Home Styles 20 05520 0932 User manual

Part List
Hardware List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/16” Drill Bit, 3/8” Drill Bit
Cartons 20 05520 0931 and 0933 are also needed for assembly.
20 05520 0932
IMPORTANT
Storage Island
Cam Lock Screw
45 pcs. (+2 extra)
M4x16
Machine Screw
16 pcs.
M3 x.5 32
Wood Screw
4 pcs. (+1 extra)
Small Hex Wrench
1 pc.
Cam Lock
45 pcs. (+6 extra)
Handle
8 pcs.
Adjustable Pin
24 pcs. (+1 extra)
Flat Washer
14 pcs. (+1 extra)
Spring Washer
14 pcs. (+1 extra)
M6x32
Head Cap Bolt
14 pcs. (+1 extra)
Hex Wrench
1 pc.
H.
Side Panel
1 pc.
G.
Side Panel
1 pc.
F.
Middle Panel
1 pc.
D.
Back Panel
1 pc.
E.
Back Panel
1 pc.

Assembly Instructions 2/9
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Top (A), Middle Panel (F),
Plinths (I), Bottom (J), Side Panels (G) and (H), then tighten. (See Figure 1)
H
Cam Lock Screw
Cam Lock Screw
A
I
G
F
Cam Lock Screw
Cam Lock Screw
Figure 1
Cam Lock Screw
I
J
Cam Lock Screw

Assembly Instructions 3/9
STEP 3
Attach Bottom (J) to unit with
Flat Washers, Spring Washers,
Head Cap Bolts and Cam Locks,
tightening bolts only halfway.
(See Figure 3)
E
Flat Washer
Cam Lock
Head Cap Bolt
Spring Washer
Cam Lock
Figure 3
STEP 2
Attach Back Panels (D) and (E) to
Middle Panel (F) with Cam Locks.
(See Figure 2)
F
J
D
Figure 2

Assembly Instructions 4/9
STEP 4
Attach Plinths (I) to
unit with Cam Locks.
STEP 5
Attach Rails (C) to Side Panel (H)
with Cam Locks.
Attach unit from Step 4 to unit with
Cam Locks, Flat Washers, Spring Washers
and Head Cap Bolts, tightening bolts
only halfway.
Attach Rails (B) to unit with
Wood Screws.
C
Wood Screw
B
Flat Washer
Cam Lock
Head Cap Bolt
Spring Washer
I
H
B
CC
Cam Lock
I

Assembly Instructions 5/9
STEP 7
Attach Top (A) to unit with
Cam Locks, Flat Washers,
Spring Washers and
Head Cap Bolts, tightening
bolts only halfway.
STEP 6
Attach Rails (C) to unit with Cam Locks.
Attach Side Panel (G) to unit with Cam Locks
Flat Washers, Spring Washers, Head Cap Bolts
and Wood Screws, tightening bolts only halfway.
Turn unit to it’s upright position.
A
G
Flat Washer
Head Cap Bolt
Spring Washer
Cam Lock
Wood Screw
Flat Washer
Head Cap Bolt
Spring Washer
Cam Lock
C
CC