Hilti VC 150-6 XE User manual

VC 150-6 X
VC 150-6 XE
VC 150-10 X
VC 150-10 XE
Printed: 22.02.2017 | Doc-Nr: PUB / 5334128 / 000 / 00

Printed: 22.02.2017 | Doc-Nr: PUB / 5334128 / 000 / 00

English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that may occur when handling or using the product. The following signal
words are used in combination with a symbol:
DANGER! Draws attention to an imminent hazard that will lead to serious personal injury or
fatality.
WARNING! Draws attention to a potential hazard that could lead to serious personal injury or
fatality.
CAUTION! Draws attention to a potentially dangerous situation that could lead to minor personal
injury or material damage.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use
Instructions for use and other useful information
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions.
The numbering reflects the sequence of operations shown in the illustrations and may deviate
from the steps described in the text.
Item reference numbers are used in the overview illustration and refer to the numbers used in
the key in the product overview section.
This symbol is intended to draw special attention to certain points when handling the product.
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols are used on the product:
Warning: hot surface
Transport by crane is not permissible.
1.4 Product information
Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained
personnel or if used not in accordance with the intended use.
The type designation and serial number are stated on the rating plate.
▶Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Printed: 22.02.2017 | Doc-Nr: PUB / 5334128 / 000 / 00

2 English
Product information
Wet / dry vacuum cleaner VC 150-6 XE
Generation 01
Serial no.
Product information
Wet / dry vacuum cleaner VC 150-6 | VC 150-10
Generation 02
Serial no.
Product information
Wet / dry vacuum cleaner VC 150-10 XE
Generation 03
Serial no.
1.5 Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives
and standards. A copy of the declaration issued by the certification department can be found at the end of
this documentation.
The technical documentation is filed and stored here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany
2 Safety
2.1 Important safety instructions
WARNING! READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. Failure to follow all the
instructions listed below may result in electric shock, fire and/or serious injury. KEEP THESE INSTRUCTIONS
IN A SAFE PLACE.
2.2 General safety instructions
In addition to the safety instructions given in the various sections of these operating instructions, the following
points must be strictly observed at all times.
▶Read all the instructions. Failure to follow all the instructions listed below may result in electric shock,
fire and/or serious injury.
▶If the appliance is used in conjunction with an electric tool, read and follow the operating
instructions for the electric tool and all the warnings.
▶Modification of the appliance is not permitted.
▶Use the right appliance for the job. Do not use the appliance for purposes for which it was not
intended. Use it only as directed and when in faultless condition.
▶Before beginning work with the appliance, find out how to operate it correctly and about any
hazards associated with the materials it will be picking up and how these materials can be
disposed of.
▶Take the influences of the surrounding area into account. Do not use the appliance where there is
a risk of fire or explosion.
▶The appliance may only be used by persons who are familiar with it, have been trained on how to
use it safely and who understand the resulting hazards. The appliance is not intended for use by
children.
▶Store appliances in a secure place when not in use. When not in use, appliances must be stored
in a dry, high place or locked away out of reach of children.
2.3 Personal safety
▶Stay alert, watch what you are doing and use common sense when working with the product.
Do not use the vacuum cleaner while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating the appliance may result in serious personal injury.
▶The user and any other persons in the vicinity must wear suitable eye protection, a hard hat, ear
protection, protective gloves, safety footwear and breathing protection while the appliance is in
use or while maintenance work on it is being carried out.
Printed: 22.02.2017 | Doc-Nr: PUB / 5334128 / 000 / 00

English 3
▶Engage the wheel brakes so that the vacuum cleaner stands securely. If the wheel brakes are
disengaged the vacuum cleaner may run away out of control.
▶If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of a vacuum cleaner can reduce dust-related hazards.
2.4 Use and care of the appliance
▶Never leave the appliance unattended.
▶Do not deactivate the filter cleaning system when picking up hazardous dusts, especially when
the appliance is used in conjunction with electric tools that generate dust.
▶Protect the appliance from frost.
▶Clean the water level limiting device regularly with a brush, in accordance with the instructions,
and check it for signs of damage.
▶When fitting the top section of the vacuum cleaner, take care to avoid pinching your fingers or
damaging the supply cord. This presents a risk of injury or damage.
▶Check the appliance and its accessories for any damage. Guards, safety devices and any slightly
damaged parts must be checked carefully to ensure that they function faultlessly and as intended.
Check that moving parts function faultlessly, without sticking, and that no parts are damaged. In
order to ensure faultless operation of the appliance, all parts must be fitted correctly and must
meet the necessary requirements.
▶Have the appliance serviced by a qualified repair person using only genuine Hilti spare parts. The
safety of the appliance can thus be maintained.
▶Always unplug the supply cord from the power outlet when the appliance is not in use (during
breaks), before cleaning and maintenance and before changing the filter or accessories. This
preventive safety measure reduces the risk of starting the appliance accidentally.
▶Never pull the vacuum cleaner by the supply cord to a new working position. Do not run the wheels
of the vacuum cleaner over the supply cord.
▶Do not transport the appliance by crane.
2.5 Electrical safety
▶The plug on the supply cord of the appliance must match the outlet. Do not change the plug in any
way. Do not use adapter plugs with earthed (grounded) appliances. Unmodified plugs and matching
outlets reduce risk of electric shock.
▶Insert the plug in a suitable earthed/grounded power outlet which has been correctly and safely
installed and is in compliance with local regulations. If you are in doubt about the effectiveness of
the power outlet’s earth/ground connection, have it checked by a qualified specialist.
▶Avoid body contact with earthed or grounded surfaces such as pipes, radiators, cookers, stoves
and refrigerators. There is an increased risk of electric shock if your body is grounded.
▶Do not expose the appliance to rain or wet conditions. Water entering an electric appliance will
increase the risk of electric shock.
▶Check to ensure that the supply cord does not lie in a puddle of water.
▶Check the appliance’s supply cord at regular intervals and have it replaced by Hilti Service if
damage is found. Check extension cords at regular intervals and replace them if found to be
damaged.
▶Do not touch the supply cord or extension cord if they are damaged while working. Disconnect
the supply cord plug from the power outlet. Damaged supply cords or extension cords present a risk
of electric shock.
▶The electric supply cord may be replaced only with a cord of the type specified in the operating
instructions.
▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the appliance. Keep
the cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
▶When operating an electric appliance outdoors, use only extension cords of a type suitable for
outdoor use. Use of an extension cord suitable for outdoor use reduces the risk of electric shock.
▶In the event of an interruption in the electric supply, switch the appliance off and unplug it from
the power outlet.
▶Use the power outlet on the appliance only for the purposes described in the operating instructions.
▶Never operate the appliance when it is dirty or wet. Dust (especially dust from conductive materials)
or dampness adhering to the surface of the appliance may, under unfavorable conditions, lead to electric
shock. Dirty or dusty appliances should thus be checked by Hilti Service at regular intervals,
especially if used frequently for working on conductive materials.
Printed: 22.02.2017 | Doc-Nr: PUB / 5334128 / 000 / 00