Home Styles 5182-26 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level
518 262-
Upholstered Bench
IMPORTANT
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
1 Left Hinge
1 Right Hinge
2 pcs.
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
M3x12
Wood Screw (short)
8 pcs. (+1 extra)
Machine Screw
4 pcs.
M3x19
Wood Screw (long)
8 pcs. (+1 extra)
Handle
2 pcs.
M3x15
Wood Screw
4 pcs. (+1 extra)
M6x50
Head Cap Bolt
8 pcs. (+1 extra)
Magnet
2 pcs.
Flat Washer
8 pcs. (+1 extra)
Spring Washer
8 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
A.
Cushion
1 pc.
B.
Top
1 pc.
F.
Base
1 pc.
G.
Back Panel
1 pc.
H.
Foot
4 pcs.
I.
Foot
1 pc.
J.
Door
1 pc.
C.
Side Panel
1 pc.
D.
Side Panel
1 pc.
E.
Middle Panel
1 pc.
K.
Door
1 pc.

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
C
D
G
Lock
STEP 1
Attach Side Panels (C) and (D) to Back Panel (G), then flip Locks.
(See Figures 1 and 2)
E
F
STEP 2
Attach unit and Middle Panel (E) to Base (F), then flip Locks.
Lock
Figure 1 Figure 2

Assembly Instructions 3/5
STEP 3
Place unit upside down on a soft cloth.
Attach Feet (H) to unit with Flat Washers,
Spring Washers and Head Cap Bolts.
(See Figure 3)
Attach Foot (I) to unit.
(See Figure 4)
Figure 5
Figure 3 Figure 4
STEP 4
Place Top (B) upside down on a soft cloth.
Attach Magnets to Top (B) with Wood Screws into pre-drilled holes. (See Figure 5)
Head Cap Bolt
Spring Washer
Flat Washer
Wood Screw
Magnet
I
H
H
H
H
B

Assembly Instructions 4/5
B
Lock
Machine Screw
Handle
Figure 6 Figure 7
STEP 5
Turn unit from Step 3 over to its upright position.
Attach Top (B) to unit, then flip Locks.
Attach Doors (J) and (K) to unit by inserting door hinges into slots
in unit and attach with Wood Screws (long). (See Figure 6)
Attach Handles to Doors (J) and (K) with Machine Screws.
(See Figure 7)
Wood Screw (long)
J
K

STEP 6
Attach Left Hinge and Right Hinge to unit with Wood Screws (short) into pre-drilled holes.
(See Figures 8 and 9)
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 10)
Place Cushion (A) into position.
Left Hinge
Wood Screw (short)
Right Hinge
Assembly Instructions /55
A
Figure 10Figure 8 Figure 9

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460