Home Styles 88 5002 642 User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
88 5002 642
Americana Dish Pantry
(Please refer to the last page of these
instructions for drawer assembly steps.)
Also need the following from carton 88 5002 641 :
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
D.
Side Panel
1 Pc.
E.
Side Panel
1 Pc.
M.
Drawer
4 Pcs.
N.
Base
1 Pc.
F.
Back Stretcher
2 Pcs.
G.
Back Upright
1 Pc.
H.
Back Panel
2 Pcs.

Assembly Instructions 3
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
*After assembly item must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Insert Cam Lock Screws into pre-drilled holes of Top (A), Side Panels (B), (C), (D), (E)
and Middle Panel (I).
(see Figure 1)
B
DC
E
A
I
Figure 1
Cam Lock Screw
2/5

Assembly Instructions 4
STEP 3
Attach Base (N) to the unit with Head Cap Bolts.
(see Figure 3)
STEP 4
Attach Back Stretcher (F) to Side Panel (C) with
Cam Lock.
Attach Back Upright (G) to Back Stretcher (F).
Slide Back Panels (H) into place.
Attach Back Stretcher (F) to unit with Cam Lock.
Attach Side Panel (B) to the unit with Cam Locks.
Head Cap Bolt
Figure 3
N
B
C
FF
H
H
G
D
FF
H
H
G
E
Figure 2
STEP 2
Attach Back Stretcher (F) to Side Panel (E) with
Cam Lock.
Attach Back Upright (G) to Back Stretcher (F).
Slide Back Panels (H) into place.
Attach Back Stretcher (F) to unit with Cam Lock.
Attach Side Panel (D) to the unit with Cam Locks.
(see Figure 2)
Cam Lock
Cam Lock
3/5

Assembly Instructions 5
M
M
M
M
L
L
A
I
J
J
K
K
Cam Lock
Wood Screw (short)
Adjustable Pin
Figure 7
Note : Please make sure unit
is level before tightening
these screws.
STEP 5
Turn the unit from Step 2 to its’ upright position.
Attach Middle Panel (I) to the unit from Step 2 with
Cam Locks.
Attach Knobs to Doors (J) and Doors (K) with
Machine Screws. (see Figure 4)
Attach Door (J) and Door (K) to the unit by sliding the
door lift hinges into the side panel lift hinges.
(see Figure 5)
Attach unit from Step 4 to Middle Panel (I) with
Cam Locks.
Place Top (A) onto unit and attach with Cam Locks.
Attach Door (J) and Door (K) to unit by sliding the door
lift hinges into the side panel lift hinges.
STEP 6
Insert Adjustable Pins into the
side panels at the desired level.
Place Shelves (L) into position.
Slide Drawers (M) into position.
Level the unit by adjusting the
adjustable levelers on the
bottom of unit. (see Figure 6)
Insert Wood Screws (short) into
the pre-drilled holes in the
back panel. (see Figure 7)
Figure 4 Figure 5 Figure 6
4/5

Assembly Instructions 6
Part List
Drawer M
M1.
Front Part
4 Pcs.
M2.
Back Part
4 Pcs.
M3.
Side Part
4 Pcs.
M4.
Side Part
4 Pcs.
M5.
Base Part
4 Pcs.
M6.
Support Drawer Part
4 Pcs.
M1
M1
M5
M5
M6
M2
M3
M3
M4
M4
STEP 1
Attach M1, M2 and M3 using a Phillips
screwdriver and long wood screws (4X),
tighten halfway.
Attach M1, M2 and M4 using long wood screws
(4X), tighten halfway. (see Figure 1)
STEP 2
Slide M5 into grooves in M3 and M4. Be sure
to push M5 all the way forward so it meet M1.
(see Figure 2)
STEP 3
Insert short wood screws (8X) into the
pre-drilled holes in M5, tighten screws.
Attach M6 to M5 with long wood screws (4X).
(see Figure 3)
Figure 1
Figure 2
Figure 3
MAKE SURE ROLLER
IS ON THE BACK
Tighten all screws used in drawer assembly.
5/5
Wood Screw (short) Wood Screw (long)