Holman weatherWHIZ WS5061 User manual

1 of 8
User Guide
2019
Model no WS5061

2 of 8
Introduction
Thank you for purchasing our
WeatherWhiz™ Wireless Weather Reader.
Please read the operating instructions carefully to
familiarise yourself with the features and modes
of operation before using the instrument.
Tech Specs
LSix keys: MODE / +/ −/ ALARM /
CHANNEL / SNOOZE / LIGHT
LTime display: 12/24 format
LCalendar: Continuous up to 2099, day, date, month
LAlarm: Dual function with 5 minute snooze
LForecasting: Sunny, partly sunny,
cloudy, rainy, stormy
LBarometer: hPa, inHg
LTemperature: °C, °F, indoor and outdoor with trend
LTemperature range: Inside: 0~50°C,
Outside: -20~60°C
LBattery indication: Low indication
LBatteries (not included): Indoor: 3× AA, LR06,
1.5V / Outdoor 2× AAA, LR03, 1.5V
LBacklight: Blue LED
LSensor frequency: 433MHz with 3× channels
LTransmission range: 50m without
interference, at least 1m above ground
Contents
Introduction 2
Tech Specs 2
Overview 3
Operation 4
Before You Begin 4
Mounting the Outdoor Sensor 4
Manual Time Setup 4
Daily Alarm Setup 4
Daily Alarm On/Off 5
Snooze Function 5
12/24 hours mode 5
°C/°F temperature display 5
Max/Min for Indoor/Outdoor Temperature 5
Weather Forecast 5
Illumination 5
Altitude and Weather Icon Selection 5
Low Battery Condition Display 5
Operation 5
RF Wireless Connection to the Outdoor Sensor 6
Operation 6
Warranty 7
2 Year Replacement Guarantee 7

3 of 8
1. Air pressure trend
2. Freeze
3. Weather
4. Trend of indoor temperature
5. Max/min of indoor temperature
6. Indoor
7. Indoor temperature
8. Low battery of indoor station
9. Cycle symbol for channel
10. Date
11. Month
12. Time
13. Snooze
14. Air pressure reading
15. Outdoor channel
16. RF symbol
17. Max/min for outdoor
temperature
18. Trend of outdoor temperature
19. Outdoor temperature
20. Low battery of outdoor sensor
21. Week
22. Day of week
23. Alarm 1
24. Alarm 2
A. SNOOZE/LIGHT
B. MODE
C. ALARM
D. +
E. –
F. CHANNEL
G. Battery compartment
Insert the batteries in the
transmitter before beginning
Obstructions can substantially
constrain the coverage
of the transmitter
Protect the transmitter from
direct sunlight and rain
Overview

4 of 8
Operation
Before You Begin
1. Open the battery compartment located
at the rear side of each device
2. Place the batteries in the battery
compartment as per the polarity shown
3. ALTITUDE will flash. Use + / −to
set the altitude of your position
4. Press SNOOZE/LIGHT
5. The weather symbol will flash. Use
+ / −to choose the weather
6. Press SNOOZE/LIGHT
7. hPa and inHg will flash. Use + / −to select
8. The Indoor Display Console is now
connecting to the Outdoor Sensor. This
process takes about 3 minutes. The display
will then show the outdoor temperature
9. In case of reception failure, press CHANNEL
for more than 3 seconds to receive again
Mounting the Outdoor Sensor
We suggest the outdoor sensor to be hung as shown
Do not place outside, and try to avoid direct
sunshine or rain as much as possible
Manual Time Setup
1. Press and hold MODE for 3 sec
2. 12/24hr format will flash; use + / −to select,
press MODE to confirm
3. HOUR will flash; use + / −to select,
press MODE to confirm
4. MINUTES will flash; use + / −to select,
press MODE to confirm
5. YEAR wil flash; use + / −to select,
press MODE to confirm
6. MONTH will flash; use + / −to select,
press MODE to confirm
7. DATE will flash; use + / −to select,
press MODE to confirm
The clock automatically changes from setup mode
to time display if no keys are pressed for 20 sec
Daily Alarm Setup
1. Press ALARM to switch from
time display to A1 display
2. Press and hold ALARM for 3 sec, the
flashing alarm times will show
3. The HOUR display of the alarm time will flash;
use + / −to select, press ALARM to confirm
4. The MINUTE display of the alarm time will flash;
use + / −to select, press ALARM to confirm
5. Press ALARM again to switch from
A1 display to A2 display
6. Repeat the above steps to set the time for A2

