holzkraft HB 1401 User manual

Assembly instructions
WORKBENCH
Workbench
HB 1401
HB 1901

Assembly Instructions HB 1401/ HB 1901
Version 2.02 Edition 17.09.2019
2
1. Technical Data
Unit
HB 1401
HB 1901
Dimensions [LxBxH] approx.
mm
1340x650x850
1800x760x850
Weight approx.
kg
47
62
Length of workspace without vice jaws
mm
1340
1840
Width/depth of workspace without vice jaws
mm
500
500
Working height
mm
850
850
Board thickness
mm
30
30
Front jaw length
mm
350
360
Front jaw width
mm
55
55
Front jaw span width
mm
130
130
Front jaw span width up to centre of round hook
mm
160
160
Rear jaw length
mm
360
360
Rear jaw width
mm
55
55
Rear jaw span width
mm
130
130
Rear jaw span width up to centre of round hook
mm
160
160
Max. load
mm
350
350
2. Workbench Assembly
Pos.
Parts list
Qty.
Pos.
Parts list
Qty.
1
Bench Top
1
11
M12 x 100 Hex Bolt
4
2
Front foot with Bench Dog
Storage Holes
2
12
M12 Nut
4
3
Back Foot
2
13
Washer
4
4
Top Rail Support
2
14
6 x 40mm Hex Head Bolt
4
5
Base
2
15
5 x 50mm Wood Screw
4
6
Middle Stretchers
2
16
6 x 30mm Hex Head Bolt
8
7
Center shelf
1
17
Handle ends
4
8
Vise Face
2
18
Dowels
28
9
Vise Assembly
2
19
Bench Dog
4
10
Vise Handle
2
20
Glue (not shown)
1

Assembly Instructions HB 1401/ HB 1901
Version 2.02 Edition 17.09.2019
3
2.1 Illustrations
Illustration 1 Illustration 2
Illustration 3 Illustration 4
Illustration 5

Assembly Instructions HB 1401/ HB 1901
Version 2.02 Edition 17.09.2019
4
2.2 Assembly Instructions
1. Place Base (5), Top Rail Support (4), Back Leg (3) and Front Leg with Bench Dog Storage
Holes (2) with dowel holes facing inward als shown (Ill. 1). Attach the Base and Top Rail
Support to the Front Leg with Bench Dog Holes (2) and Back Leg (3) using four Dowels
(18) and Glue (20) for each (see Ill.1). Use the inner holes. The outer hole on each side of
the Top Rail Support (4) will later be used to attach the Bench Top (1). Repeat this process
for the other leg assembly.
2. Slide the Center Shelf (7) intro the grooves of both Middle Stretchers (6) as shown in Ill. 2.
3. Use two Dowels (18), an M-12 x 100 Hex Bolt (11), a Washer (13) and an M-12 Nut (12) to
attach each Middle Stretcher (6) to the leg assembly ((Ill. 3). The Middle Stretcher
assembly can be mounted with the Center Shelf (7) on the top (as in Ill.3) or bottom (as in
Ill. 3, little Illustration). Make sure the Bench Dog Holes in the Legs are all facing forward.
Repeat this process for the other leg assembly.
4. Slide the Vise Assembly (9) through holes in the Vise Face (8) and Bench Top (1). SSecure
Vise Assembly (9) to the Bench Top (1) with four Hex Head 6 x 30 mm Bolts (16) and to the
Vise Face (8) with two Hex Head 6 x 40mm Bolts (14. Feed the Vise Handle (10) through
the Vise Assembly (9) and attach Handle Ends (17) with Dowels (18) (Ill. 4). Repeat this
process to attach the other Vise Assembly to the front of the Bench Top.
5. Place the Bench Top (1) so it rests in place on the two leg assemblies. Attach to the Top
Rail Supports (4) with four 5 x 50 mm Wood Screw (15) one in each corner (Ill.5).
Notice
Workbench is made from high quality beech wood guaranteeing maximum resistance and
long service life of the bench.
Please observe the following points:
1. The bench must not be left in damp or humid conditions which will cause movement in
the wood. Recommended humidity level max. 60%.
2. If you bought workbench without surface treatment, we recommend you to finish the
bench by colourless varnish or oil including the bottom of workbench. Varnish (oil)
prevents absorption of surrounding moisture. Please repeat surface treatment each 6
months.
3. To increase the stability of your workbench we recommend you to bolt the bench to the
floor.Please tighten all screws every 6 months.