HMS Anybus Communicator CAN PROFINET IRT 2.32 User manual

AAnnyybbuuss®® CCoommmmuunniiccaattoorr™™ CCAANN
PPRROOFFIINNEETT®® IIRRTT ((22..3322))
USER MANUAL
SCM-1202-035 1.2 en-US ENGLISH

Important User Information
Disclaimer
The information in this document is for informational purposes only. Please inform HMS Industrial Networks of any
inaccuracies or omissions found in this document. HMS Industrial Networks disclaims any responsibility or liability
for any errors that may appear in this document.
HMS Industrial Networks reserves the right to modify its products in line with its policy of continuous product
development. The information in this document shall therefore not be construed as a commitment on the part of
HMS Industrial Networks and is subject to change without notice. HMS Industrial Networks makes no commitment
to update or keep current the information in this document.
The data, examples and illustrations found in this document are included for illustrative purposes and are only
intended to help improve understanding of the functionality and handling of the product. In view of the wide range
of possible applications of the product, and because of the many variables and requirements associated with any
particular implementation, HMS Industrial Networks cannot assume responsibility or liability for actual use based on
the data, examples or illustrations included in this document nor for any damages incurred during installation of the
product. Those responsible for the use of the product must acquire sufficient knowledge in order to ensure that the
product is used correctly in their specific application and that the application meets all performance and safety
requirements including any applicable laws, regulations, codes and standards. Further, HMS Industrial Networks will
under no circumstances assume liability or responsibility for any problems that may arise as a result from the use of
undocumented features or functional side effects found outside the documented scope of the product. The effects
caused by any direct or indirect use of such aspects of the product are undefined and may include e.g. compatibility
issues and stability issues.
Anybus®is a registered trademark of HMS Industrial Networks AB. All other trademarks mentioned in this document
are the property of their respective holders.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US
Table of Contents Page
1 Preface ................................................................................................................................. 3
1.1 About This Document .......................................................................................................3
1.2 Document history ............................................................................................................3
1.3 Document Conventions.....................................................................................................4
2 Description .......................................................................................................................... 5
2.1 Introduction....................................................................................................................5
2.2 Data Exchange Model .......................................................................................................6
2.3 PROFINET IRT Protocol......................................................................................................7
2.4 CAN Network Protocol ......................................................................................................8
3 Installation......................................................................................................................... 13
3.1 Installation Overview...................................................................................................... 13
3.2 Connectors and Indicators ............................................................................................... 14
3.3 DIN Rail Mounting.......................................................................................................... 14
3.4 CAN Interface................................................................................................................ 16
3.5 PROFINET Interface ........................................................................................................ 16
3.6 Power Connector ........................................................................................................... 16
3.7 USB Connector .............................................................................................................. 16
3.8 LED Indicators ............................................................................................................... 17
4 Configuration..................................................................................................................... 18
4.1 Configuration Overview................................................................................................... 18
4.2 Network Configuration.................................................................................................... 19
4.3 Web Pages.................................................................................................................... 23
5 Anybus Configuration Manager ....................................................................................... 24
5.1 Main Window................................................................................................................ 24
5.2 Basic Settings ................................................................................................................ 25
6 PROFINET Asset Management.......................................................................................... 27
6.1 Asset Management Record.............................................................................................. 27
6.2 Recording and Reading Data ............................................................................................ 27
6.3 Supported File Formats ................................................................................................... 28
6.4 Supported Asset Management Records.............................................................................. 28
6.5 XML Based Asset Management......................................................................................... 29
6.6 Binary Based Asset Management...................................................................................... 32
6.7 Uploading the Asset Management File to the FTP Server....................................................... 36

Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US
A Technical Data ................................................................................................................... 39
A.1 General Specifications..................................................................................................... 39
A.2 CAN Interface................................................................................................................ 39
A.3 PROFINET IRT Interface ................................................................................................... 39
B Licenses.............................................................................................................................. 40

Preface 3 (42)
1 Preface
1.1 About This Document
This document describes how to install and configure the Anybus Communicator CAN PROFINET
IRT (2.32) gateway.
