Holmatro SMC 4006 Technical specifications

SMC 4006 / 4006 C 01D19
Repair & Maintenance
instructions Rescue equipment
Maintenance recommendations after use (every time)
Wear full protective gear during maintenance !
Always act according to the safety instructions as supplied with each tool !
Contact the Holmatro dealer if one of the items does not work properly !
•Necessary equipment: see check list page 12.
Left: SMC 4006 Right: SMC 4006 C
Step 1
•Check the cutter for completeness, oil leaks
and damage. Do not use the cutter if it leaks
or is damaged, and contact the Holmatro
dealer.
•Check general condition of the cutter.
Clean/dry the tool with soft cloth.
•Check the attachment of the carrying handle.
If necessary, fasten it firmly by tightening the
wing screw.
Step 2
•Check coupler(s) and dust cap(s) for damage,
dirt and/or oil leakage.
•Clean coupler(s) with a clean and soft cloth, if
necessary with water and soap.
•If necessary grease with hydraulic oil or use
WD-40.
•Check functioning coupler(s) (see page 13).
•Reconnect loose dust cap(s) to coupler(s).
Step 3
•Check the functioning of the control handle, it
must automatically return to it’s neutral
position.
•Contact the Holmatro dealer if the handle
does not work properly.
Step 4 (only for pigtail connection)
•Check the back of the control handle for oil,
this will indicate that the safety valve has been
activated during use (return line of the tool
was not connected properly to the returnline of
the pump).
•Clean the deadman’s handle internally by
blowing compressed air in the back of the
handle.
•Check the hose for damage.
© Holmatro 09/08
While the greatest care has been devoted to the content, it is
possible that the information in this printed matter is incorrect
or incomplete. Holmatro N.V. and its affiliated companies
(hereafter: Holmatro) cannot be held liable in any way for the
consequences of activities undertaken on the
basis of this
printed matter. If you have any doubts about the correctness
or completeness of the information, you shall contact
Holmatro (phone number: [phone]).
Nothing from this printed matter can be copied and/or made
public in any way witho
ut the explicit authorisation of
Holmatro.
Manufacturing sales & service Manufacturing sales & service
worldwide U.S.A., Canada and Latin America
Holmatro Rescue Equipment B.V. Holmatro, Inc.
P.O. Box 33, 4940 AA Raamsdonksveer 505 McCormick Drive, Glen Burnie, MD
The Netherlands 21061 U.S.A
T+ 31 (0)162 - 58 92 00 T+ 1 - 410 - 768 - 9662
F+ 31 (0)162 - 52 24 82 F+ 1 - 410 - 768 - 4878
E[email protected] [e-mail]
www.holmatro.com www.holmatro-usa.com
Pigtail
connection
only !
1 - 3

SMC 4006 / 4006 C 01D19
Repair & Maintenance
instructions Rescue equipment
Maintenance recommendations after use, continued
Step 5
•Check the presence of the lock-nut.
•Check if the upper moving part can move
freely. If not see page 8 step 9 to adjust.
Step 6
•Clean the blades after use.
•Check the blades for damage, remove
upsettings on the blades. Use a file and
abrasive paper.
•Blades can be turned one time 120°.
•Replace, or turn blades 120° when blades are
damaged.
•See page 7 “replacing the blades” to replace
the blades.
•Lubricate the blades after use with
preservative oil WD-40.
Step 7
•Check the presence of both locking screws.
•Both lock bolts should be tightened firmly.
Step 8
•The best cutting results are obtained if the
blades (jaw opening) are open 0.5 mm to 1
mm at the end of the cutting movement.
•See page 9 “Adjusting the plunger stroke” to
adjust the plunger stroke.
Step 9
•Spray Teflon lubricating oil on and between
the moving parts of the centre bolt B while the
tool is opening and closing (cover not shown).
Step 10
•Clean/dry the tool with soft cloth before
storing it.
•Lightly oil steel parts with preservative oil
WD-40.
•Store the cutter in a dry and well-ventilated
area.
•Do not fully close the cutter, always keep a
few mm for opening, so that the tool can be
stored without pressure.
0.5-1.0mm
2 - 3

SMC 4006 / 4006 C 01D19
Repair & Maintenance
instructions Rescue equipment
Monthly maintenance recommendations (or after 10 hours of use)
Wear full protective gear during maintenance !
Always act according to the safety instructions as supplied with each tool !
Contact the Holmatro dealer if one of the items does not work properly !
•Necessary equipment: see check list page 12.
Left: SMC 4006 Right: SMC 4006 C
Step 1
•Check the operation of the tool by opening
and closing the cutter 2 times.
•No cracking sounds can be heard.
•Check the tool for damage and leaking. If the
tool doesn’t work properly and/or leaks,
contact the Holmatro dealer.
Step 2
•Check coupler(s) and dust cap(s) for damage,
dirt and/or oil leakage.
•Clean coupler(s) with a clean and soft cloth, if
necessary with water and soap.
•If necessary grease with hydraulic oil or use
WD-40.
•Check functioning coupler(s) (see page 13).
•Reconnect loose dust cap(s) to coupler(s).
Step 3
•Check whether the deadman’s handle returns
to it’s neutral position.
•Check the operation of the deadman’s handle.
Have the Holmatro dealer repair the
deadman’s handle if it doesn’t function
properly.
Step 4 (only for tools with pigtail hoses)
•Check pigtail hose(s) and mounting of the
couplers.
•Replace the pigtail hose when:
odamages are visible
othe steel inner layer is visible
oblisters are visible
oobvious traces of kinks are visible
ocuts are visible
oprotection spring is not mounted well
Step 5
•Check the presence of the lock-nut.
Check if the upper moving part can move
freely.
•If not, see page 8 step 9.
Step 6
•Check the carrying handle for damage.
Replace a damaged carrying handle.
•Check the attachment of the carrying handle.
If necessary, fasten it firmly by tightening the
wing screw.
3 - 3