Hobby King Fokker Dr.I User manual

Fokker Dr.I
F36
1.5mmx175mm Carbon Rod
F46 F15 F13
F12
F35
F37
F38
F39
1.5mmx250mm
Carbon Rod
F41
F44
F45
F17
F16
F22
F40 F22-1
F21
F43
F20
F19
F18
F5 F7
F6
F3
Ａ5
Ａ3
Ａ2
Ａ7
Ａ1
Ａ6
Ａ4
Ａ8
C5
C3
C3 C1
C2
C6
C7
C4
C8
1.5mmx155mm
Carbon Rod
C2
C1
C7
W10
W9
W7
1.5mmx347mm
Carbon Rod
W11
W43 W3
W6
W18
W36
W37
W7
W39
W40
W34
W29
W34
W29
W30
W30
W30
W29
W29
W29
W42
W41
W29
W29W30
W39-1
W21
W22
W6
W12
W13
W2
W4
W3
W1
Outer：6x50mm Carbon Tube
Inner：3x98mm
Carbon Tube
Install the aileron onto the
upper wing by paper hinges.
3. Assemble the upper wing
1.Assemble the Fuselage 2.Assemble the wing of landing gear
3.1. Assemble the Aileron
BALSA WOOD AIRPLANE
Instruction Manual
F25
F8
F10
F11 F30
F32
F8
F9
F4 F48
F35
F33
F26
F47
F23
F1
F22
F29
F34
F28
F2
F8-1

Specification
Wingspan：770mm
Length：630mm
Net weight：≈650g
Suggested Equipment
Motor： 2212 800-1000KV
ESC：20A
Servo：2.5g *2 & 5g *2
Propeller：7-8 inch
Battery：2-3S 1300-1800mAh
Radio≥3CH
W11
W14
W15
W7
W6
W35
W31
W31
W31
W31
W49
W57
W51
W52
W57
W29
W29
W29
W29
W29
W29
W29 W47
W48
W46
W44
W45
W7
W23
W20
W33
W32
W19
W29 W28
W9
W10 W7
Inner：6x37mm Carbon Tube
Outer：3x77mm Carbon Tube
1.5mmx327mm
Carbon Rod
W11
W10
W9
W8
W36
W29
W29
W29
W29
W29
W29
W29
W29
W29
W55
W31
W31
W31
W31
W31
W31
W56
W54
W25
W24
W53
W26
W7
W16
W17
W27
W7
W58
W50
W50
Inner：6x37mm Carbon Tube
Outer：3x77mm Carbon Tube
1.5mmx294mm
Carbon Rod
T7
T2
T6
T5
T4
T3
T1
T10
T14 T15 T15
T17
T20T20
T17
T16
T18T18T18 T18T19
T19
T11 T11
T12 T12
T13 T13
6.2. Assemble the wing
6.3 Install the landing gear and wing
of langing gear.
6.3.3 Assemble and install the wheel.
6.3.1 Install the landing
gear onto the fuselage. 6.3.2 Assemble the wing of
landing gear.
Insert the steel wire rod
6.4 Assemble the cowling and scale parts.
7.1 Assemble the motor and motor mounting base.
7.2 Assemble the servo
and push rod for aileron.
7.3 Assemble the elevator
rudder.
7.4 Assemble the servo horn and
push rod for elevator and rudder.
8. Adjust the C.G
6.2.1. Plug and assemble together the middle
wing,then install onto the fuselage.
Fix the horizontal tail with glue.
Glue the reinforcing bar here. Assemble the vertical tail onto
the fuselage by paper hinges.
6.2.3. Plug and assemble together the
lower wing,then install onto the fuselage.
6.2.4. Connect the upper,middle and
lower wing by aluminum rod
(as▲marked)
6.1Install the horizontal and vertical tail onto the fuselage.
5.1. Assemble the
horizontal tail
screw
screw
screw
screw
screw
▲
Insert through the preserve
slots and fix with glue.
screw
screw
screw
scale machine gun
rubber ring/
/wind shield
scale engine
cowling
carbon rod
Carbon fiber strip+screw
wheel stopper
7. Assemble the power system
B3
B2
B4
Diagram for push rod inside the fuselage
4. Assemble the middle wing
5. Assemble the lower wing
5.2. Assemble the vertical tail
6. Assemble the other components
T8
T9
6.2.2. Plug and assemble together the
upper wing,then install onto the fuselage
by aluminum rod and fix with screws.
125mm
C.G