For additional related documentation and file downloads, please visit www.anybus.com/support.
1.2 Document history
Version Date Description
1.0 2017-02-23 First release
1.1 2017-11-22 Updated for new firmware
1.2 2019-04-11 Added section about PROFINET Asset Management
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Preface 4 (42)
1.3 Document Conventions
Ordered lists are used for instructions that must be carried out in sequence:
1. First do this
2. Then do this
Unordered (bulleted) lists are used for:
• Itemized information
• Instructions that can be carried out in any order
...and for action-result type instructions:
►This action...
→ leads to this result
Bold typeface indicates interactive parts such as connectors and switches on the hardware, or
menus and buttons in a graphical user interface.
Monospaced text is used to indicate program code and other
kinds of data input/output such as configuration scripts.
This is a cross-reference within this document: Document Conventions, p. 4
This is an external link (URL): www.hms-networks.com
This is additional information which may facilitate installation and/or operation.
This instruction must be followed to avoid a risk of reduced functionality and/or damage
to the equipment, or to avoid a network security risk.
Caution
This instruction must be followed to avoid a risk of personal injury.
WARNING
This instruction must be followed to avoid a risk of death or serious injury.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Description 5 (42)
2 Description
2.1 Introduction
Anybus Communicator CAN PROFINET IRT (2.32) is designed to exchange data between a CAN
subnetwork and a higher level network. The CAN protocol uses individually configurable frames,
offering great flexibility. Through the configuration of CAN frames, the Anybus Communicator
CAN will adapt to a predefined CAN subnetwork. It will be possible to send data to and receive
data from the CAN subnetwork, but also to act as a relay for data on the subnetwork.
The gateway can issue frames cyclically, on change of data, or based on trigger events issued by
the control system of the higher level network. It can also monitor communication on the
subnetwork and notify the higher level network when data has changed.
Anybus Communicator gateways are configured using Anybus Configuration Manager, a family of
configuration tools that have an easy to use graphical interface and that do not require
programming skills.
Anybus Configuration Manager and additional related software and documentation are available
at www.anybus.com/support.
Fig. 1 Anybus Configuration Manager
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Description 6 (42)
2.2 Data Exchange Model
2.2.1 Overview
The data exchanged on the CAN subnetwork and the data exchanged on the higher level
network reside in the same internal memory in the Anybus Communicator CAN. In order to
exchange data with the CAN subnetwork, the higher level network simply reads and writes data
to memory locations that have been specified in Anybus Configuration Manager. The same
memory locations can then be exchanged on the CAN subnetwork.
Internal Memory
Input Data
(220 bytes)
CAN Subnetwork
Output Data
(220 bytes)
General Data
Higher Level Network
Fig. 2 Memory buffer structure
The internal memory buffer is divided into three areas based on their function:
Input Data (220 bytes) This area can be read from by the higher level network.
Output Data (220 bytes) This area can be written to by the higher level network.
General Data
(up to 1024 bytes)
This area cannot be accessed by the higher level network but can be used for
transfers between individual nodes on the subnetwork, or as a general “scratch
pad” for data.
The size of the General Data area is 1024 bytes. How much of that area that will
be used for communication depends on the configuration.
2.2.2 Memory Map
When building the CAN subnetwork configuration in Anybus Configuration Manager the areas in
the memory buffer will be mapped to the following memory locations:
CAN Network:
Fieldbus:
CAN Network:
Fieldbus:
CAN Network:
Fieldbus:
Write Only
Read Only
Read Only
Write Only
Read/Write
-
Input Data Output Data General Data
0x000 0x200
0x0DB 0x2DB
0x400
0x7FF
Fig. 3 Memory Map
The illustration shows the maximum available data areas in Anybus Communicator CAN. The actual
amount of memory that can be allocated depends on the fieldbus network used.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Description 7 (42)
2.3 PROFINET IRT Protocol
PROFINET is the open Industrial Ethernet standard for automation from PROFIBUS and PROFINET
International. The PROFINET IRT device provides PROFINET IO Isochronous Real Time
Communication.