5 of 8
Daily Alarm On/Off
1. When showing A1 alarm time, use + or −
to activate A1 with alarm symbol showing
2. Press + or −again cancel the alarm
3. When showing A2 alarm time, use + or −
to activate A2 with alarm symbol showing
4. Press + or −again cancel the alarm
A1 operates from Monday to Friday
A2 operates from Saturday to Sunday
The clock automatically changes from setup mode
to time display if no keys are pressed for 20 sec
Alarms sound for 2 minutes
if no key is pressed to stop it
Snooze Function
1. Press the SNOOZE/LIGHT while the alarm
sounds to activate the snooze function
2. If the snooze function is activated,
SNOOZE symbol will flashing
3. The alarm repeat after 5 min
4. The snooze function can be stopped by pressing
any key
12/24 hours mode
Time can be shown in 12hr (AM/PM) or 24hr mode
°C/°F temperature display
Temperature can be shown in °C or °F; press
the key −to switch between modes
Max/Min for Indoor/Outdoor Temperature
Press + to display indoor/outdoor
max/min of temperature
Weather Forecast
As the weather is forecast by the
barometer, the display may have
discrepancies with the actual weather
Hold SNOOZE/LIGHT button for 3 sec; weather
icons will flash, use + or −to select the icons
Illumination
Press SNOOZE/LIGHT to
illuminate the display for 5 sec
Altitude and Weather Icon Selection
1. Hold SNOOZE/LIGHT for 3 sec;
altitude will flash which
2. Press SNOOZE/LIGHT the weather icon will
flash, use + or −to select weather icon
3. Press SNOOZE/LIGHT, the hPa will flash, use
+ or −to switch between hPa and inHg
If altitude is left unadjusted, the barometer
reading is set to comparative air pressure
If altitude is set to 0, the barometer
reading will be local air pressure
Low Battery Condition Display
Low battery indicators for both the
Indoor Display Console and Outdoor Sensor,
are shown in their respective areas on the
Indoor Display Console
Operation
SUNNY PARTLY
CLOUDY CLOUDY RAIN HEAVY RAIN

6 of 8
RF Wireless Connection to the Outdoor Sensor
1. Press CHANNEL to choose an RF channel
to read data from up to 3 Outdoor Sensors
on one Indoor Display Console
2. Press and hold CHANNEL for 3 sec to
search for an Outdoor Sensor
When placing both the Indoor Display Console
and Outdoor Sensor, remember they
are subject to interference
Install both units as close as possible to each other
Try to avoid outside interference by not placing
them near computers, TVs, aerials etc.
Concrete walls and floors can
interrupt transmissions; try to avoid
these as much as possible
If the connection is successful initially but fails
occasionally, try to reduce the distance
Operation

7 of 8
Warranty
2 Year Replacement Guarantee
Holman offers a 2 year replacement guarantee with this product.
In Australia our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
As well as your statutory rights referred to above and any other rights and remedies you have under
any other laws relating to your Holman product, we also provide you with a Holman guarantee.
Holman guarantees this product against defects caused by faulty workmanship and materials for
2 years domestic use from the date of purchase. During this guarantee period Holman will replace
any defective product. Packaging and instructions may not be replaced unless faulty.
In the event of a product being replaced during the guarantee period, the guarantee on the replacement product
will expire 2 years from the purchase date of the original product, not 2 years from the date of replacement.
To the extent permitted by law, this Holman Replacement Guarantee excludes liability for consequential
loss or any other loss or damage caused to property of persons arising from any cause whatsoever. It also
excludes defects caused by the product not being used in accordance with instructions, accidental damage,
misuse, or being tampered with by unauthorised persons, excludes normal wear and tear and does not cover
the cost of claiming under the warranty or transporting the goods to and from the place of purchase.
Should you suspect your product may be defective and need some clarification or advice please contact us directly:
1300 716 188
[e-mail]
11 Walters Drive, Osborne Park 6017 WA
If you are certain your product is defective and is covered by the terms of this warranty, you will
need to present your defective product and your purchase receipt as proof of purchase to the place
you purchased it from, where the retailer will replace the product for you on our behalf.

8 of 8
Copyright © 2019 Holman Industries
Head Office/Service
11 Walters Drive, Osborne Park WA 6017
Ph: [phone] Fax: [phone]
[email protected]
www.holmanindustries.com.au
We really appreciate having you as a customer, and would like to say thank you for choosing us.
Should you have any questions about this product or its operation please call customer service on 1300 716 188.
Thanks for being a
#SMARTGARDENER
We hope you are happy with our product and if you have a moment to leave a
review, we would like to hear your feedback on the Product Review website.
www.productreview.com.au then search for our product name