Hisense AVH-09UXCSAA Instruction Manual

Floor-
Concealed
Type
AVH-09UXCSAA
UX
AVH-14UXCSAA
UX
AVH-18UXCSBA
UX
AVH-24UXCSBA
UX
ORIGINAL INSTRUCTIONS
P00426Q

Hisense
Hisense
IMPORTANT NOTICE
Correct Disposal of this product
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use
the return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.

Section2 Installation & Maintenance Manual
10

1
09 14 18 24
l
l
l
The appliance is not to be used by children or
person with reduced physical, sensory or mental
capabilities,or lack of experience and knowledge,
Children should be supervised that they do not
play with the appliance.
The appliance should not be installed in the
laundry.
unless they have been given supervision or
instruction concerning use of the appliance by a
person responsible for their safety.
Btu/h
3
10
-

2

(lower than 50
3
Regarding the instructions of Wired Remote Control
Switch or Wireless Remote Control Switch, read the
operation manual attached to the control switch.
4. Before Operation
5. Operation Method
6. Automatic Control
than 50
snow or ice. If covered, remove it by using hot water
shutdown. Do not start the system immediately after
approximately 12 hours before start-up after long
Supply electrical power to the system for
power supply, it may cause a compressor failure,
because the compressor is not heated well.
Make sure that the outdoor unit is not covered with
).If the water temperature is higher
, it will cause damage to plastic parts.
When the system is started after a shutdown longer
than approximately 3 months, it is recommended that
the system be checked by your service contractor.

4
7. Troubleshooting

5
R410A

6

09~14
7
Ceiling
Outlet
Wall
18~24
At least 250 At least 250
619 At least 1000
At least 50 At least 800
(Maintenance space)
Size
Fig.4.2 Suspension Bolts

09~14
Anchor M10
Washer
8
Duct
Tape
Insulation materials
Outlet
Insulation materials Outlet
18~24
1A
Attached all around
(At least 10mm)
4.3.2 Hanging the IndoorUnit
Prevent the subversion of the machine.
The method for ground installation is shown below.
Fix the unit with bolt in the specified location as
shown in Fig.4.3.
Bolt adjustment hole Anchor bolt fixed position
Size
Nut
Concrete Filling Motar
Fig.4.3 Installation Method
4.3.3 Connecting Supply Duct
The supply duct should be inserted onto the root of
the unit outlet. Thermal insulation should be done
and the junction with the unit should be sealed
with aluminum foil tape.
Insulation materials should be attached all around
the outlet preventing the condensation, when there
is no duct connected.

09~14
9
Liquid pipe Gas pipe
Water tray
24
18
２０２
１６８
７２ １０９
１１３
５８
５０
３３
２５８
３９４
３９７
Flaring Dimension
Perform the flaring work as shown below.
(*)It is impossible to perform the flaring work with
1/2H material. In this case, use an accessory
pipe(with a flare).
ΦＤ
Φａ Ｒ４１０Ａ Ｒ４０７Ｃ
６．３５
９．５３
１２．７
１５．８８
１９．０５
９．１
１３．２
１６．６
１９．７
（ ＊ ）
９．０
１３．０
１６．２
１９．４
２３．３
installation

10

11

12
220-240V~ 50Hz
09~24

2.5 0.75
0.83A
50
63
32
25
16
10
6
31.0~2.5
rrent
1.0~2.5
1.5~4.0
2.5~6.0
10.0~25.0
6.0~16.0
4.0~10.0
0.70A
0.56A
13
and Completely seal the end of conduit tube
with sealing materials.
Run through the cables using conduit tube,
Use an ELB (Electric Leakage Breaker).If not
used ,it will cause an electric shock or a fire.
and Completely seal the end of conduit tube
with sealing materials.
Run through the cables using conduit tube,
Use an ELB (Electric Leakage Breaker).If not
used ,it will cause an electric shock or a fire.
Maximum Cu
09
14
18
24
EN60 335-1 EN60 335-1
1 1
3
The wire sizes marked with *1 in the above table are selected
at the maximum current of the unit according to the European
Standard, EN60335-1.Use the wires which are not lighter than
the ordinary polyvinyl chloride sheathed flexible cord
(code designation H05VV-F).
0.46A
Model
1.0~2.5
3
6
16
10
25
32
50

14
Capacity 09 14 18 24
Setting
Position Set by inserting
Slotted screwdriver
into the groove
Ex.) Set at No.16 Unit
DSW6
Set No.1 Pin ON
RSW1
Set at "6"
Before shipment. DSW6 and RSW1 are set to "0".
Max.64 units are available to set when all the equipment
to be connected are corresponding to Hi-NET.
Max.16 units when the units corresponding/
non-corresponding to Hi-NET are combined.
Setting
Position Set by inserting
Slotted screwdriver
into the groove
Ex.) Set at No.5 Cycle
DSW5
Set All Pins OFF
RSW2
Set at "5"
Before shipment. DSW5 and RSW2 are set to "0".
Max.64 cycles are available to set when all the equipment
to be connected are corresponding to Hi-NET.
Max.16 cycles when the units corresponding/
non-corresponding to Hi-NET are combined.
a
5

15

P00426Q 2012.12 V02
Hisense Corporation
Add: 17,Donghai Xi Road,Qingdao 266071,China