PROFINET makes a clear distinction between fast cyclical data, IO Data, and acyclical data,
Record Data. PROFINET IO Data corresponds to what is generally referred to as I/O Data in
Anybus Communicator CAN PROFINET IRT (2.32). PROFINET Record Data is not supported.
Anybus Communicator CAN PROFINET IRT (2.32) acts as a PROFINET device (slave), which means
it can be accessed by a PROFINET controller (master), but will not initiate communication by
itself.
PROFINET IO Data (I/O Data)
PROFINET IO Data is exchanged cyclically and is built up by I/O modules. The actual I/O
configuration is determined by the PROFINET IO Controller. The modules are mapped to the
Input and Output Buffers in the order of their slot number.
The first two bytes of the I/O data area are reserved for the Control Word and the Status Word,
which are used by the IO Controller to control and report status on the nodes on the CAN
subnetwork. The remainder is available for real-time data transfer using PDOs.
GSD File
All PROFINET devices are associated with an XML-based GSD file. This file contains information
about the basic capabilities and configuration options of the device.
The latest version of the GSD file for Anybus Communicator CAN PROFINET IRT (2.32) can be
downloaded from www.anybus.com/support.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Description 8 (42)
2.4 CAN Network Protocol
2.4.1 General
The CAN protocol is message-based and can exchange up to 8 bytes of data in each message.
The protocol only acts as a data carrier, it is up to each application to define and interpret the
data content of the messages.
Data is exchanged using frames. Each frame has a unique identifier for the data it exchanges,
which also represents the message priority. Anybus Communicator CAN supports both 11-bit
(CAN 2.0A) and 29-bit (CAN 2.0B) identifiers, selected in the configuration.
CAN is essentially a produce-consume protocol, where all nodes listen to all messages. The
devices recognize what data to collect by the identifier in the CAN frame. Anybus Communicator
CAN is also able to act as a network master and issue queries that demand responses. Both
methods can be used within the same configuration.
2.4.2 Message Types
Anybus Communicator CAN features three CAN message types: Query-Response,Produce, and
Consume. These message types only specify the basic communication model, not the actual CAN
protocol. All three message types can be used in the same configuration.
Query-Response
The Anybus Communicator CAN here acts as a master on the CAN subnetwork, and
communication takes place in a query-response fashion. The gateway sends a query and expects
a response within a specified timeout.
Fig. 4 Query-Response messaging
Produce and Consume
Here there is no master-slave relationship between the Anybus Communicator CAN and the
subnetwork nodes. Any node, including the gateway, may both produce and consume messages.
Nodes do not have to respond to messages, or wait for a query in order to send one. The
consumed data can be accessed from the higher level network, and vice versa.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Description 9 (42)
Fig. 5 Produce and Consume messages
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Description 10 (42)
2.4.3 Protocol Building Blocks
The following building blocks are used in Anybus Configuration Manager to describe the
subnetwork communication.
Group Agroup does not represent any specific device on the CAN subnetwork, it is only a
means to structure the transactions that have been defined for the gateway in Anybus
Configuration Manager.
Each group can be associated with any number of transactions, however the total
number of transactions in a configuration is limited to 128.
Transaction Atransaction consists of one or more CAN frames. Each transaction is associated with a
set of parameters controlling how and when to use it on the subnetwork. There are 5
transaction types: produce,consume,query-response,dynamic produce and dynamic
consume. A group can contain transactions of all three types simultaneously.
A total of 128 transactions can be configured.
Dynamic Transaction Adynamic transaction makes it possible for a network master to change selected
parameters during runtime. The parameters are mapped to the Output or General Data
areas and cannot be changed using Anybus Configuration Manager.
A dynamic transaction can only consist of a single CAN frame which in turn can only hold
one data object.
Only one dynamic produce transaction and one dynamic consume transaction can be
configured.
