-
tions different from those intended could result in a
hazardous situation.
c) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
f) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
6.2 General safety rules
a) Observe the operating instructions and the safety
rules contained for the magazine and the screw-
driver used.
b) Always work with the screwdriver running at max-
imum speed. Accordingly, use the switch lockbut-
ton on the screwdriver.
c) Do not hold the SMD 50 magazine in the area of
the depth gauge.
d) Each screwdriving stroke must be completed in
full. Interruption of the magazine stroke or release of
pressure half way through the screwdriving operation
may lead to malfunctions.
e) Change the screw strip only when the screwdriver
is switched off.
f) Wear eye protection, especially when working
overhead.
g) Use only genuine Hilti S‑MBL 116 PH2 bits. Check
that the bits are in good condition.
h) Use only genuine Hilti screw strips and screws.
i) Always work at right angles to the surface of the
workpiecetobefastened.
j) Store the screw strips in a straight position, as
they are in the original package.
en
3
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00

7Beforeuse
7.1 Fitting the magazine to the screwdriver 3
CAUTION
Disconnect the screwdriver’s supply cord from the elec-
tric supply before fitting the magazine.
1. Remove the depth gauge and bit holder from the
screwdriver.
2. Fit the bit into the screwdriver.
NOTE The bit clicks into position.
3. Push the magazine onto the screwdriver in the de-
sired working position until it is heard to engage.
NOTE The magazine can be engaged on the tool in
various positions (every 15°).
NOTE Check to ensure that the screwdriver is set
to “forward” rotation.
8Operation
8.1 Screw length adjustment 4
1. Adjust the depth gauge to suit the length of the
screws to be driven.
2. Press the button and slide the depth gauge back or
forward.
3. Setthedepthgaugetooneofthe5lengthmarks
corresponding to the length of the screws.
NOTE The correct screw length setting is very im-
portant for trouble-free magazine operation.
8.2 Inserting the screw strip 5
1. Slide the screw strip through the guide and the
channel until the first screw is in position at the mark
or until the end of the strip is flush with the upper
surface of the magazine at the exit opening.
2. Check that the screw strip has engaged by trying to
pull it back gently.
8.3 Setting the optimum screwdriving depth 6
1. Set the optimum screwdriving depth by turning the
thumbwheel.
2. Turning the thumbwheel counterclockwise causes
the screw to be driven deeper.
3. Drive a screw to test the screwdriving depth setting.
Readjust the setting if necessary.
NOTE Each audible click of the thumbwheel corres-
ponds to an adjustment of 0.2 mm (0.008 inch).
Turning the thumbwheel clockwise causes the screw
to be driven less deeply.
8.4 Moving the screw strip back 7
CAUTION
Disconnect the screwdriver’s supply cord from the elec-
tric supply.
1. Release the strip retainer by pressing the transport
latch.
2. Pull the screw strip back.
NOTE Alternatively, the screw strip can be pulled
upwards, out of the magazine, without pressing the
transport latch.
8.5 Removing the magazine from the
screwdriver 8
CAUTION
Disconnect the screwdriver’s supply cord from the elec-
tric supply before removing the magazine.
The magazine can be removed by pressing the release
buttons and, at the same time, pulling it away from the
screwdriver.
9 Care and maintenance
9.1 Care of the magazine
NOTE
Dirt and dust (especially from plaster) may have an ad-
verse effect on operation of the magazine.
CAUTION
Do not, under any circumstances, lubricate the
magazine with mineral oil / grease or graphite
sprays. This would increase the risk of malfunctions.
Clean the magazine simply by blowing out the dirt and
dust with compressed air.
9.1.1 Dismantling the magazine for cleaning after
heavy use 9
NOTE
It is recommended that the magazine is cleaned by wash-
ing it out with warm water after a long period of heavy
use.
1. Remove the screw strip as described in the section
“Moving the screw strip back”.
2. Remove the magazine as described in the section
“Removing the magazine from the screwdriver”.
en
4
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00

3. Press the release spring together with the aid of
pliers or a similar tool. The transport mechanism,
including the depth gauge, can then be removed
from the casing. You now have three assemblies in
your hand: the transport mechanism, the pressure
spring and the casing.
4. If necessary, the depth gauge can also be separated
from the other parts by pulling it out while pressing
the screw length adjustment button.
NOTE Take care to avoid pinching your fingers.
5. The parts can then be cleaned thoroughly with warm
water.
NOTE We recommend use of a nylon brush (an old
toothbrush) to remove stubborn deposits.
9.1.2 Assembly after cleaning
Assembly is carried out in the reverse order.
Operate the transport movement once or twice to check
that the magazine is functioning correctly after cleaning
and reassembly.
10 Disposal
Most of the materials from which Hilti tools or appliances are manufactured can be recycled. The materials must
be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for
taking back old tools and appliances for recycling. Ask Hilti customer service or your Hilti representative for further
information.
11 Manufacturer’s warranty - tools
Hilti warrants that the tool supplied is free of defects in
materialandworkmanship.Thiswarrantyisvalidsolong
as the tool is operated and handled correctly, cleaned
and serviced properly and in accordance with the Hilti
Operating Instructions, and the technical system is main-
tained. This means that only original Hilti consumables,
components and spare parts may be used in the tool.
This warranty provides the free-of-charge repair or re-
placement of defective parts only over the entire lifespan
of the tool. Parts requiring repair or replacement as a
result of normal wear and tear are not covered by this
warranty.
Additional claims are excluded, unless stringent na-
tional rules prohibit such exclusion. In particular, Hilti
is not obligated for direct, indirect, incidental or con-
sequential damages, losses or expenses in connec-
tion with, or by reason of, the use of, or inability to
use the tool for any purpose. Implied warranties of
merchantability or fitness for a particular purpose are
specifically excluded.
For repair or replacement, send the tool or related parts
immediately upon discovery of the defect to the address
of the local Hilti marketing organization provided.
This constitutes Hilti’s entire obligation with regard to
warranty and supersedes all prior or contemporaneous
comments and oral or written agreements concerning
warranties.
en
5
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00

*424721*
424721
Hilti Corporation
LI-9494 Schaan
Tel.: +423 / 234 21 11
Fax:+423 / 234 29 65
www.hilti.com
Hilti = registered trademark of Hilti Corp., Schaan
W 3739 | 0513 | 00-Pos. 3 | 1
Printed in Liechtenstein © 2013
Right of technical and programme changes reserved S. E. & O.424721 / A2
Printed: 07.07.2013 | Doc-Nr: PUB / 5142545 / 000 / 00