Home Styles 6800-202 User manual

Part List
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
6800-202
Sofa Table
B.
Side
2 pcs.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
For assembly see instructions in carton 6800-201.

Part List
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
6800-201
Sofa Table
A.
Top
1 pc.
C.
Base
1 pc.
F.
Container
3 pcs.
D.
Top
3 pcs.
E.
Foot
4 pcs.
Small
Hex Wrench
1 pc.
Hex Wrench
1 pc.
Spring Washer
16 pcs. (+1 extra)
M6x35
Head Cap Bolt
16 pcs. (+1 extra)
Flat Washer
16 pcs. (+1 extra)
Plug
3 pcs.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Tool(s) required for assembly: Level
Hardware List
needed for assembly.Carton 6800-202 is also

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Figure 1
STEP 1
Attach Top (A) and Base (C) to Side (B) with Head Cap Bolts, Spring Washers and Flat Washers,
tightening bolts only halfway.
(See Figure 1)
Head Cap Bolt
Spring Washer
Flat Washer
A
B
C

STEP 2
Attach Side (B) to unit with Head Cap Bolts, Spring Washers and Flat Washers,
tightening bolts only halfway.
Tighten all bolts used in Steps 1 and 2.
Flat Washer
Spring Washer
Head Cap Bolt
Assembly Instructions /36
B

Assembly Instructions /46
STEP 3
Turn unit upside down.
Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
(See Figure 2)
Figure 2
Head Cap Bolt
Spring Washer
Flat Washer
E
E
E
E

Assembly Instructions /56
STEP 4
Turn over unit to its upright position.
Place Containers (F) into position.
Place Plugs into position.
gPlu
F
F
F

Assembly Instructions /66
STEP 5
Place Tops (D) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 3)
Figure 3
DDD

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460