CAN Frames CAN frames are low level entities used to compose transactions. Each frame carries an
11-bit or 29-bit identifier and can hold up to 8 bytes of data.
A total of 256 CAN frames can be configured.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Description 11 (42)
2.4.4 Control and Status Words
The optional Control and Status Words can be used to control the startup mode of the Anybus
Communicator CAN and to read the status of the CAN subnetwork. The Control Word is always
mapped to the first two bytes of the output data area, and the Status Word to the first two bytes
of the input data area, with the Least Significant Byte in the first byte (byte 0).
Fig. 6 Memory buffers
The illustration shows the maximum available data areas in Anybus Communicator CAN. The actual
amount of memory that can be allocated depends on the fieldbus network used.
Control Word
The Control Word can be used to reset the CAN controller and to select the startup mode and/or
reboot the Anybus Communicator CAN.
Bit Name Description
15 - 3 (reserved)
2 Reset CAN 1 - Resets the CAN controller (used when CAN interface is bus off)
1Reboot module 1 - Reboots the Anybus Communicator CAN (software reset)
0Operation mode Sets the start-up operation mode of the Anybus Communicator CAN:
0 - Idle (no new data is issued to the CAN subnetwork. Data received from the CAN
subnetwork is sent on to the higher level network.)
1 - Run (data is exchanged between CAN subnetwork and higher level network.)
Status Word
The Status Word holds information from the CAN subnetwork.
Bit Name Description
15 - 6 (reserved)
5 CAN overrun 0 - OK
1 - CAN reception overrun
4 Error passive 0 - CAN interface is NOT in error passive state
1 - CAN interface is in error passive state
3Bus off 0 - Bus runnning
1 - Bus off
2 Reset CAN
complete
If set, the CAN controller has been reset (used when CAN interface is bus off)
1(reserved)
0Operation mode 0 - Idle
1 - Run
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Description 12 (42)
2.4.5 Transaction Live List
The optional Transaction Live List consists of a bit array where each bit corresponds to a
transaction on the CAN subnetwork (bit 0 corresponds to transaction 1 etc.). A set bit indicates
normal functionality. The bit is not set if the transaction is non-working or non-existent.
The live list is mapped in the Input data area of the memory, either at the start of the area or
directly after the Status word. From 8 transactions up to 128 transactions in steps of 8 can be
monitored using the live list. This means that up to 16 bytes of the input data area of the
memory can be occupied by the live list.
The latest live list can always be accessed in Anybus Configuration Manager, regardless of
whether the live list is mapped in the input data area or not.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Installation 13 (42)
3 Installation
This product contains parts that can be damaged by electrostatic discharge (ESD). Use
ESD prevention measures to avoid damage.
3.1 Installation Overview
These are the basic steps for installing Anybus Communicator CAN gateways.
Depending on the fieldbus network type there may also be configuration switches on the Anybus
Communicator CAN that need setting. See the following sections for more information.
Basic installation steps
1. Mount the Anybus Communicator CAN on the DIN rail.
2. Connect the CAN network.
3. Connect the fieldbus network.
4. Configure the fieldbus network interface (if applicable).
5. Connect the power cable and apply power.
6. Connect the USB cable between the gateway and a PC.
7. Download Anybus Configuration Manager from www.anybus.com/support
and install it on the PC following the instructions in the installer.
(Anybus Configuration Manager requires Microsoft®Windows XP or later)
8. Continue to Configuration, p. 18
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Installation 14 (42)
3.2 Connectors and Indicators
3.2.1 External Parts
Fig. 7 Overview
1LED indicators
2DIN rail mount
3Power connector
4CAN connector
5USB connector
6PROFINET IRT network interface
3.3 DIN Rail Mounting
The unit must be electrically grounded through the DIN rail for EMC compliance.
Mount on DIN rail
Fig. 8 Push down to mount or remove
1. Hook the unit onto the upper lip of
the rail and push gently downwards.
2. Push the unit towards the rail until it
snaps into place.
