Fisher-Price GeoTrax V7867 User manual

www.fisher-price.com
V7867
Please keep this instruction sheet for future reference,
as it contains important information.
Requires six “AAA” (LR03) alkaline batteries (not included) for operation.
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included)
Wipe with a clean, damp cloth. Do not immerse the vehicle or remote controller.
Actual product may appear different than the photos shown.

Assembled Parts
Curved Bridge TrackBridge Track
2 Bridge Rails
5 Bridge Supports Crane
Curved Ramp Track Easy Load TrackLong Guard Rail
L
G
d
R
il
5 Long Straight Tracks 5 Curved Tracks 2 Short Guardrails
Ramp Track
Short Straight Track
"Y" Support
2 "Y" Tracks
Storage Drawer 6 Table Legs
6 Leg Supports
3 Table Tops
2
Shown Actual Size
Note: Tighten or loosen all screws with a
Phillips screwdriver. Do not over-tighten.
#8 x ¾" (1,9 cm) Screw – 30

3
Slide the storage drawer into the grooves in a•
storage table.
5
Lay a table top with the bottom side up on a flat surface.•
Fit the leg assembly into the grooves in the table top.•
3
Insert two screws into each leg support and tighten.•
2
Table Assembly
Fit the leg supports into the slots in each table leg.•
Hint: The leg supports are designed to fit onto the table
legs one way. If a leg support does not seem to fit, turn it
around and try again!
1
Insert six screws into the holes in the leg assembly•
and tighten.
Repeat steps 1-4 to assemble the other two tables.•
4
CAUTION
This product contains small parts in an
unassembled state. Adult assembly is required.
Table Leg
Table Top
Storage
Drawer
Leg Supports
Table Leg

4
Fit the bridge rails to the top of the bridge assembly.•
6
Fit the bridge track onto two bridge supports, as shown.•
4Track pieces easily snap together.•
7
Fit two more bridge supports onto the bridge assembly,•
as shown.
5
Fit the long guard rail onto a curved ramp track,•
as shown.
1
Fit the “Y” support onto the bottom of the curved•
ramp track.
2
Track Setup
"Y" Support
Bridge Supports
Bridge Track
Curved Ramp
Track
Short
Guard
Rail
“• Snap” the short guardrails onto the curved tracks.
3
Curved
Track
Long Guard
Rail
Bridge Rails

5
Easy Load Track
Long Straight
Tracks
Long Straight
Track
Crane
Short
Straight
Track
"Y" Tracks
Long Straight
Track
Long Straight
Track
Curved Track
with Guard Rail
Curved Track
with Guard Rail
Ramp
Track
Bridge
Assembly
Curved Track
Curved Bridge
Track
Curved Tracks
Table Layouts
Track Layout
Slide a smooth side of a table onto any tabbed side of another
table to create the table layouts below!
Curved Ramp
Assembly

6
Battery Safety
Information
In exceptional circumstances, batteries may leak
fluids that can cause a chemical burn injury or ruin
your toy. To avoid battery leakage:
• Do not mix old and new batteries or batteries of
different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods of non-use.
Always remove exhausted batteries from the toy.
Dispose of batteries safely. Do not dispose of this
product in a fire. The batteries inside may explode
or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy
before charging.
• If removable, rechargeable batteries are used, they are
only to be charged under adult supervision.
Vehicle
• Locate the battery compartment on the back of
the vehicle.
• Loosen the screws in the battery compartment door
with a Phillips screwdriver. Lift the battery compartment
door and insert three “AAA” (LR03) alkaline batteries.
• Close the battery compartment door and tighten the
screws with a Phillips screwdriver. Do not over-tighten.
• If the vehicle begins to operate erratically, you may
need to reset the electronics. Remove the batteries and
replace them in the vehicle.
Remote Controller
Locate the battery compartment on the bottom of the•
remote controller.
Loosen the screw in the battery compartment door with•
a Phillips screwdriver. Remove the battery compartment
door and insert three “AAA” (LR03) alkaline batteries.
Replace the battery compartment door and tighten the•
screw with a Phillips screwdriver. Do not over-tighten.
If the remote controller begins to operate erratically,•
you may need to reset the electronics. Remove the
batteries and replace them in the remote controller.
ICES-003
This Class B digital apparatus complies with•
Canadian ICES-003.
Operation is subject to the following two conditions: (1) this•
device may not cause harmful interference and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme à la•
norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée seulement•
aux conditions suivantes : (1) il ne doit pas produire de
brouillage et (2) l’utilisateur du dispositif doit être prêt
à accepter tout brouillage radioélectrique reçu, même
si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
Battery Installation
• Protect the environment by not disposing of
this product with household waste (2002/96/
EC). Check your local authority for recycling
advice and facilities (Europe only).
1,5V x 6
“AAA” (LR03)
We recommend the use of alkaline batteries for longer battery life.
IMPORTANT! Under normal use conditions, the batteries
in the vehicle will require replacement more often than
the batteries in the remote controller. For additional
information, refer to the troubleshooting section.
Vehicle

7
POWER BUTTON
READY LIGHT
• Press the power button on top of the vehicle. The ready
light turns on.
1
All Aboard!
Hint: We do not recommend using the vehicle on carpets.
For best performance, use on hard, flat surfaces.
2
3
1
• Point the antenna of the remote controller toward the
vehicle and push the stick forward. The vehicle
moves forward.
• Pull the stick all the way back and the vehicle travels in
reverse. Release the stick to stop.
1
2
3
FORWARD
STOP
REVERSE
2
Troubleshooting
PROBLEM SOLUTION
Vehicle drives slowly Battery power in the vehicle may be
weak. Replace all three batteries in the
vehicle with new, alkaline batteries.
The wheels on the vehicle may be dirty.
Wipe them with a clean cloth.
Vehicle does not
respond to the
remote controller
Battery power in the remote controller
may be weak. Replace all three
batteries in the remote controller with
new, alkaline batteries.
You may be beyond the maximum
range of the remote controller which is
about 12 feet (3,6 m).
You may not have a clear path
between the remote controller and
the vehicle. This toy works best when
there are no obstructions between the
vehicle and the remote controller.
Bright sunlight or fluorescent lights
may affect the range of the remote
controller. Try dimming the room you
are playing in.
The vehicle may have shut off. If you
do not operate the remote controller
for a few minutes, the vehicle shuts
off automatically and the ready light
turns off. Press the power button on
the vehicle, and operate the remote
controller to restart.

PRINTED IN MEXICO V7867pr-0920
CO
N
SU
MER
ASS
I
S
T
A
N
C
E
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2011 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Consumer Information
FCC Statement (United States Only)
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Consult the dealer or an experienced radio/TV
technician for help.
Note: Changes or modifications not expressly approved
by the manufacturer responsible for compliance could
void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause
undesired operation.