Home Styles 88 9001 007C User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
88 9001 007C
Cuisine Cart
(Please refer to the last page of these
instruction for drawer assembly steps)
Tools required for assembly : Phillips screwdriver
Hex Wrench
1 Pc.
M6x30
Head Cap Bolt(Middle)
for Top
4 Pcs. (+1 extra)
M6x35
Head Cap Bolt(long)
12 Pcs. (+1 extra)
M6x25
Head Cap Bolt
for Side Tower Bar
2 Pcs. (+1 extra)
Wood Plug
8 Pcs. (+1 extra)
Adjustable Pin
4 Pcs. (+1 extra)
M4x16
Wood Screw
for Caster
16 Pcs. (+1 extra)
Small Hex Wrench
1 Pc.
Caster
two lock
two non-lock
4 Pcs.
C.
Base
1 Pc.
A.
Side Panel
1 Pc.
H.
Side Rack
1 Pc. I.
Side Rack
1 Pc.
K.
Base Rack
1 Pc.
P.
Drawer
1 Pc.
N.
Door
1 Pc.
O.
Door
1 Pc.
M.
Shelf
1 Pc.
L.
Side Tower Bar
1 Pc.
B.
Side Panel
1 Pc.
F.
Back Stretcher
1 Pc.
G.
Front Rail
1 Pc.
D.
Back Upright
1 Pc.
E.
Back Panel
2 Pcs.
J.
Brush Chrome Pipes
3 Pcs.
Knob
2 Pcs.
M4x20
Machine Screw
for Knob
2 Pcs.

Assembly Instructions 2
Figure 1
Figure 2
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
STEP 1
Attach Casters to Base (C) with
Wood Screws for Caster.
(See fi gure 1)
STEP 2
Attach Side Panel (A) to Base (C) with Head Cap Bolts.
Attach Back Upright (D) to Base (C).
Slide Back Panels (E) into place.
Attach Back Stretcher (F) and Front Rail (G) to Side Panel (A) with Head Cap Bolts.
Attach Side Panel (B) to the unit with Head Cap Bolts.
Tighten all Bolts with Hex Wrench. (See fi gure 2)
/5
C
C
A
B
F
G
D
E
E
Locking Caster
Non-Locking Caster
Wood Screw for Caster
Head Cap Bolt
Locking Caster

Assembly Instructions 3
STEP 3
Attach Side Rack (H) to Side Panel (A)
with Head Cap Bolts.
Attach Brush Chrome Pipes (J) and Base
Rack (K) to Side Rack (H).
Attach Side Rack (I) to Side Panel (A)
with Head Cap Bolts.
STEP 4
Attach Side Tower Bar (L) to Side Panel (B)
with Head Cap Bolts for Side Tower Bar.
J
L
K
H
I
Head Cap Bolt
Head Cap Bolt
for Side Tower Bar
/5
A
B

Assembly Instructions 4
Figure 3 Figure 4 Figure 5
STEP 5
Now, you’ll be able to create your own
kitchen cart. Make your own choice the ‘Top’,
wood or stainless steel or granite.
Place the Top onto the unit with
Head Cap Bolts for Top.
Insert Adjustable Pins into the Side Panels
at the desired level.
Place Shelf (M) into position.
STEP 6
Attach Knobs to Door (N) and (O)
with Machine Screws.
(See fi gure 3)
Attach Door (N) and (O) to Side
Panel (A) and (B) by sliding the door
lift hinges into the side panel lift
hinges
(See fi gure 4)
Slide Drawer (P) into position.
Cover up all holes with Wood Plugs.
(See fi gure 5)
Adjustable Pin
Head Cap Bolt
for Top
M
N
O
P
A
B
/5

Assembly Instructions 5
Part List Hardware List
Drawer (P)
P1.
Front Part
1Pc. P3.
Side Part
1 Pc.
P4.
Side Part
1 Pc.
P2.
Back Part
1 Pc. P5.
Base Part
1 Pc.
P1
P1
P1
P3
P3
P3
P4
P4
P4
P2
P2
P5
P5
STEP 1
Attach P1, P2 and P3 using a Phillips Screwdriver
and long Wood Screws (4X), tighten halfway.
Attach P1, P2 and P4 using long Wood Screws
(4X), tighten halfway.
(See fi gure 1)
STEP 2
Slide P5 into grooves in P3 and P4.
Be sure to push P5 all the way forward so it
meets P1
(See fi gure 2)
STEP 3
Insert short Wood Screws (6X) into the pre-drilled
holes in P5, tighten screws.
(See fi gure 3)
STEP 4
Attach Pull Handle with Machine Screws.
(See fi gure 4)
Figure 1
Figure 2
Figure 3
Figure 4
MAKE SURE ROLLER
IS ON THE BACK
Tighten all screws used in drawer assembly.
/5
M3.5x13
Wood Screw(short)
for Base Drawer
6 Pcs. (+1 extra)
M3.5x25
Wood Screw(long)
for Side Drawer
8 Pcs. (+1 extra)
Pull Handle
1 Pc.
M4x20
Machine Screw
for Pull Handle
2 Pcs.