Remove from DIN rail
1. Push the unit gently downwards on the rail.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Installation 15 (42)
2. Pull the bottom end of the unit free of the rail and remove it.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Installation 16 (42)
3.4 CAN Interface
The CAN network connector is located on the bottom of the unit.
Fig. 9 CAN connector
Pin Signal
2 CAN_L
3 CAN_GND
5Shield
6 CAN_GND
7 CAN_H
1, 4, 8, 9 (reserved)
3.5 PROFINET Interface
The PROFINET IRT interface contains a dual port Ethernet switch with RJ45 type connectors. The
two ports are labeled LAN 1 and LAN 2.
1 8
Fig. 10 Ethernet connector (RJ45)
Pin Function
1 TD+
2 TD-
3 RD+
6 RD-
4, 5, 7, 8 (reserved)
3.6 Power Connector
See also Technical Data, p. 39 regarding power supply requirements.
1 2
Fig. 11 Power connector
Pin Signal
1 +24 VDC
2Power Ground
3.7 USB Connector
The USB connector is used for connecting the Anybus Communicator CAN to a computer for
uploading and downloading configurations. The USB cable should be removed when not in use.
1
2
34
Fig. 12 USB type B connector
Pin Signal
1 +5 V input
2USBDM (USB communication)
3USBDP (USB communication)
4Signal ground
Housing Cable shield
69
5 1(male)
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Installation 17 (42)
3.8 LED Indicators
The LED indicators provide diagnostic information about data communication and status of the
network interfaces as well as general device status.
1 2
3
5
4
6
LED 1 to 4 PROFINET IRT network status
LED 5 CAN network status
LED 6 Device status
LED Indication Meaning
1 - Network Status Off Offline
– No power
– No connection to IO Controller
Green Online (RUN)
– Connection to IO Controller
Green, 1 flash Online (STOP)
– Connection to IO Controller
– IO Controller in STOP state or IO data bad
– RT synchronization not finished
Red Fatal error
Red, 1 flash Station name error
Red, 2 flashes IP address error
Red, 3 flashes Configuration error
Alternating red/green Firmware update in progress
2 - Module Status Off No power or initializing
Green Normal operation
Green, 1 flash Diagnostic event present
Red Fatal error
Alternating red/green Firmware update in progress
3 - Link/Activity 1
4 - Link/Activity 2
Off No power or no link detected
Green Link OK
Green, flickering Transmitting/receiving data
LED Indication Meaning
5 - CAN Subnet Status Off No power or no CAN communication
Green Running, no errors or timeout
Red. flashing Transaction error, timeout, or CAN subnet stopped
Red Fatal error
Device Status Off No power or initializing
Green Running
Green, flashing Idle
Red Fatal error
Alternating red/green Configuration error
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US

Configuration 18 (42)
4 Configuration
4.1 Configuration Overview
Device Description Files
A device description file contains a description of a network device, its functions, object
dictionary implementations, etc., and is used when configuring the network interface. The device
description file can be referred to as a DDF, EDS, GSD, etc., depending on the type of network.
The latest versions of the device description files can be downloaded from
www.anybus.com/support.
Basic steps when configuring Anybus Communicator CAN PROFINET IRT (2.32)
1. Install, connect and power up the Anybus Communicator CAN gateway (if you have not
already done so). See also Installation, p. 13.
2. Download Anybus Configuration Manager from www.anybus.com/support and install it.
3. Download the latest device description file for Anybus Communicator CAN PROFINET IRT
(2.32) from www.anybus.com/support.
4. Build your configuration using Anybus Configuration Manager and download it to the
gateway.See Anybus Configuration Manager, p. 24.
5. Install the appropriate device description file in the PROFINET IRT configuration tool.
6. Configure the PROFINET IRT network as required. Make sure that the configuration matches
the configuration present in the Anybus Communicator CAN.
Anybus®Communicator™CAN PROFINET®IRT (2.32) User Manual SCM-1202-035 1.2 en-US