Hobby King Li13der-EP User manual

Specs:
Wing Span: 1016mm
Wing Area: 27.3 Sq dm
Length: 923.5mm
Weight: 650g RTF
Required:
Motor: BL2214 - 1000kv
Radio: 4 hannels,
Servos: 4 x 9g servo
Battery: 3S 1300~1500mAh
ESC: 20~25A
Warning!
This item is not a toy. It has the potential to ause serious harm if mistreated. The user a epts all
responsibility in the assembly of this model. Always he k the model to ensure it is free of damage and all
s rews and ontrol hardware is tight before ea h flight.

Wing Assembly
1) Aileron ontrol hardware – ontrol horns, levis, pushrod onne tor, pushrod, ontrol horn s rews.
2) Cut overing to expose servo mounting holes. Servos are mounted on the bottom of the wing.
3) Cut overing away at rudder servo lo ation on top of wing. Servo is mounted in the fuselage, but
needs learan e from the wing. Cut Hole in enter of wing sheeting for aileron servo leads.

4) Cut overing to insert main wing. Use a overing iron to seal edges of overing.
5) Glue wing with CA glue or epoxy, use a hobby knife to pun ture overing for better glue penetration.
6) Glue hinges with thin CA glue.

7) Install aileron servo, se ure with s rews.
8) Install aileron ontrol horn, se ure with s rews. Control horn in ludes square ba kplate for top of aileron.
9) Thread levis to ontrol rod. Pushrod onne tor should be installed on outermost hole in servo arm for
best ontrol throw. Center aileron with servo arm at 90 degrees to ontrol rod. Se ure pushrod with set
s rew. A small amount of thread lo k should be applied to set s rew to prevent it oming loose over time.

Tail Assembly
1) Tail hardware – Pull Pull ables, levis, aluminum rimps, ontrol horns, elevator joiner, tail wheel
2) Cut overing to install stabilizer. Seal edges with overing iron.
3) Cut overing for elevator servo mount on right side only.

4) Insert elevator into fuselage before installing stabilizer fin
5) Insert stabilizer into slot, enter it, pun ture overing at lo ation it onta ts fuselage, then glue in pla e
with CA or Epoxy.
6) Glue hinge with thin CA.

7) Install elevator servo, se ure with s rews. You may need a small servo extension lead for the elevator
servo to rea h your re eiver.
8) Install elevator horn, se ure with s rews and in luded ba kplate.
9) Glue verti al fin with CA glue or epoxy

10) Glue plywood tail wheel mount with CA glue or epoxy.
11) Cut a small hannel in balsa wood for tail wheel wire.
12) Drill a diameter 1.5mm hole to install the tail wheel wire.

13) Glue hinge with CA glue.
14) Glue tail wheel steel wire with CA glue or epoxy. A small pie e of lear tape wrapped around works for
double se urity.
15) Install rudder servo, se ure with s rews.

16) Insert rudder pull pull ables down the length of the fuselage to the rudder servo arm. Insert ables
through threaded fittings, loop able through, use aluminum rimps to se ure able.
17) Install rudder horn, se ure with s rews and nut M2 nuts.
18) Center servo arm, and rudder. Pull ables tight and loop able through threaded ends, se uring with
aluminum rimps. Final tension an be adjusted through the levis to threaded end.

Landing Gear Assembly
1) Main Landing Gear parts.
2) Glue plywood with CA or a Rubberized CA glue.
3) Cut slot in wheel pant to onform with plywood insert

4) Se ure wheels to landing gear with wheel ollars set s rews.
5) Insert wheel into wheel owling. Hold in pla e with wheel ollars and sets rew.
6) Install main landing wheel

7) Install wheel pants, se ure with s rews
Canopy/ Final Assembly
1) Canopy Parts
2) Glue short fiberglass anopy pins with CA glue.

3) Cut overing away to install motor